Preliminary ADM5120 support, marked as broken

SVN-Revision: 6614

32 files changed, 4946 insertions, 0 deletions

diff --git a/target/linux/adm5120-2.6/Makefile b/target/linux/adm5120-2.6/Makefile
new file mode 100644
index 0000000000..80b35e7efd
--- /dev/null
+++ b/target/linux/adm5120-2.6/Makefile
@@ -0,0 +1,22 @@
+# 
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+
+ARCH:=mipsel
+BOARD:=adm5120
+BOARDNAME:=ADMtek 5120
+FEATURES:=jffs2 broken
+
+define Target/Description
+	Build firmware images for ADMTek ADM5120 based boards
+	(e.g : RouterBoard RB112, Compex WP54G ...)
+endef
+
+include $(INCLUDE_DIR)/kernel-build.mk
+DEFAULT_PACKAGES += kmod-madwifi
+
+$(eval $(call BuildKernel))
diff --git a/target/linux/adm5120-2.6/config/default b/target/linux/adm5120-2.6/config/default
new file mode 100644
index 0000000000..e5894fc9cb
--- /dev/null
+++ b/target/linux/adm5120-2.6/config/default
@@ -0,0 +1,413 @@
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+# CONFIG_64BIT_PHYS_ADDR is not set
+CONFIG_ADM5120_GPIO=y
+CONFIG_ADM5120_NR_UARTS=2
+# CONFIG_ARPD is not set
+# CONFIG_ATM is not set
+CONFIG_AUDIT=y
+CONFIG_AUDIT_GENERIC=y
+CONFIG_BASE_SMALL=0
+CONFIG_BINFMT_MISC=m
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BONDING is not set
+CONFIG_BRIDGE_EBT_802_3=y
+CONFIG_BRIDGE_EBT_AMONG=y
+CONFIG_BRIDGE_EBT_ARP=y
+CONFIG_BRIDGE_EBT_ARPREPLY=y
+CONFIG_BRIDGE_EBT_BROUTE=y
+CONFIG_BRIDGE_EBT_DNAT=y
+CONFIG_BRIDGE_EBT_IP=y
+CONFIG_BRIDGE_EBT_LIMIT=y
+CONFIG_BRIDGE_EBT_LOG=y
+CONFIG_BRIDGE_EBT_MARK=y
+CONFIG_BRIDGE_EBT_MARK_T=y
+CONFIG_BRIDGE_EBT_PKTTYPE=y
+CONFIG_BRIDGE_EBT_REDIRECT=y
+CONFIG_BRIDGE_EBT_SNAT=y
+CONFIG_BRIDGE_EBT_STP=y
+CONFIG_BRIDGE_EBT_T_FILTER=y
+CONFIG_BRIDGE_EBT_T_NAT=y
+CONFIG_BRIDGE_EBT_ULOG=y
+CONFIG_BRIDGE_EBT_VLAN=y
+CONFIG_BRIDGE_NF_EBTABLES=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBFUSB is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIUSB is not set
+CONFIG_CIFS_DEBUG2=y
+CONFIG_CIFS_EXPERIMENTAL=y
+CONFIG_CIFS_STATS2=y
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CMDLINE="console=ttyS0,115200 rootfs=jffs2,squashfs init=/etc/preinit"
+# CONFIG_CPU_BIG_ENDIAN is not set
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+CONFIG_CPU_MIPSR1=y
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_VR41XX is not set
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_SHA1=y
+# CONFIG_DDB5477 is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_INFO is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_DEBUG_LOCKING_API_SELFTESTS=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_DEBUG_RWSEMS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_VM is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_DEFAULT_TCP_CONG="cubic"
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_DM9000 is not set
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_ELF_CORE=y
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FORCED_INLINING=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FW_LOADER=m
+CONFIG_GENERIC_ACL=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_GEN_RTC is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_HFS_FS is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_1024 is not set
+# CONFIG_HZ_128 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_256 is not set
+# CONFIG_HZ_48 is not set
+# CONFIG_I2C is not set
+# CONFIG_IDE is not set
+# CONFIG_IKCONFIG is not set
+# CONFIG_IMQ is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+CONFIG_INET_AH=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_ESP=y
+CONFIG_INET_IPCOMP=y
+CONFIG_INET_TCP_DIAG=y
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_XFRM_TUNNEL=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INPUT=y
+# CONFIG_INPUT_EVDEV is not set
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IPC_NS=y
+# CONFIG_IPSEC_NAT_TRAVERSAL is not set
+# CONFIG_IPV6 is not set
+# CONFIG_IP_DCCP is not set
+CONFIG_IP_NF_AMANDA=y
+# CONFIG_IP_NF_CT_PROTO_SCTP is not set
+CONFIG_IP_NF_FTP=y
+# CONFIG_IP_NF_H323 is not set
+CONFIG_IP_NF_IRC=y
+# CONFIG_IP_NF_PPTP is not set
+CONFIG_IP_NF_QUEUE=y
+# CONFIG_IP_NF_SET is not set
+# CONFIG_IP_NF_SIP is not set
+CONFIG_IP_NF_TFTP=y
+# CONFIG_IP_ROUTE_FWMARK is not set
+# CONFIG_IP_ROUTE_MULTIPATH is not set
+# CONFIG_IP_ROUTE_VERBOSE is not set
+# CONFIG_ISO9660_FS is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_POSIX_ACL=y
+CONFIG_JFFS2_FS_SECURITY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_SUMMARY=y
+# CONFIG_JFS_FS is not set
+# CONFIG_KGDB is not set
+CONFIG_LEDS_CLASS=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_LLC2 is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_VR41XX is not set
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_MII is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_MINI_FO is not set
+CONFIG_MIPS=y
+CONFIG_MIPS_ADM5120=y
+CONFIG_MIPS_ADM5120_ENET=y
+# CONFIG_MIPS_ATLAS is not set
+# CONFIG_MIPS_BOSPORUS is not set
+# CONFIG_MIPS_COBALT is not set
+# CONFIG_MIPS_DB1000 is not set
+# CONFIG_MIPS_DB1100 is not set
+# CONFIG_MIPS_DB1200 is not set
+# CONFIG_MIPS_DB1500 is not set
+# CONFIG_MIPS_DB1550 is not set
+# CONFIG_MIPS_EV64120 is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MALTA is not set
+# CONFIG_MIPS_MIRAGE is not set
+# CONFIG_MIPS_MTX1 is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+# CONFIG_MIPS_PB1000 is not set
+# CONFIG_MIPS_PB1100 is not set
+# CONFIG_MIPS_PB1200 is not set
+# CONFIG_MIPS_PB1500 is not set
+# CONFIG_MIPS_PB1550 is not set
+# CONFIG_MIPS_SEAD is not set
+# CONFIG_MIPS_SIM is not set
+# CONFIG_MIPS_UNCACHED is not set
+# CONFIG_MIPS_VPE_LOADER is not set
+# CONFIG_MIPS_XXS1500 is not set
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_MOMENCO_JAGUAR_ATX is not set
+# CONFIG_MOMENCO_OCELOT is not set
+# CONFIG_MOMENCO_OCELOT_3 is not set
+# CONFIG_MOMENCO_OCELOT_C is not set
+# CONFIG_MOMENCO_OCELOT_G is not set
+# CONFIG_MSDOS_FS is not set
+CONFIG_MTD=y
+# CONFIG_MTD_ABSENT is not set
+CONFIG_MTD_ADM5120=y
+# CONFIG_MTD_BLOCK is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+# CONFIG_MTD_BLOCK_RO is not set
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_CONCAT=m
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MTDRAM is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_OBSOLETE_CHIPS is not set
+# CONFIG_MTD_ONENAND is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PLATRAM is not set
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_RAM is not set
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
+CONFIG_MTD_REDBOOT_PARTS=m
+CONFIG_MTD_REDBOOT_PARTS_READONLY=y
+CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_NETFILTER_XTABLES is not set
+# CONFIG_NET_CLS_ACT is not set
+# CONFIG_NET_CLS_BASIC is not set
+# CONFIG_NET_CLS_FW is not set
+# CONFIG_NET_CLS_POLICE is not set
+# CONFIG_NET_CLS_ROUTE4 is not set
+# CONFIG_NET_CLS_RSVP is not set
+# CONFIG_NET_CLS_RSVP6 is not set
+# CONFIG_NET_CLS_TCINDEX is not set
+# CONFIG_NET_CLS_U32 is not set
+# CONFIG_NET_EMATCH is not set
+# CONFIG_NET_ESTIMATOR is not set
+# CONFIG_NET_IPGRE is not set
+CONFIG_NET_IPIP=y
+CONFIG_NET_KEY=y
+# CONFIG_NET_PCI is not set
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_RADIO is not set
+# CONFIG_NET_SCH_CBQ is not set
+# CONFIG_NET_SCH_DSMARK is not set
+# CONFIG_NET_SCH_ESFQ is not set
+# CONFIG_NET_SCH_GRED is not set
+# CONFIG_NET_SCH_HFSC is not set
+CONFIG_NET_SCH_HTB=y
+# CONFIG_NET_SCH_INGRESS is not set
+# CONFIG_NET_SCH_NETEM is not set
+# CONFIG_NET_SCH_PRIO is not set
+# CONFIG_NET_SCH_RED is not set
+# CONFIG_NET_SCH_SFQ is not set
+# CONFIG_NET_SCH_TBF is not set
+# CONFIG_NET_SCH_TEQL is not set
+# CONFIG_NET_VENDOR_3COM is not set
+CONFIG_NFSD_V2_ACL=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFS_ACL_SUPPORT=m
+CONFIG_NFS_DIRECTIO=y
+CONFIG_NFS_V3_ACL=y
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_NTFS_FS is not set
+# CONFIG_PAGE_SIZE_16KB is not set
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_64KB is not set
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PARTITION_ADVANCED is not set
+# CONFIG_PCCARD is not set
+CONFIG_PCI_ADM5120=y
+# CONFIG_PCI_DEBUG is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_V2PCI is not set
+CONFIG_POSIX_MQUEUE=y
+CONFIG_PPP=y
+CONFIG_PPPOE=y
+# CONFIG_PPP_ASYNC is not set
+# CONFIG_PPP_BSDCOMP is not set
+# CONFIG_PPP_DEFLATE is not set
+# CONFIG_PPP_MPPE is not set
+# CONFIG_PPP_MULTILINK is not set
+# CONFIG_PPP_SYNC_TTY is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_REISERFS_FS is not set
+CONFIG_RELAY=y
+# CONFIG_ROMFS_FS is not set
+# CONFIG_RTC is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_RUNTIME_DEBUG is not set
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_SCHEDSTATS is not set
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+# CONFIG_SCSI is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SERIAL_8250_EXTENDED is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_ADM5120=y
+CONFIG_SERIO=y
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP32 is not set
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_PTSWARM is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_SWARM is not set
+CONFIG_SLHC=y
+# CONFIG_SOUND is not set
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SYN_COOKIES=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_TEXTSEARCH_KMP=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_TOSHIBA_JMR3927 is not set
+# CONFIG_TOSHIBA_RBTX4927 is not set
+# CONFIG_TOSHIBA_RBTX4938 is not set
+CONFIG_TRAD_SIGNALS=y
+# CONFIG_TUN is not set
+# CONFIG_UDF_FS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_USB=y
+# CONFIG_USB_ACM is not set
+CONFIG_USB_ADM5120_HCD=y
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_DEVICEFS is not set
+# CONFIG_USB_EHCI_HCD is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_SERIAL is not set
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_USB_USBNET_MII is not set
+CONFIG_UTS_NS=y
+# CONFIG_VFAT_FS is not set
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_WATCHDOG is not set
+CONFIG_XFRM_SUB_POLICY=y
+CONFIG_XFRM_USER=y
+# CONFIG_XFS_FS is not set
diff --git a/target/linux/adm5120-2.6/files/arch/mips/adm5120/Makefile b/target/linux/adm5120-2.6/files/arch/mips/adm5120/Makefile
new file mode 100644
index 0000000000..63024e36da
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/adm5120/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the ADMtek ADM5120 SoC specific parts of the kernel
+#
+
+obj-y  := setup.o prom.o irq.o memory.o mipsIRQ.o
+
+EXTRA_AFLAGS := $(CFLAGS)
diff --git a/target/linux/adm5120-2.6/files/arch/mips/adm5120/irq.c b/target/linux/adm5120-2.6/files/arch/mips/adm5120/irq.c
new file mode 100644
index 0000000000..46f3bb05ee
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/adm5120/irq.c
@@ -0,0 +1,156 @@
+/*
+ *	Copyright (C) ADMtek Incorporated.
+ *		Creator : daniell@admtek.com.tw
+ *	Carsten Langgaard, carstenl@mips.com
+ *	Copyright (C) 2000, 2001 MIPS Technologies, Inc.
+ *	Copyright (C) 2001 Ralf Baechle
+ *	Copyright (C) 2005 Jeroen Vreeken (pe1rxq@amsat.org)
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/random.h>
+#include <linux/pm.h>
+
+#include <asm/irq.h>
+#include <asm/time.h>
+#include <asm/mipsregs.h>
+#include <asm/gdb-stub.h>
+#include <asm/irq_cpu.h>
+
+#define MIPS_CPU_TIMER_IRQ 7
+
+extern int setup_irq(unsigned int irq, struct irqaction *irqaction);
+extern irq_desc_t irq_desc[];
+extern asmlinkage void mipsIRQ(void);
+
+int mips_int_lock(void);
+void mips_int_unlock(int);
+
+unsigned int mips_counter_frequency;
+
+#define ADM5120_INTC_REG(reg)	(*(volatile u32 *)(KSEG1ADDR(0x12200000+(reg))))
+#define ADM5120_INTC_STATUS	ADM5120_INTC_REG(0x00)
+#define ADM5120_INTC_ENABLE	ADM5120_INTC_REG(0x08)
+#define ADM5120_INTC_DISABLE	ADM5120_INTC_REG(0x0c)
+#define ADM5120_IRQ_MAX		9
+#define ADM5120_IRQ_MASK	0x3ff
+
+void adm5120_hw0_irqdispatch(struct pt_regs *regs)
+{
+	unsigned long intsrc;
+	int i;
+
+	intsrc = ADM5120_INTC_STATUS & ADM5120_IRQ_MASK;
+
+	for (i = 0; intsrc; intsrc >>= 1, i++)
+		if (intsrc & 0x1)
+			do_IRQ(i);
+		else
+			spurious_interrupt();
+}
+
+void mips_timer_interrupt(struct pt_regs *regs)
+{
+        write_c0_compare(read_c0_count()+ mips_counter_frequency/HZ);
+        ll_timer_interrupt(MIPS_CPU_TIMER_IRQ);
+}
+
+/* Main interrupt dispatcher */
+asmlinkage void plat_irq_dispatch(struct pt_regs *regs)
+{
+        unsigned int cp0_cause = read_c0_cause() & read_c0_status();
+
+        if (cp0_cause & CAUSEF_IP7) {
+                mips_timer_interrupt( regs);
+        } else if (cp0_cause & CAUSEF_IP2) {
+                adm5120_hw0_irqdispatch( regs);
+        }
+}
+
+void enable_adm5120_irq(unsigned int irq)
+{
+	int s;
+
+	/* Disable all interrupts (FIQ/IRQ) */
+	s = mips_int_lock();
+
+	if ((irq < 0) || (irq > ADM5120_IRQ_MAX)) 
+		goto err_exit;
+
+	ADM5120_INTC_ENABLE = (1<<irq);
+
+err_exit:
+
+	/* Restore the interrupts states */
+	mips_int_unlock(s);
+}
+
+
+void disable_adm5120_irq(unsigned int irq)
+{
+	int s;
+
+	/* Disable all interrupts (FIQ/IRQ) */
+	s = mips_int_lock();
+
+	if ((irq < 0) || (irq > ADM5120_IRQ_MAX)) 
+		goto err_exit;
+
+	ADM5120_INTC_DISABLE = (1<<irq);
+
+err_exit:
+	/* Restore the interrupts states */
+	mips_int_unlock(s);
+}
+
+unsigned int startup_adm5120_irq(unsigned int irq)
+{
+	enable_adm5120_irq(irq);
+	return 0;
+}
+
+void shutdown_adm5120_irq(unsigned int irq)
+{
+	disable_adm5120_irq(irq);
+}
+
+static inline void ack_adm5120_irq(unsigned int irq_nr)
+{
+	ADM5120_INTC_DISABLE = (1 << irq_nr);
+}
+
+
+static void end_adm5120_irq(unsigned int irq_nr)
+{
+	ADM5120_INTC_ENABLE = (1 << irq_nr);
+}
+
+static hw_irq_controller adm5120_irq_type = {
+	.typename 	= "MIPS",
+	.startup	= startup_adm5120_irq,
+	.shutdown	= shutdown_adm5120_irq,
+	.enable		= enable_adm5120_irq,
+	.disable	= disable_adm5120_irq,
+	.ack 		= ack_adm5120_irq,
+	.end		= end_adm5120_irq,
+	.set_affinity	= NULL,
+};
+
+
+void __init arch_init_irq(void)
+{
+	int i;
+	
+	for (i = 0; i <= ADM5120_IRQ_MAX; i++) {
+		irq_desc[i].status = IRQ_DISABLED;
+		irq_desc[i].action = 0;
+		irq_desc[i].depth = 1;
+		irq_desc[i].chip = &adm5120_irq_type;
+	}
+}
diff --git a/target/linux/adm5120-2.6/files/arch/mips/adm5120/memory.c b/target/linux/adm5120-2.6/files/arch/mips/adm5120/memory.c
new file mode 100644
index 0000000000..a8ffb0c8f3
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/adm5120/memory.c
@@ -0,0 +1,154 @@
+/*****************************************************************************
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2003 ADMtek Incorporated.
+ *	daniell@admtek.com.tw
+ * Copyright (C) 2005 Jeroen Vreeken (pe1rxq@amsat.org)
+ *
+ * ########################################################################
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ *****************************************************************************/
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/bootmem.h>
+#include <linux/pfn.h>
+#include <linux/string.h>
+
+#include <asm/bootinfo.h>
+#include <asm/page.h>
+#include <asm/sections.h>
+
+#include <asm-mips/mips-boards/prom.h>
+
+extern char *prom_getenv(char *envname);
+
+#define PFN_ALIGN(x)    (((unsigned long)(x) + (PAGE_SIZE - 1)) & PAGE_MASK)
+
+#define ADM5120_MEMCTRL			0x1200001c
+#define ADM5120_MEMCTRL_SDRAM_MASK	0x7
+
+static const unsigned long adm_sdramsize[] __initdata = {
+	0x0,		/* Reserved */
+	0x0400000,	/* 4Mb */
+	0x0800000,	/* 8Mb */
+	0x1000000,	/* 16Mb */
+	0x4000000,	/* 64Mb */
+	0x8000000,	/* 128Mb */
+};
+
+/* determined physical memory size, not overridden by command line args  */
+unsigned long physical_memsize = 0L;
+
+struct prom_pmemblock mdesc[PROM_MAX_PMEMBLOCKS];
+
+struct prom_pmemblock * __init prom_getmdesc(void)
+{
+	char *memsize_str;
+	unsigned int memsize;
+	char cmdline[CL_SIZE], *ptr;
+
+	memsize_str = prom_getenv("memsize");
+
+	if (!memsize_str)
+	{
+		prom_printf("memsize not set in boot prom, set to default (8Mb)\n");
+		physical_memsize = 0x00800000;
+	}
+	else
+#ifdef DEBUG
+		prom_printf("prom_memsize = %s\n", memsize_str);
+#endif
+		physical_memsize = simple_strtol(memsize_str, NULL, 0);
+
+	/* Check the command line for a memsize directive that overrides
+	 * the physical/default amount */
+	strcpy(cmdline, arcs_cmdline);
+	ptr = strstr(cmdline, "memsize=");
+	if (ptr && (ptr != cmdline) && (*(ptr - 1) != ' '))
+	ptr = strstr(ptr, " memsize=");
+	
+	if (ptr)
+		memsize = memparse(ptr + 8, &ptr);
+	else
+		memsize = physical_memsize;
+
+       memset(mdesc, 0, sizeof(mdesc));
+
+       mdesc[0].type = BOOT_MEM_RAM;
+       mdesc[0].base = CPHYSADDR(PFN_ALIGN(&_end));
+       mdesc[0].size = memsize - mdesc[0].base;
+
+       return &mdesc[0];
+}
+
+void __init prom_meminit(void)
+{
+	struct prom_pmemblock *p;
+
+	p = prom_getmdesc();
+
+	while (p->size)
+	{
+		long type;
+		unsigned long base, size;
+		base = p->base;
+		type = p->type,
+		size = p->size;
+		add_memory_region(base, size, type);
+		p++;
+	}
+}
+
+#if 0
+void __init prom_meminit(void)
+{
+	unsigned long base = CPHYSADDR(PFN_ALIGN(&_end));
+	unsigned long size;
+
+	u32 memctrl = *(u32*)KSEG1ADDR(ADM5120_MEMCTRL);
+	size = adm_sdramsize[memctrl & ADM5120_MEMCTRL_SDRAM_MASK];
+	add_memory_region(base, size-base, BOOT_MEM_RAM);
+}
+#endif
+
+unsigned long __init prom_free_prom_memory(void)
+{
+        unsigned long freed = 0;
+        unsigned long addr;
+        int i;
+
+        for (i = 0; i < boot_mem_map.nr_map; i++) {
+                if (boot_mem_map.map[i].type != BOOT_MEM_ROM_DATA)
+                        continue;
+
+                addr = PAGE_ALIGN(boot_mem_map.map[i].addr);
+                while (addr < boot_mem_map.map[i].addr
+                              + boot_mem_map.map[i].size) {
+                        ClearPageReserved(virt_to_page(__va(addr)));
+                        init_page_count(virt_to_page(__va(addr)));
+                        free_page((unsigned long)__va(addr));
+                        addr += PAGE_SIZE;
+                        freed += PAGE_SIZE;
+                }
+        }
+        printk("Freeing prom memory: %ldkb freed\n", freed >> 10);
+
+        return freed;
+}
diff --git a/target/linux/adm5120-2.6/files/arch/mips/adm5120/mipsIRQ.S b/target/linux/adm5120-2.6/files/arch/mips/adm5120/mipsIRQ.S
new file mode 100644
index 0000000000..f118fb402b
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/adm5120/mipsIRQ.S
@@ -0,0 +1,135 @@
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999, 2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * ########################################################################
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ * Interrupt exception dispatch code.
+ *
+ */
+#include <linux/autoconf.h>
+
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+
+#define STATUS_IE	0x00000001
+
+/* A lot of complication here is taken away because:
+ *
+ * 1) We handle one interrupt and return, sitting in a loop and moving across
+ *    all the pending IRQ bits in the cause register is _NOT_ the answer, the
+ *    common case is one pending IRQ so optimize in that direction.
+ *
+ * 2) We need not check against bits in the status register IRQ mask, that
+ *    would make this routine slow as hell.
+ *
+ * 3) Linux only thinks in terms of all IRQs on or all IRQs off, nothing in
+ *    between like BSD spl() brain-damage.
+ *
+ * Furthermore, the IRQs on the MIPS board look basically (barring software
+ * IRQs which we don't use at all and all external interrupt sources are
+ * combined together on hardware interrupt 0 (MIPS IRQ 2)) like:
+ *
+ *	MIPS IRQ	Source
+ *      --------        ------
+ *             0	Software (ignored)
+ *             1        Software (ignored)
+ *             2        Combined hardware interrupt (hw0)
+ *             3        Hardware (ignored)
+ *             4        Hardware (ignored)
+ *             5        Hardware (ignored)
+ *             6        Hardware (ignored)
+ *             7        R4k timer (what we use)
+ *
+ * Note: On the SEAD board thing are a little bit different.
+ *       Here IRQ 2 (hw0) is wired to the UART0 and IRQ 3 (hw1) is wired
+ *       wired to UART1.
+ *	
+ * We handle the IRQ according to _our_ priority which is:
+ *
+ * Highest ----     R4k Timer
+ * Lowest  ----     Combined hardware interrupt
+ *
+ * then we just return, if multiple IRQs are pending then we will just take
+ * another exception, big deal.
+ */
+
+	.text
+	.set	noreorder
+	.set	noat
+	.align	5
+
+NESTED(mipsIRQ, PT_SIZE, sp)
+	SAVE_ALL
+	CLI
+	.set	at
+
+	mfc0	s0, CP0_CAUSE		
+	mfc0	s1, CP0_STATUS
+	and     s0, s0, s1
+	
+	/* First we check for r4k counter/timer IRQ. */
+	andi	a0, s0, CAUSEF_IP7
+	beq		a0, zero, 1f
+	nop
+
+	move	a0, sp
+	jal		mips_timer_interrupt
+	nop
+
+	j		ret_from_irq
+	nop				
+
+1:
+	andi	a0, s0, CAUSEF_IP2
+	beq		a0, zero, 1f	
+	nop
+	
+	move	a0, sp			
+	jal		adm5120_hw0_irqdispatch	 
+	nop
+1:
+	j		ret_from_irq
+	nop							
+
+END(mipsIRQ)
+
+
+LEAF(mips_int_lock)
+	.set noreorder
+	mfc0	v0, CP0_STATUS
+	li		v1, ~STATUS_IE
+	and		v1, v1, v0
+	mtc0	v1, CP0_STATUS
+	j		ra
+	and		v0, v0, STATUS_IE
+	.set reorder
+END(mips_int_lock)
+
+
+LEAF(mips_int_unlock)
+	mfc0	v0, CP0_STATUS
+	and		a0, a0, STATUS_IE
+	or		v0, v0, a0
+	mtc0	v0, CP0_STATUS
+	j		ra
+	nop
+END(mips_int_unlock)
+
diff --git a/target/linux/adm5120-2.6/files/arch/mips/adm5120/prom.c b/target/linux/adm5120-2.6/files/arch/mips/adm5120/prom.c
new file mode 100644
index 0000000000..ba8051ea8c
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/adm5120/prom.c
@@ -0,0 +1,113 @@
+/*****************************************************************************
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2003 ADMtek Incorporated.
+ *	daniell@admtek.com.tw
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ *****************************************************************************/
+
+#include <linux/init.h>
+#include <linux/autoconf.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/bootmem.h>
+
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+
+void setup_prom_printf(int);
+void prom_printf(char *, ...);
+void prom_meminit(void);
+
+#define ADM5120_ENVC           1
+
+char *adm5120_envp[2*ADM5120_ENVC] = {"memsize","0x001000000"};
+
+#define READCSR(r)      *(volatile unsigned long *)(0xB2600000+(r))
+#define WRITECSR(r,v)   *(volatile unsigned long *)(0xB2600000+(r)) = v
+
+#define UART_DR_REG         0x00
+#define UART_FR_REG         0x18
+#define UART_TX_FIFO_FULL   0x20
+
+int putPromChar(char c)
+{
+	WRITECSR(UART_DR_REG, c);
+        while ( (READCSR(UART_FR_REG) & UART_TX_FIFO_FULL) );
+        return 0;
+}
+
+/*
+ * Ugly prom_printf used for debugging
+ */
+
+void prom_printf(char *fmt, ...)
+{
+        va_list args;
+        int l;
+        char *p, *buf_end;
+        char buf[1024];
+
+        va_start(args, fmt);
+        l = vsprintf(buf, fmt, args); /* hopefully i < sizeof(buf) */
+        va_end(args);
+
+        buf_end = buf + l;
+
+        for (p = buf; p < buf_end; p++) {
+                /* Crude cr/nl handling is better than none */
+                if (*p == '\n')
+                        putPromChar('\r');
+                putPromChar(*p);
+        }
+}
+
+char *prom_getenv(char *envname)
+{
+	int i, index=0;
+
+	i = strlen(envname);
+
+	printk(KERN_INFO "GETENV: envname is %s\n", envname);
+
+	while(index < (2*ADM5120_ENVC)) {
+		if(strncmp(envname, adm5120_envp[index], i) == 0) {
+			printk(KERN_INFO "GETENV: returning %s\n", adm5120_envp[index+1]);
+			return(adm5120_envp[index+1]);
+		}
+		index += 2;
+	}
+
+	printk(KERN_INFO "GETENV: not found.\n");
+	return(NULL);
+}
+	
+/*
+ * initialize the prom module.
+ */
+void __init prom_init(void)
+{
+	/* you should these macros defined in include/asm/bootinfo.h */
+	mips_machgroup = MACH_GROUP_ADM_GW;
+	mips_machtype = MACH_ADM_GW_5120;
+
+	/* init command line, register a default kernel command line */
+	strcpy(&(arcs_cmdline[0]), "console=ttyS0,115200 rootfstype=jffs2 init=/etc/preinit");
+
+	/* init memory map */
+	prom_meminit();
+}
diff --git a/target/linux/adm5120-2.6/files/arch/mips/adm5120/setup.c b/target/linux/adm5120-2.6/files/arch/mips/adm5120/setup.c
new file mode 100644
index 0000000000..23e668411c
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/adm5120/setup.c
@@ -0,0 +1,132 @@
+/*
+ *	Copyright (C) ADMtek Incorporated.
+ *		Creator : daniell@admtek.com.tw
+ *	Copyright 1999, 2000 MIPS Technologies, Inc.
+ *	Copyright Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+
+#include <asm/reboot.h>
+#include <asm/io.h>
+#include <asm/time.h>
+
+#define ADM5120_SOFTRESET	0x12000004
+#define STATUS_IE		0x00000001
+#define ALLINTS (IE_IRQ0 | IE_IRQ5 | STATUS_IE)
+
+#define ADM5120_CODEREG		0x12000000
+#define ADM5120_CPU_CLK_MASK	0x00300000
+#define ADM5120_CPU_CLK_175	0x00000000
+#define ADM5120_CPU_CLK_200	0x00100000
+#define ADM5120_CPU_CLK_225	0x00200000
+#define ADM5120_CPU_CLK_250	0x00300000
+
+void  mips_time_init(void);
+
+extern unsigned int mips_counter_frequency;
+
+void adm5120_restart(char *command)
+{
+	*(u32*)KSEG1ADDR(ADM5120_SOFTRESET)=1;
+}
+
+
+void adm5120_halt(void)
+{
+        printk(KERN_NOTICE "\n** You can safely turn off the power\n");
+        while (1);
+}
+
+
+void adm5120_power_off(void)
+{
+        adm5120_halt();
+}
+
+void __init mips_time_init(void)
+{
+	u32 clock;
+
+	clock = *(u32*)KSEG1ADDR(ADM5120_CODEREG);
+
+	switch (clock & ADM5120_CPU_CLK_MASK) {
+		case ADM5120_CPU_CLK_175:
+			mips_counter_frequency = 87500000;
+			printk("CPU clock: 175MHz\n");
+			break;
+		case ADM5120_CPU_CLK_200:
+			mips_counter_frequency = 100000000;
+			printk("CPU clock: 200MHz\n");
+			break;
+		case ADM5120_CPU_CLK_225:
+			mips_counter_frequency = 112500000;
+			printk("CPU clock: 225MHz\n");
+			break;
+		case ADM5120_CPU_CLK_250:
+			mips_counter_frequency = 125000000;
+			printk("CPU clock: 250MHz\n");
+			break;
+	}
+}
+
+void __init plat_timer_setup(struct irqaction *irq)
+{
+	/* to generate the first timer interrupt */
+	write_c0_compare(read_c0_count()+ mips_counter_frequency/HZ);
+	clear_c0_status(ST0_BEV);
+	set_c0_status(ALLINTS);
+}
+
+void __init plat_mem_setup(void)
+{
+	printk(KERN_INFO "ADM5120 board setup\n");
+
+	board_time_init = mips_time_init;
+	//board_timer_setup = mips_timer_setup;
+
+	_machine_restart = adm5120_restart;
+	_machine_halt = adm5120_halt;
+	pm_power_off = adm5120_power_off;
+
+	set_io_port_base(KSEG1);
+}
+
+const char *get_system_type(void)
+{
+	return "ADM5120 Board";
+}
+
+static struct resource adm5120_hcd_resources[] = {
+	[0] = {
+		.start	= 0x11200000,
+		.end	= 0x11200084,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= 0x3,
+		.end	= 0x3,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device adm5120hcd_device = {
+	.name		= "adm5120-hcd",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(adm5120_hcd_resources),
+	.resource	= adm5120_hcd_resources,
+};
+
+static struct platform_device *devices[] __initdata = {
+	&adm5120hcd_device,
+};
+
+static int __init adm5120_init(void)
+{
+	return platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
+subsys_initcall(adm5120_init);
diff --git a/target/linux/adm5120-2.6/files/arch/mips/pci/ops-adm5120.c b/target/linux/adm5120-2.6/files/arch/mips/pci/ops-adm5120.c
new file mode 100644
index 0000000000..80b8531eab
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/pci/ops-adm5120.c
@@ -0,0 +1,59 @@
+/*
+ *	Copyright (C) ADMtek Incorporated.
+ *	Copyright (C) 2005 Jeroen Vreeken (pe1rxq@amsat.org)
+ */
+
+#include <linux/autoconf.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+volatile u32* pci_config_address_reg = (volatile u32*)KSEG1ADDR(0x115ffff0);
+volatile u32* pci_config_data_reg = (volatile u32*)KSEG1ADDR(0x115ffff8);
+
+#define PCI_ENABLE 0x80000000
+                          
+static int pci_config_read(struct pci_bus *bus, unsigned int devfn, int where,
+                           int size, uint32_t *val)
+{
+	*pci_config_address_reg = ((bus->number & 0xff) << 0x10) |
+	    ((devfn & 0xff) << 0x08) | (where & 0xfc) | PCI_ENABLE;
+	switch (size) {
+		case 1:
+			*val = ((*pci_config_data_reg)>>((where&3)<<3))&0xff;
+			break;
+		case 2:
+			*val = ((*pci_config_data_reg)>>((where&3)<<3))&0xffff;
+			break;
+		default:
+			*val = (*pci_config_data_reg);
+	}
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_config_write(struct pci_bus *bus, unsigned int devfn, int where,
+                            int size, uint32_t val)
+{
+	*pci_config_address_reg = ((bus->number & 0xff) << 0x10) |
+	    ((devfn & 0xff) << 0x08) | (where & 0xfc) | PCI_ENABLE;
+	switch (size) {
+		case 1:
+			*(volatile u8 *)(((int)pci_config_data_reg) +
+			    (where & 3)) = val;
+			break;
+		case 2:
+			*(volatile u16 *)(((int)pci_config_data_reg) +
+			    (where & 2)) = (val);
+			break;
+		default:
+			*pci_config_data_reg = (val);
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops adm5120_pci_ops = {
+	.read	= pci_config_read,
+	.write	= pci_config_write,
+};
diff --git a/target/linux/adm5120-2.6/files/arch/mips/pci/pci-adm5120.c b/target/linux/adm5120-2.6/files/arch/mips/pci/pci-adm5120.c
new file mode 100644
index 0000000000..a8585747ee
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/arch/mips/pci/pci-adm5120.c
@@ -0,0 +1,93 @@
+/*
+ *	Copyright (C) ADMtek Incorporated.
+ *	Copyright (C) 2005 Jeroen Vreeken (pe1rxq@amsat.org)
+ */
+
+#include <linux/autoconf.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+extern struct pci_ops adm5120_pci_ops;
+
+#define ADM5120_CODE		0x12000000
+#define ADM5120_CODE_PQFP	0x20000000
+
+#define PCI_CMM_IOACC_EN	0x1
+#define PCI_CMM_MEMACC_EN	0x2
+#define PCI_CMM_MASTER_EN	0x4
+#define PCI_CMM_DEF \
+		(PCI_CMM_IOACC_EN | PCI_CMM_MEMACC_EN | PCI_CMM_MASTER_EN)
+
+#define PCI_DEF_CACHE_LINE_SZ	4
+
+
+struct resource pci_io_resource = {
+	"PCI IO space", 
+	0x11500000,  
+	0x115ffff0-1,
+	IORESOURCE_IO
+};
+
+struct resource pci_mem_resource = {
+	"PCI memory space", 
+	0x11400000,
+	0x11500000,
+	IORESOURCE_MEM
+};
+
+static struct pci_controller adm5120_controller = {
+	.pci_ops	= &adm5120_pci_ops,
+	.io_resource	= &pci_io_resource,
+	.mem_resource	= &pci_mem_resource,
+};
+
+int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (slot < 2 || slot > 4)
+		return -1;
+	return slot + 4;
+}
+
+static void adm5120_pci_fixup(struct pci_dev *dev)
+{
+	if (dev->devfn == 0) {
+		pci_write_config_word(dev, PCI_COMMAND, PCI_CMM_DEF);
+		pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE,
+		    PCI_DEF_CACHE_LINE_SZ);
+		pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, 0);
+		pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, 0);
+	}
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, adm5120_pci_fixup);
+
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+static int __init adm5120_pci_setup(void)
+{
+
+	if ((*(volatile u32 *)(KSEG1ADDR(ADM5120_CODE))) & ADM5120_CODE_PQFP) {
+		printk("System has no PCI BIOS\n");
+		return 1;
+	}
+	printk("System has PCI BIOS\n");
+
+	/* Avoid ISA compat ranges.  */
+	PCIBIOS_MIN_IO = 0x00000000;
+	PCIBIOS_MIN_MEM = 0x00000000;
+
+	/* Set I/O resource limits.  */
+	ioport_resource.end = 0x1fffffff;
+	iomem_resource.end = 0xffffffff;	
+
+	register_pci_controller(&adm5120_controller);
+	return 0;
+}
+
+subsys_initcall(adm5120_pci_setup);
diff --git a/target/linux/adm5120-2.6/files/drivers/char/adm5120_gpio.c b/target/linux/adm5120-2.6/files/drivers/char/adm5120_gpio.c
new file mode 100644
index 0000000000..6fccfb029e
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/drivers/char/adm5120_gpio.c
@@ -0,0 +1,58 @@
+/*
+ *	ADM5120 LED (GPIO) driver
+ *
+ *	Copyright (C) Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ */
+
+#include <linux/autoconf.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/miscdevice.h>
+#include <linux/fs.h>
+
+#define LED_MINOR 151
+#define GPIO_IO        ((unsigned long *)0xb20000b8)
+
+static ssize_t adm5120_led_write(struct file *file, const char __user *data,
+	size_t len, loff_t *ppos)
+{
+	unsigned char val;
+
+	if (!len || get_user(val, data))
+		return -EFAULT;
+	*GPIO_IO=(*GPIO_IO & 0x00ffffff) | (val<<24);
+	return 1;
+}
+
+static struct file_operations adm5120_led_fops = {
+	.owner	= THIS_MODULE,
+	.write	= adm5120_led_write,
+};
+
+static struct miscdevice adm5120_led_device = {
+	LED_MINOR,
+	"led",
+	&adm5120_led_fops,
+};
+
+static int __init adm5120_led_init(void)
+{
+	printk(KERN_INFO "ADM5120 LED & GPIO driver\n");
+	if (misc_register(&adm5120_led_device)) {
+		printk(KERN_WARNING "Couldn't register device %d\n", LED_MINOR);
+		return -EBUSY;
+	}
+	return 0;
+}
+
+static void __exit adm5120_led_exit(void)
+{
+	misc_deregister(&adm5120_led_device);
+}
+
+module_init(adm5120_led_init);
+module_exit(adm5120_led_exit);
+
+MODULE_DESCRIPTION("ADM5120 LED and GPIO driver");
+MODULE_AUTHOR("Jeroen Vreeken");
+MODULE_LICENSE("GPL");
diff --git a/target/linux/adm5120-2.6/files/drivers/mtd/maps/adm5120_mtd.c b/target/linux/adm5120-2.6/files/drivers/mtd/maps/adm5120_mtd.c
new file mode 100644
index 0000000000..a9e97cb318
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/drivers/mtd/maps/adm5120_mtd.c
@@ -0,0 +1,55 @@
+/*
+ *	Flash device on the ADM5120 board
+ *
+ *	Copyright Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ *
+ *	This program is free software; you can redistribute it and/or
+ *	modify it under the terms of the GNU General Public License version
+ *	2 as published by the Free Software Foundation.
+ */
+
+#include <linux/autoconf.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+
+#define FLASH_PHYS_ADDR		0x1FC00000
+#define FLASH_SIZE 		0x200000  
+
+static struct mtd_info *adm5120_mtd;
+
+static struct map_info adm5120_mtd_map = {
+	.name = "ADM5120",
+	.size = FLASH_SIZE,
+	.bankwidth = 2,
+	.phys = FLASH_PHYS_ADDR,
+};
+
+static int __init adm5120_mtd_init(void)
+{
+	printk(KERN_INFO "ADM5120 board flash (0x%x at 0x%x)\n", FLASH_SIZE,
+	    FLASH_PHYS_ADDR);
+	adm5120_mtd_map.virt = ioremap_nocache(FLASH_PHYS_ADDR, FLASH_SIZE);
+	simple_map_init(&adm5120_mtd_map);
+	adm5120_mtd = do_map_probe("cfi_probe", &adm5120_mtd_map);
+	if (adm5120_mtd) {
+		adm5120_mtd->owner = THIS_MODULE;
+		add_mtd_device(adm5120_mtd);
+		return 0;
+	}
+	return -ENXIO;
+}
+
+static void __exit adm5120_mtd_exit(void)
+{
+	del_mtd_device(adm5120_mtd);
+	map_destroy(adm5120_mtd);
+}
+
+module_init(adm5120_mtd_init);
+module_exit(adm5120_mtd_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Jeroen Vreeken (pe1rxq@amsat.org)");
+MODULE_DESCRIPTION("MTD map driver for ADM5120 boards");
diff --git a/target/linux/adm5120-2.6/files/drivers/net/adm5120sw.c b/target/linux/adm5120-2.6/files/drivers/net/adm5120sw.c
new file mode 100644
index 0000000000..935016c3a1
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/drivers/net/adm5120sw.c
@@ -0,0 +1,502 @@
+/*
+ *	ADM5120 built in ethernet switch driver
+ *
+ *	Copyright Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ *
+ *	Inspiration for this driver came from the original ADMtek 2.4 
+ *	driver, Copyright ADMtek Inc.
+ */
+#include <linux/autoconf.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <asm/mipsregs.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+#include "adm5120sw.h"
+
+MODULE_AUTHOR("Jeroen Vreeken (pe1rxq@amsat.org)");
+MODULE_DESCRIPTION("ADM5120 ethernet switch driver");
+MODULE_LICENSE("GPL");
+
+/*
+ *	The ADM5120 uses an internal matrix to determine which ports
+ *	belong to which VLAN.
+ *	The default generates a VLAN (and device) for each port 
+ *	(including MII port) and the CPU port is part of all of them.
+ *
+ *	Another example, one big switch and everything mapped to eth0:
+ *	0x7f, 0x00, 0x00, 0x00, 0x00, 0x00
+ */
+static unsigned char vlan_matrix[SW_DEVS] = {
+	0x41, 0x42, 0x44, 0x48, 0x50, 0x60
+};
+
+static int adm5120_nrdevs;
+
+static struct net_device *adm5120_devs[SW_DEVS];
+static struct adm5120_dma 
+    adm5120_dma_txh_v[ADM5120_DMA_TXH] __attribute__((aligned(16))),
+    adm5120_dma_txl_v[ADM5120_DMA_TXL] __attribute__((aligned(16))),
+    adm5120_dma_rxh_v[ADM5120_DMA_RXH] __attribute__((aligned(16))),
+    adm5120_dma_rxl_v[ADM5120_DMA_RXL] __attribute__((aligned(16))),
+    *adm5120_dma_txh,
+    *adm5120_dma_txl,
+    *adm5120_dma_rxh,
+    *adm5120_dma_rxl;
+static struct sk_buff
+    *adm5120_skb_rxh[ADM5120_DMA_RXH],
+    *adm5120_skb_rxl[ADM5120_DMA_RXL],
+    *adm5120_skb_txh[ADM5120_DMA_TXH],
+    *adm5120_skb_txl[ADM5120_DMA_TXL];
+static int adm5120_rxhi = 0;
+static int adm5120_rxli = 0;
+/* We don't use high priority tx for now */
+/*static int adm5120_txhi = 0;*/
+static int adm5120_txli = 0;
+static int adm5120_txhit = 0;
+static int adm5120_txlit = 0;
+static int adm5120_if_open = 0;
+
+static inline void adm5120_set_reg(unsigned int reg, unsigned long val)
+{
+	*(volatile unsigned long*)(SW_BASE+reg) = val;
+}
+
+static inline unsigned long adm5120_get_reg(unsigned int reg)
+{
+	return *(volatile unsigned long*)(SW_BASE+reg);
+}
+
+static inline void adm5120_rxfixup(struct adm5120_dma *dma,
+    struct sk_buff **skbl, int num)
+{
+	int i;
+
+	/* Resubmit the entire ring */
+	for (i=0; i<num; i++) {
+		dma[i].status = 0;
+		dma[i].cntl = 0;
+		dma[i].len = ADM5120_DMA_RXSIZE;
+		dma[i].data = ADM5120_DMA_ADDR(skbl[i]->data) |
+		     ADM5120_DMA_OWN | (i==num-1 ? ADM5120_DMA_RINGEND : 0);
+	}
+}
+
+static inline void adm5120_rx(struct adm5120_dma *dma, struct sk_buff **skbl,
+    int *index, int num)
+{
+	struct sk_buff *skb, *skbn;
+	struct adm5120_sw *priv;
+	struct net_device *dev;
+	int port, vlan, len;
+
+	while (!(dma[*index].data & ADM5120_DMA_OWN)) {
+		port = (dma[*index].status & ADM5120_DMA_PORTID);
+		port >>= ADM5120_DMA_PORTSHIFT;
+		for (vlan = 0; vlan < adm5120_nrdevs; vlan++) {
+			if ((1<<port) & vlan_matrix[vlan])
+				break;
+		}
+		if (vlan == adm5120_nrdevs)
+			vlan = 0;
+		dev = adm5120_devs[vlan];
+		skb = skbl[*index];
+		len = (dma[*index].status & ADM5120_DMA_LEN);
+		len >>= ADM5120_DMA_LENSHIFT;
+		len -= ETH_FCS;
+
+		priv = netdev_priv(dev);
+		if (len <= 0 || len > ADM5120_DMA_RXSIZE ||
+		    dma[*index].status & ADM5120_DMA_FCSERR) {
+			priv->stats.rx_errors++;
+			skbn = NULL;
+		} else {
+			skbn = dev_alloc_skb(ADM5120_DMA_RXSIZE+16);
+			if (skbn) {
+				skb_put(skb, len);
+				skb->dev = dev;
+				skb->protocol = eth_type_trans(skb, dev);
+				skb->ip_summed = CHECKSUM_UNNECESSARY;
+				dev->last_rx = jiffies;
+				priv->stats.rx_packets++;
+				priv->stats.rx_bytes+=len;
+				skb_reserve(skbn, 2);
+				skbl[*index] = skbn;
+			} else {
+				printk(KERN_INFO "%s recycling!\n", dev->name);
+			}
+		}
+
+		dma[*index].status = 0;
+		dma[*index].cntl = 0;
+		dma[*index].len = ADM5120_DMA_RXSIZE;
+		dma[*index].data = ADM5120_DMA_ADDR(skbl[*index]->data) |
+		     ADM5120_DMA_OWN |
+		     (num-1==*index ? ADM5120_DMA_RINGEND : 0);
+		if (num == ++*index)
+			*index = 0;
+		if (skbn)
+			netif_rx(skb);
+	}
+}
+
+static inline void adm5120_tx(struct adm5120_dma *dma, struct sk_buff **skbl,
+    int *index, int num)
+{
+	while((dma[*index].data & ADM5120_DMA_OWN) == 0 && skbl[*index]) {
+		dev_kfree_skb_irq(skbl[*index]);
+		skbl[*index] = NULL;
+		if (++*index == num)
+			*index = 0;
+	}
+}
+
+irqreturn_t adm5120_sw_irq(int irq, void *dev_id, struct pt_regs *regs)
+{
+	unsigned long intreg;
+
+	adm5120_set_reg(ADM5120_INT_MASK,
+	    adm5120_get_reg(ADM5120_INT_MASK) | ADM5120_INTHANDLE);
+
+	intreg = adm5120_get_reg(ADM5120_INT_ST);
+	adm5120_set_reg(ADM5120_INT_ST, intreg);
+
+	if (intreg & ADM5120_INT_RXH)
+		adm5120_rx(adm5120_dma_rxh, adm5120_skb_rxh, &adm5120_rxhi,
+		ADM5120_DMA_RXH);
+	if (intreg & ADM5120_INT_HFULL)
+		adm5120_rxfixup(adm5120_dma_rxh, adm5120_skb_rxh,
+		ADM5120_DMA_RXH);
+	if (intreg & ADM5120_INT_RXL)
+		adm5120_rx(adm5120_dma_rxl, adm5120_skb_rxl, &adm5120_rxli,
+		    ADM5120_DMA_RXL);
+	if (intreg & ADM5120_INT_LFULL)
+		adm5120_rxfixup(adm5120_dma_rxl, adm5120_skb_rxl,
+		ADM5120_DMA_RXL);
+	if (intreg & ADM5120_INT_TXH)
+		adm5120_tx(adm5120_dma_txh, adm5120_skb_txh, &adm5120_txhit,
+		ADM5120_DMA_TXH);
+	if (intreg & ADM5120_INT_TXL)
+		adm5120_tx(adm5120_dma_txl, adm5120_skb_txl, &adm5120_txlit,
+		ADM5120_DMA_TXL);
+
+	adm5120_set_reg(ADM5120_INT_MASK,
+	    adm5120_get_reg(ADM5120_INT_MASK) & ~ADM5120_INTHANDLE);
+
+	return IRQ_HANDLED;
+}
+
+static void adm5120_set_vlan(char *matrix)
+{
+	unsigned long val;
+
+	val = matrix[0] + (matrix[1]<<8) + (matrix[2]<<16) + (matrix[3]<<24);
+	adm5120_set_reg(ADM5120_VLAN_GI, val);
+	val = matrix[4] + (matrix[5]<<8);
+	adm5120_set_reg(ADM5120_VLAN_GII, val);
+}
+
+static int adm5120_sw_open(struct net_device *dev)
+{
+	if (!adm5120_if_open++)
+		adm5120_set_reg(ADM5120_INT_MASK,
+		    adm5120_get_reg(ADM5120_INT_MASK) & ~ADM5120_INTHANDLE);
+	netif_start_queue(dev);
+	return 0;
+}
+
+static int adm5120_sw_stop(struct net_device *dev)
+{
+	netif_stop_queue(dev);
+	if (!--adm5120_if_open)
+		adm5120_set_reg(ADM5120_INT_MASK,
+		    adm5120_get_reg(ADM5120_INT_MASK) | ADM5120_INTMASKALL);
+	return 0;
+}
+
+static int adm5120_sw_tx(struct sk_buff *skb, struct net_device *dev)
+{
+	struct adm5120_dma *dma = adm5120_dma_txl;
+	struct sk_buff **skbl = adm5120_skb_txl;
+	struct adm5120_sw *priv = netdev_priv(dev);
+	int *index = &adm5120_txli;
+	int num = ADM5120_DMA_TXL;
+	int trigger = ADM5120_SEND_TRIG_L;
+
+	dev->trans_start = jiffies;
+	if (dma[*index].data & ADM5120_DMA_OWN) {
+		dev_kfree_skb(skb);
+		priv->stats.tx_dropped++;
+		return 0;
+	}
+
+	dma[*index].data = ADM5120_DMA_ADDR(skb->data) | ADM5120_DMA_OWN;
+	if (*index == num-1)
+		dma[*index].data |= ADM5120_DMA_RINGEND;
+	dma[*index].status =
+	    ((skb->len<ETH_ZLEN?ETH_ZLEN:skb->len) << ADM5120_DMA_LENSHIFT) |
+	    (0x1 << priv->port);
+	dma[*index].len = skb->len < ETH_ZLEN ? ETH_ZLEN : skb->len;
+	priv->stats.tx_packets++;
+	priv->stats.tx_bytes += skb->len;
+	skbl[*index]=skb;
+
+	if (++*index == num)
+		*index = 0;
+	adm5120_set_reg(ADM5120_SEND_TRIG, trigger);
+
+	return 0;
+}
+
+static void adm5120_tx_timeout(struct net_device *dev)
+{
+	netif_wake_queue(dev);
+}
+
+static struct net_device_stats *adm5120_sw_stats(struct net_device *dev)
+{
+	return &((struct adm5120_sw *)netdev_priv(dev))->stats;
+}
+
+static void adm5120_set_multicast_list(struct net_device *dev)
+{
+	struct adm5120_sw *priv = netdev_priv(dev);
+	int portmask;
+
+	portmask = vlan_matrix[priv->port] & 0x3f;
+
+	if (dev->flags & IFF_PROMISC)
+		adm5120_set_reg(ADM5120_CPUP_CONF,
+		    adm5120_get_reg(ADM5120_CPUP_CONF) &
+		    ~((portmask << ADM5120_DISUNSHIFT) & ADM5120_DISUNALL));
+	else
+		adm5120_set_reg(ADM5120_CPUP_CONF,
+		    adm5120_get_reg(ADM5120_CPUP_CONF) |
+		    (portmask << ADM5120_DISUNSHIFT));
+
+	if (dev->flags & IFF_PROMISC || dev->flags & IFF_ALLMULTI ||
+	    dev->mc_count)
+		adm5120_set_reg(ADM5120_CPUP_CONF,
+		    adm5120_get_reg(ADM5120_CPUP_CONF) &
+		    ~((portmask << ADM5120_DISMCSHIFT) & ADM5120_DISMCALL));
+	else
+		adm5120_set_reg(ADM5120_CPUP_CONF,
+		    adm5120_get_reg(ADM5120_CPUP_CONF) |
+		    (portmask << ADM5120_DISMCSHIFT));
+}
+
+static void adm5120_write_mac(struct net_device *dev)
+{
+	struct adm5120_sw *priv = netdev_priv(dev);
+	unsigned char *mac = dev->dev_addr;
+
+	adm5120_set_reg(ADM5120_MAC_WT1,
+	    mac[2] | (mac[3]<<8) | (mac[4]<<16) | (mac[5]<<24));
+	adm5120_set_reg(ADM5120_MAC_WT0, (priv->port<<3) |
+	    (mac[0]<<16) | (mac[1]<<24) | ADM5120_MAC_WRITE | ADM5120_VLAN_EN);
+
+	while (!(adm5120_get_reg(ADM5120_MAC_WT0) & ADM5120_MAC_WRITE_DONE));
+}
+
+static int adm5120_sw_set_mac_address(struct net_device *dev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
+	adm5120_write_mac(dev);
+	return 0;
+}
+
+static int adm5120_do_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+	int err;
+	struct adm5120_info info;
+	struct adm5120_sw *priv = netdev_priv(dev);
+
+	switch(cmd) {
+		case SIOCGADMINFO:
+			info.magic = 0x5120;
+			info.ports = adm5120_nrdevs;
+			info.vlan = priv->port;
+			err = copy_to_user(rq->ifr_data, &info, sizeof(info));
+			if (err)
+				return -EFAULT;
+			break;
+		case SIOCSMATRIX:
+			if (!capable(CAP_NET_ADMIN))
+				return -EPERM;
+			err = copy_from_user(vlan_matrix, rq->ifr_data,
+			    sizeof(vlan_matrix));
+			if (err)
+				return -EFAULT;
+			adm5120_set_vlan(vlan_matrix);
+			break;
+		case SIOCGMATRIX:
+			err = copy_to_user(rq->ifr_data, vlan_matrix,
+			    sizeof(vlan_matrix));
+			if (err)
+				return -EFAULT;
+			break;
+		default:
+			return -EOPNOTSUPP;
+	}
+	return 0;
+}
+
+static void adm5120_dma_tx_init(struct adm5120_dma *dma, struct sk_buff **skb,
+    int num)
+{
+	memset(dma, 0, sizeof(struct adm5120_dma)*num);
+	dma[num-1].data |= ADM5120_DMA_RINGEND;
+	memset(skb, 0, sizeof(struct skb*)*num);
+}
+
+static void adm5120_dma_rx_init(struct adm5120_dma *dma, struct sk_buff **skb,
+    int num)
+{
+	int i;
+
+	memset(dma, 0, sizeof(struct adm5120_dma)*num);
+	for (i=0; i<num; i++) {
+		skb[i] = dev_alloc_skb(ADM5120_DMA_RXSIZE+16);
+		if (!skb[i]) {
+			i=num;
+			break;
+		}
+		skb_reserve(skb[i], 2);
+		dma[i].data = ADM5120_DMA_ADDR(skb[i]->data) | ADM5120_DMA_OWN;
+		dma[i].cntl = 0;
+		dma[i].len = ADM5120_DMA_RXSIZE;
+		dma[i].status = 0;
+	}
+	dma[i-1].data |= ADM5120_DMA_RINGEND;
+}
+
+static int __init adm5120_sw_init(void)
+{
+	int i, err;
+	struct net_device *dev;
+
+	err = request_irq(SW_IRQ, adm5120_sw_irq, 0, "ethernet switch", NULL);
+	if (err)
+		goto out;
+
+	/* MII port? */
+	if (adm5120_get_reg(ADM5120_CODE) & ADM5120_CODE_PQFP)
+		adm5120_nrdevs = 5;
+	else
+		adm5120_nrdevs = 6;
+
+	adm5120_set_reg(ADM5120_CPUP_CONF,
+	    ADM5120_DISCCPUPORT | ADM5120_CRC_PADDING |
+	    ADM5120_DISUNALL | ADM5120_DISMCALL);
+	adm5120_set_reg(ADM5120_PORT_CONF0, ADM5120_ENMC | ADM5120_ENBP);
+
+	adm5120_set_reg(ADM5120_PHY_CNTL2, adm5120_get_reg(ADM5120_PHY_CNTL2) |
+	    ADM5120_AUTONEG | ADM5120_NORMAL | ADM5120_AUTOMDIX);
+	adm5120_set_reg(ADM5120_PHY_CNTL3, adm5120_get_reg(ADM5120_PHY_CNTL3) |
+	    ADM5120_PHY_NTH);
+
+	adm5120_set_reg(ADM5120_INT_MASK, ADM5120_INTMASKALL);
+	adm5120_set_reg(ADM5120_INT_ST, ADM5120_INTMASKALL);
+
+	adm5120_dma_txh = (void *)KSEG1ADDR((u32)adm5120_dma_txh_v);
+	adm5120_dma_txl = (void *)KSEG1ADDR((u32)adm5120_dma_txl_v);
+	adm5120_dma_rxh = (void *)KSEG1ADDR((u32)adm5120_dma_rxh_v);
+	adm5120_dma_rxl = (void *)KSEG1ADDR((u32)adm5120_dma_rxl_v);
+
+	adm5120_dma_tx_init(adm5120_dma_txh, adm5120_skb_txh, ADM5120_DMA_TXH);
+	adm5120_dma_tx_init(adm5120_dma_txl, adm5120_skb_txl, ADM5120_DMA_TXL);
+	adm5120_dma_rx_init(adm5120_dma_rxh, adm5120_skb_rxh, ADM5120_DMA_RXH);
+	adm5120_dma_rx_init(adm5120_dma_rxl, adm5120_skb_rxl, ADM5120_DMA_RXL);
+	adm5120_set_reg(ADM5120_SEND_HBADDR, KSEG1ADDR(adm5120_dma_txh));
+	adm5120_set_reg(ADM5120_SEND_LBADDR, KSEG1ADDR(adm5120_dma_txl));
+	adm5120_set_reg(ADM5120_RECEIVE_HBADDR, KSEG1ADDR(adm5120_dma_rxh));
+	adm5120_set_reg(ADM5120_RECEIVE_LBADDR, KSEG1ADDR(adm5120_dma_rxl));
+
+	adm5120_set_vlan(vlan_matrix);
+	
+	for (i=0; i<adm5120_nrdevs; i++) {
+		adm5120_devs[i] = alloc_etherdev(sizeof(struct adm5120_sw));
+		if (!adm5120_devs[i]) {
+			err = -ENOMEM;
+			goto out_int;
+		}
+		
+		dev = adm5120_devs[i];
+		SET_MODULE_OWNER(dev);
+		memset(netdev_priv(dev), 0, sizeof(struct adm5120_sw));
+		((struct adm5120_sw*)netdev_priv(dev))->port = i;
+		dev->base_addr = SW_BASE;
+		dev->irq = SW_IRQ;
+		dev->open = adm5120_sw_open;
+		dev->hard_start_xmit = adm5120_sw_tx;
+		dev->stop = adm5120_sw_stop;
+		dev->get_stats = adm5120_sw_stats;
+		dev->set_multicast_list = adm5120_set_multicast_list;
+		dev->do_ioctl = adm5120_do_ioctl;
+		dev->tx_timeout = adm5120_tx_timeout;
+		dev->watchdog_timeo = ETH_TX_TIMEOUT;
+		dev->set_mac_address = adm5120_sw_set_mac_address;
+		/* HACK alert!!!  In the original admtek driver it is asumed
+		   that you can read the MAC addressess from flash, but edimax
+		   decided to leave that space intentionally blank...
+		 */
+		memcpy(dev->dev_addr, "\x00\x50\xfc\x11\x22\x01", 6);
+		dev->dev_addr[5] += i;
+		adm5120_write_mac(dev);
+		
+		if ((err = register_netdev(dev))) {
+			free_netdev(dev);
+			goto out_int;
+		}
+		printk(KERN_INFO "%s: ADM5120 switch port%d\n", dev->name, i);
+	}
+	adm5120_set_reg(ADM5120_CPUP_CONF,
+	    ADM5120_CRC_PADDING | ADM5120_DISUNALL | ADM5120_DISMCALL);
+
+	return 0;
+
+out_int:
+	/* Undo everything that did succeed */
+	for (; i; i--) {
+		unregister_netdev(adm5120_devs[i-1]);
+		free_netdev(adm5120_devs[i-1]);
+	}
+	free_irq(SW_IRQ, NULL);
+out:
+	printk(KERN_ERR "ADM5120 Ethernet switch init failed\n");
+	return err;
+}
+
+static void __exit adm5120_sw_exit(void)
+{
+	int i;
+
+	for (i = 0; i < adm5120_nrdevs; i++) {
+		unregister_netdev(adm5120_devs[i]);
+		free_netdev(adm5120_devs[i-1]);
+	}
+
+	free_irq(SW_IRQ, NULL);
+
+	for (i = 0; i < ADM5120_DMA_RXH; i++) {
+		if (!adm5120_skb_rxh[i])
+			break;
+		kfree_skb(adm5120_skb_rxh[i]);
+	}
+	for (i = 0; i < ADM5120_DMA_RXL; i++) {
+		if (!adm5120_skb_rxl[i])
+			break;
+		kfree_skb(adm5120_skb_rxl[i]);
+	}
+}
+
+module_init(adm5120_sw_init);
+module_exit(adm5120_sw_exit);
diff --git a/target/linux/adm5120-2.6/files/drivers/net/adm5120sw.h b/target/linux/adm5120-2.6/files/drivers/net/adm5120sw.h
new file mode 100644
index 0000000000..4ea1e6257c
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/drivers/net/adm5120sw.h
@@ -0,0 +1,106 @@
+/*
+ *	Defines for ADM5120 built in ethernet switch driver
+ *
+ *	Copyright Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ *
+ *	Values come from ADM5120 datasheet and original ADMtek 2.4 driver,
+ *	Copyright ADMtek Inc.
+ */
+
+#ifndef _INCLUDE_ADM5120SW_H_
+#define _INCLUDE_ADM5120SW_H_
+
+#define SW_BASE	KSEG1ADDR(0x12000000)
+#define SW_DEVS	6
+#define SW_IRQ 	9
+
+#define ETH_TX_TIMEOUT	HZ/4
+#define ETH_FCS 4;
+
+#define ADM5120_CODE		0x00		/* CPU description */
+#define ADM5120_CODE_PQFP	0x20000000	/* package type */
+#define ADM5120_CPUP_CONF	0x24		/* CPU port config */
+#define ADM5120_DISCCPUPORT	0x00000001	/* disable cpu port */
+#define ADM5120_CRC_PADDING	0x00000002	/* software crc */
+#define ADM5120_DISUNSHIFT	9
+#define ADM5120_DISUNALL	0x00007e00	/* disable unknown from all */
+#define ADM5120_DISMCSHIFT	16
+#define ADM5120_DISMCALL	0x003f0000	/* disable multicast from all */
+#define ADM5120_PORT_CONF0	0x28
+#define ADM5120_ENMC		0x00003f00	/* Enable MC routing (ex cpu) */
+#define ADM5120_ENBP		0x003f0000	/* Enable Back Pressure */
+#define ADM5120_VLAN_GI		0x40		/* VLAN settings */
+#define ADM5120_VLAN_GII	0x44
+#define ADM5120_SEND_TRIG	0x48
+#define ADM5120_SEND_TRIG_L	0x00000001
+#define ADM5120_SEND_TRIG_H	0x00000002
+#define ADM5120_MAC_WT0		0x58
+#define ADM5120_MAC_WRITE	0x00000001
+#define ADM5120_MAC_WRITE_DONE	0x00000002
+#define ADM5120_VLAN_EN		0x00000040
+#define ADM5120_MAC_WT1		0x5c
+#define ADM5120_PHY_CNTL2	0x7c
+#define ADM5120_AUTONEG		0x0000001f	/* Auto negotiate */
+#define ADM5120_NORMAL		0x01f00000	/* PHY normal mode */
+#define ADM5120_AUTOMDIX	0x3e000000	/* Auto MDIX */
+#define ADM5120_PHY_CNTL3	0x80
+#define ADM5120_PHY_NTH		0x00000400
+#define ADM5120_INT_ST		0xb0
+#define ADM5120_INT_RXH		0x0000004
+#define ADM5120_INT_RXL		0x0000008
+#define ADM5120_INT_HFULL	0x0000010
+#define ADM5120_INT_LFULL	0x0000020
+#define ADM5120_INT_TXH		0x0000001
+#define ADM5120_INT_TXL		0x0000002
+#define ADM5120_INT_MASK	0xb4
+#define ADM5120_INTMASKALL	0x1FDEFFF	/* All interrupts */
+#define ADM5120_INTHANDLE	(ADM5120_INT_RXH | ADM5120_INT_RXL | \
+				 ADM5120_INT_HFULL | ADM5120_INT_LFULL | \
+				 ADM5120_INT_TXH | ADM5120_INT_TXL)
+#define ADM5120_SEND_HBADDR	0xd0
+#define ADM5120_SEND_LBADDR	0xd4
+#define ADM5120_RECEIVE_HBADDR	0xd8
+#define ADM5120_RECEIVE_LBADDR	0xdc
+
+struct adm5120_dma {
+	u32 data;
+	u32 cntl;
+	u32 len;
+	u32 status;
+} __attribute__ ((packed));
+
+#define	ADM5120_DMA_MASK	0x00ffffff
+#define ADM5120_DMA_OWN		0x80000000	/* buffer owner */
+#define ADM5120_DMA_RINGEND	0x10000000	/* Last in DMA ring */
+
+#define ADM5120_DMA_ADDR(ptr)	((u32)(ptr) & ADM5120_DMA_MASK)
+#define ADM5120_DMA_PORTID	0x00007000
+#define ADM5120_DMA_PORTSHIFT	12
+#define ADM5120_DMA_LEN		0x07ff0000
+#define ADM5120_DMA_LENSHIFT	16
+#define ADM5120_DMA_FCSERR	0x00000008
+
+#define ADM5120_DMA_TXH		16
+#define ADM5120_DMA_TXL		64
+#define ADM5120_DMA_RXH		16
+#define ADM5120_DMA_RXL		8
+
+#define ADM5120_DMA_RXSIZE	1550
+#define ADM5120_DMA_EXTRA	20
+
+struct adm5120_sw {
+	int			port;
+	struct net_device_stats	stats;
+};
+
+#define SIOCSMATRIX	SIOCDEVPRIVATE
+#define SIOCGMATRIX	SIOCDEVPRIVATE+1
+#define SIOCGADMINFO	SIOCDEVPRIVATE+2
+
+struct adm5120_info {
+	u16	magic;
+	u16	ports;
+	u16	vlan;
+};
+
+#endif /* _INCLUDE_ADM5120SW_H_ */
diff --git a/target/linux/adm5120-2.6/files/drivers/serial/adm5120_uart.c b/target/linux/adm5120-2.6/files/drivers/serial/adm5120_uart.c
new file mode 100644
index 0000000000..cbbdbfb6ab
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/drivers/serial/adm5120_uart.c
@@ -0,0 +1,524 @@
+/*
+ *	Serial driver for ADM5120 SoC
+ *
+ *	Derived from drivers/serial/uart00.c
+ *	Copyright 2001 Altera Corporation
+ *
+ *	Some pieces are derived from the ADMtek 2.4 serial driver.
+ *	Copyright (C) ADMtek Incorporated, 2003
+ *		daniell@admtek.com.tw
+ *	Which again was derived from drivers/char/serial.c
+ *	Copyright (C) Linus Torvalds et al.
+ *
+ *	Copyright Jeroen Vreeken (pe1rxq@amsat.org), 2005
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/console.h>
+
+#define ADM5120_UART_BASE0		0x12600000
+#define ADM5120_UART_BASE1		0x12800000
+#define ADM5120_UART_SIZE		0x20
+
+#define ADM5120_UART_IRQ0		1
+#define ADM5120_UART_IRQ1		2
+
+#define ADM5120_UART_REG(base, reg) \
+	(*(volatile u32 *)KSEG1ADDR((base)+(reg)))
+
+#define ADM5120_UARTCLK_FREQ            62500000
+#define ADM5120_UART_BAUDDIV(rate)	((unsigned long)(ADM5120_UARTCLK_FREQ/(16*(_rate)) - 1))
+
+#define ADM5120_UART_BAUD115200		ADM5120_UART_BAUDDIV(115200)
+
+#define ADM5120_UART_DATA		0x00
+#define ADM5120_UART_RS			0x04
+#define ADM5120_UART_LCR_H		0x08
+#define ADM5120_UART_LCR_M		0x0c
+#define ADM5120_UART_LCR_L		0x10
+#define ADM5120_UART_CR			0x14
+#define ADM5120_UART_FR			0x18
+#define ADM5120_UART_IR			0x1c
+
+#define ADM5120_UART_FE			0x01
+#define ADM5120_UART_PE			0x02
+#define ADM5120_UART_BE			0x04
+#define ADM5120_UART_OE			0x08
+#define ADM5120_UART_ERR		0x0f
+#define ADM5120_UART_FIFO_EN		0x10
+#define ADM5120_UART_EN			0x01
+#define ADM5120_UART_TIE		0x20
+#define ADM5120_UART_RIE		0x50
+#define ADM5120_UART_IE			0x78
+#define ADM5120_UART_CTS		0x01
+#define ADM5120_UART_DSR		0x02
+#define ADM5120_UART_DCD		0x04
+#define ADM5120_UART_TXFF		0x20
+#define ADM5120_UART_TXFE		0x80
+#define ADM5120_UART_RXFE		0x10
+#define ADM5120_UART_BRK		0x01
+#define ADM5120_UART_PEN		0x02
+#define ADM5120_UART_EPS		0x04
+#define ADM5120_UART_STP2		0x08
+#define ADM5120_UART_W5			0x00
+#define ADM5120_UART_W6			0x20
+#define ADM5120_UART_W7			0x40
+#define ADM5120_UART_W8			0x60
+#define ADM5120_UART_MIS		0x01
+#define ADM5120_UART_RIS		0x02
+#define ADM5120_UART_TIS		0x04
+#define ADM5120_UART_RTIS		0x08
+
+static void adm5120ser_stop_tx(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) &= ~ADM5120_UART_TIE;
+}
+
+static void adm5120ser_irq_rx(struct uart_port *port)
+{
+	struct tty_struct *tty = port->info->tty;
+	unsigned int status, ch, rds, flg, ignored = 0;
+
+	status = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+	while (!(status & ADM5120_UART_RXFE)) {
+		/* 
+		 * We need to read rds before reading the 
+		 * character from the fifo
+		 */
+		rds = ADM5120_UART_REG(port->iobase, ADM5120_UART_RS);
+		ch = ADM5120_UART_REG(port->iobase, ADM5120_UART_DATA);
+		port->icount.rx++;
+
+		if (tty->low_latency)
+			tty_flip_buffer_push(tty);
+
+		flg = TTY_NORMAL;
+
+		/*
+		 * Note that the error handling code is
+		 * out of the main execution path
+		 */
+		if (rds & ADM5120_UART_ERR)
+			goto handle_error;
+		if (uart_handle_sysrq_char(port, ch))
+			goto ignore_char;
+
+	error_return:
+		tty_insert_flip_char(tty, ch, flg);
+
+	ignore_char:
+		status = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+	}
+ out:
+	tty_flip_buffer_push(tty);
+	return;
+
+ handle_error:
+ 	ADM5120_UART_REG(port->iobase, ADM5120_UART_RS) = 0xff;
+	if (rds & ADM5120_UART_BE) {
+		port->icount.brk++;
+		if (uart_handle_break(port))
+			goto ignore_char;
+	} else if (rds & ADM5120_UART_PE)
+		port->icount.parity++;
+	else if (rds & ADM5120_UART_FE)
+		port->icount.frame++;
+	if (rds & ADM5120_UART_OE)
+		port->icount.overrun++;
+
+	if (rds & port->ignore_status_mask) {
+		if (++ignored > 100)
+			goto out;
+		goto ignore_char;
+	}
+	rds &= port->read_status_mask;
+
+	if (rds & ADM5120_UART_BE)
+		flg = TTY_BREAK;
+	else if (rds & ADM5120_UART_PE)
+		flg = TTY_PARITY;
+	else if (rds & ADM5120_UART_FE)
+		flg = TTY_FRAME;
+
+	if (rds & ADM5120_UART_OE) {
+		/*
+		 * CHECK: does overrun affect the current character?
+		 * ASSUMPTION: it does not.
+		 */
+		tty_insert_flip_char(tty, ch, flg);
+		ch = 0;
+		flg = TTY_OVERRUN;
+	}
+#ifdef CONFIG_MAGIC_SYSRQ
+	port->sysrq = 0;
+#endif
+	goto error_return;
+}
+
+static void adm5120ser_irq_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->info->xmit;
+	int count;
+
+	if (port->x_char) {
+		ADM5120_UART_REG(port->iobase, ADM5120_UART_DATA) =
+		    port->x_char;
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		adm5120ser_stop_tx(port);
+		return;
+	}
+
+	count = port->fifosize >> 1;
+	do {
+		ADM5120_UART_REG(port->iobase, ADM5120_UART_DATA) =
+		    xmit->buf[xmit->tail];
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	} while (--count > 0);
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		adm5120ser_stop_tx(port);
+}
+
+static void adm5120ser_irq_modem(struct uart_port *port)
+{
+	unsigned int status;
+
+	status = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+
+	if (status & ADM5120_UART_DCD)
+		uart_handle_dcd_change(port, status & ADM5120_UART_DCD);
+
+	if (status & ADM5120_UART_DSR)
+		port->icount.dsr++;
+
+	if (status & ADM5120_UART_CTS)
+		uart_handle_cts_change(port, status & ADM5120_UART_CTS);
+
+	wake_up_interruptible(&port->info->delta_msr_wait);
+}
+
+static irqreturn_t adm5120ser_irq(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	unsigned long ir = ADM5120_UART_REG(port->iobase, ADM5120_UART_IR);
+
+	if (ir & (ADM5120_UART_RIS | ADM5120_UART_RTIS))
+		adm5120ser_irq_rx(port);
+	if (ir & ADM5120_UART_TIS)
+		adm5120ser_irq_tx(port);
+	if (ir & ADM5120_UART_MIS) {
+		adm5120ser_irq_modem(port);
+		ADM5120_UART_REG(port->iobase, ADM5120_UART_IR) = 0xff;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static unsigned int adm5120ser_tx_empty(struct uart_port *port)
+{
+	unsigned int fr = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+	return (fr & ADM5120_UART_TXFE) ? TIOCSER_TEMT : 0;
+}
+
+static void adm5120ser_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int adm5120ser_get_mctrl(struct uart_port *port)
+{
+	unsigned int result = 0;
+	unsigned int fr = ADM5120_UART_REG(port->iobase, ADM5120_UART_FR);
+
+	if (fr & ADM5120_UART_CTS)
+		result |= TIOCM_CTS;
+	if (fr & ADM5120_UART_DSR)
+		result |= TIOCM_DSR;
+	if (fr & ADM5120_UART_DCD)
+		result |= TIOCM_CAR;
+	return result;
+}
+
+static void adm5120ser_start_tx(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) |= ADM5120_UART_TIE;
+}
+
+static void adm5120ser_stop_rx(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) &= ~ADM5120_UART_RIE;
+}
+
+static void adm5120ser_enable_ms(struct uart_port *port)
+{
+}
+
+static void adm5120ser_break_ctl(struct uart_port *port, int break_state)
+{
+	unsigned long flags;
+	unsigned long lcrh;
+
+	spin_lock_irqsave(&port->lock, flags);
+	lcrh = ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H);
+	if (break_state == -1)
+		lcrh |= ADM5120_UART_BRK;
+	else
+		lcrh &= ~ADM5120_UART_BRK;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H) = lcrh;
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int adm5120ser_startup(struct uart_port *port)
+{
+	int ret;
+
+	ret = request_irq(port->irq, adm5120ser_irq, 0, "ADM5120 UART", port);
+	if (ret) {
+		printk(KERN_ERR "Couldn't get irq %d\n", port->irq);
+		return ret;
+	}
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H) |=
+	    ADM5120_UART_FIFO_EN;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) |=
+	    ADM5120_UART_EN | ADM5120_UART_IE;
+	return 0;
+}
+
+static void adm5120ser_shutdown(struct uart_port *port)
+{
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_CR) &= ~ADM5120_UART_IE;
+	free_irq(port->irq, port);
+}
+
+static void adm5120ser_set_termios(struct uart_port *port,
+    struct termios *termios, struct termios *old)
+{
+	unsigned int baud, quot, lcrh;
+	unsigned long flags;
+
+	termios->c_cflag |= CREAD;
+
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+	quot = uart_get_divisor(port, baud);
+
+	lcrh = ADM5120_UART_FIFO_EN;
+	switch (termios->c_cflag & CSIZE) {
+		case CS5:
+			lcrh |= ADM5120_UART_W5;
+			break;
+		case CS6:
+			lcrh |= ADM5120_UART_W6;
+			break;
+		case CS7:
+			lcrh |= ADM5120_UART_W7;
+			break;
+		default:
+			lcrh |= ADM5120_UART_W8;
+			break;
+	}
+	if (termios->c_cflag & CSTOPB)
+		lcrh |= ADM5120_UART_STP2;
+	if (termios->c_cflag & PARENB) {
+		lcrh |= ADM5120_UART_PEN;
+		if (!(termios->c_cflag & PARODD))
+			lcrh |= ADM5120_UART_EPS;
+	}
+
+	spin_lock_irqsave(port->lock, flags);
+
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_H) = lcrh;
+
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	port->read_status_mask = ADM5120_UART_OE;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= ADM5120_UART_FE | ADM5120_UART_PE;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= ADM5120_UART_BE;
+
+	/*
+	 * Characters to ignore
+	 */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= ADM5120_UART_FE | ADM5120_UART_PE;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= ADM5120_UART_BE;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns to (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= ADM5120_UART_OE;
+	}
+
+	quot = ADM5120_UART_BAUD115200;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_L) = quot & 0xff;
+	ADM5120_UART_REG(port->iobase, ADM5120_UART_LCR_M) = quot >> 8;
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *adm5120ser_type(struct uart_port *port)
+{
+	return port->type == PORT_ADM5120 ? "ADM5120" : NULL;
+}
+
+static void adm5120ser_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE)
+		port->type = PORT_ADM5120;
+}
+
+static void adm5120ser_release_port(struct uart_port *port)
+{
+	release_mem_region(port->iobase, ADM5120_UART_SIZE);
+}
+
+static int adm5120ser_request_port(struct uart_port *port)
+{
+	return request_mem_region(port->iobase, ADM5120_UART_SIZE,
+	    "adm5120-uart") != NULL ? 0 : -EBUSY; 
+}
+
+static struct uart_ops adm5120ser_ops = {
+	.tx_empty =	adm5120ser_tx_empty,
+	.set_mctrl =	adm5120ser_set_mctrl,
+	.get_mctrl =	adm5120ser_get_mctrl,
+	.stop_tx =	adm5120ser_stop_tx,
+	.start_tx =	adm5120ser_start_tx,
+	.stop_rx =	adm5120ser_stop_rx,
+	.enable_ms =	adm5120ser_enable_ms,
+	.break_ctl =	adm5120ser_break_ctl,
+	.startup =	adm5120ser_startup,
+	.shutdown =	adm5120ser_shutdown,
+	.set_termios =	adm5120ser_set_termios,
+	.type =		adm5120ser_type,
+	.config_port =	adm5120ser_config_port,
+	.release_port =	adm5120ser_release_port,
+	.request_port =	adm5120ser_request_port,
+};
+
+static void adm5120console_put(const char c)
+{
+	while ((ADM5120_UART_REG(ADM5120_UART_BASE0, ADM5120_UART_FR) &
+	     ADM5120_UART_TXFF) != 0);
+	ADM5120_UART_REG(ADM5120_UART_BASE0, ADM5120_UART_DATA) = c;
+}
+
+static void adm5120console_write(struct console *con, const char *s,
+    unsigned int count)
+{
+	while (count--) {
+		if (*s == '\n')
+			adm5120console_put('\r');
+		adm5120console_put(*s);
+		s++;
+	}
+}
+
+static int __init adm5120console_setup(struct console *con, char *options)
+{
+	/* Set to 115200 baud, 8N1 and enable FIFO */
+	ADM5120_UART_REG(ADM5120_UART_BASE0, ADM5120_UART_LCR_L) =
+	    ADM5120_UART_BAUD115200 & 0xff;
+	ADM5120_UART_REG(ADM5120_UART_BASE0, ADM5120_UART_LCR_M) =
+	    ADM5120_UART_BAUD115200 >> 8;
+	ADM5120_UART_REG(ADM5120_UART_BASE0, ADM5120_UART_LCR_H) =
+	    ADM5120_UART_W8 | ADM5120_UART_FIFO_EN;
+	/* Enable port */
+	ADM5120_UART_REG(ADM5120_UART_BASE0, ADM5120_UART_CR) =
+	    ADM5120_UART_EN;
+
+	return 0;
+}
+
+static struct uart_driver adm5120ser_reg;
+
+static struct console adm5120_serconsole = {
+	.name =		"ttyS",
+	.write =	adm5120console_write,
+	.device =	uart_console_device,
+	.setup =	adm5120console_setup,
+	.flags =	CON_PRINTBUFFER,
+	.cflag =	B115200 | CS8 | CREAD,
+	.index =	0,
+	.data =		&adm5120ser_reg,
+};
+
+static int __init adm5120console_init(void)
+{
+	register_console(&adm5120_serconsole);
+	return 0;
+}
+
+console_initcall(adm5120console_init);
+
+
+static struct uart_port adm5120ser_ports[] = {
+	{
+		.iobase =	ADM5120_UART_BASE0,
+		.irq =		ADM5120_UART_IRQ0,
+		.uartclk =	ADM5120_UARTCLK_FREQ,
+		.fifosize =	16,
+		.ops =		&adm5120ser_ops,
+		.line =		0,
+		.flags =	ASYNC_BOOT_AUTOCONF,
+	},
+#if (CONFIG_ADM5120_NR_UARTS > 1)
+	{
+		.iobase =	ADM5120_UART_BASE1,
+		.irq =		ADM5120_UART_IRQ1,
+		.uartclk =	ADM5120_UARTCLK_FREQ,
+		.fifosize =	16,
+		.ops =		&adm5120ser_ops,
+		.line =		1,
+		.flags =	ASYNC_BOOT_AUTOCONF,
+	},
+#endif
+};
+
+static struct uart_driver adm5120ser_reg = {
+	.owner	=	THIS_MODULE,
+	.driver_name =	"ttyS",
+	.dev_name =	"ttyS",
+	.major =	TTY_MAJOR,
+	.minor =	64,
+	.nr =		CONFIG_ADM5120_NR_UARTS,
+	.cons =		&adm5120_serconsole,
+};
+
+static int __init adm5120ser_init(void)
+{
+	int ret, i;
+
+	ret = uart_register_driver(&adm5120ser_reg);
+	if (!ret) {
+		for (i = 0; i < CONFIG_ADM5120_NR_UARTS; i++)
+			uart_add_one_port(&adm5120ser_reg, &adm5120ser_ports[i]);
+	}
+
+	return ret;
+}
+
+__initcall(adm5120ser_init);
diff --git a/target/linux/adm5120-2.6/files/drivers/usb/host/adm5120-hcd.c b/target/linux/adm5120-2.6/files/drivers/usb/host/adm5120-hcd.c
new file mode 100644
index 0000000000..b4a1899d1d
--- /dev/null
+++ b/target/linux/adm5120-2.6/files/drivers/usb/host/adm5120-hcd.c
@@ -0,0 +1,790 @@
+/*
+ *	HCD driver for ADM5120 SoC
+ *
+ *	Copyright (C) 2005 Jeroen Vreeken (pe1rxq@amsat.org)
+ *
+ *	Based on the ADMtek 2.4 driver 
+ *	(C) Copyright 2003 Junius Chen <juniusc@admtek.com.tw>
+ *	Which again was based on the ohci and uhci drivers.
+ */
+
+#include <linux/autoconf.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/usb.h>
+#include <linux/platform_device.h>
+
+#include "../core/hcd.h"
+
+MODULE_DESCRIPTION("ADM5120 USB Host Controller Driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Jeroen Vreeken (pe1rxq@amsat.org)");
+
+#define ADMHCD_REG_CONTROL		0x00
+#define ADMHCD_REG_INTSTATUS		0x04
+#define ADMHCD_REG_INTENABLE		0x08
+#define ADMHCD_REG_HOSTCONTROL		0x10
+#define ADMHCD_REG_FMINTERVAL		0x18
+#define ADMHCD_REG_FMNUMBER		0x1c
+#define ADMHCD_REG_LSTHRESH		0x70
+#define ADMHCD_REG_RHDESCR		0x74
+#define ADMHCD_REG_PORTSTATUS0		0x78
+#define ADMHCD_REG_PORTSTATUS1		0x7c
+#define ADMHCD_REG_HOSTHEAD		0x80
+
+
+#define ADMHCD_NUMPORTS		2
+
+#define ADMHCD_HOST_EN		0x00000001	/* Host enable */
+#define ADMHCD_SW_INTREQ	0x00000002	/* request software int */
+#define ADMHCD_SW_RESET		0x00000008	/* Reset */
+
+#define ADMHCD_INT_TD		0x00100000	/* TD completed */
+#define ADMHCD_INT_SW		0x20000000	/* software interrupt */
+#define ADMHCD_INT_FATAL	0x40000000	/* Fatal interrupt */
+#define ADMHCD_INT_ACT		0x80000000	/* Interrupt active */
+
+#define ADMHCD_STATE_RST	0x00000000	/* bus state reset */
+#define ADMHCD_STATE_RES	0x00000001	/* bus state resume */
+#define ADMHCD_STATE_OP		0x00000002	/* bus state operational */
+#define ADMHCD_STATE_SUS	0x00000003	/* bus state suspended */
+#define ADMHCD_DMA_EN		0x00000004	/* enable dma engine */
+
+#define ADMHCD_NPS		0x00000020	/* No Power Switch */
+#define ADMHCD_LPSC		0x04000000	/* Local power switch change */
+
+#define ADMHCD_CCS		0x00000001	/* current connect status */
+#define ADMHCD_PES		0x00000002	/* port enable status */
+#define ADMHCD_PSS		0x00000004	/* port suspend status */
+#define ADMHCD_POCI		0x00000008	/* port overcurrent indicator */
+#define ADMHCD_PRS		0x00000010	/* port reset status */
+#define ADMHCD_PPS		0x00000100	/* port power status */
+#define ADMHCD_LSDA		0x00000200	/* low speed device attached */
+#define ADMHCD_CSC		0x00010000	/* connect status change */
+#define ADMHCD_PESC		0x00020000	/* enable status change */
+#define ADMHCD_PSSC		0x00040000	/* suspend status change */
+#define ADMHCD_OCIC		0x00080000	/* overcurrent change*/
+#define ADMHCD_PRSC		0x00100000	/* reset status change */
+
+
+struct admhcd_ed {
+	/* Don't change first four, they used for DMA */
+	u32				control;
+	struct admhcd_td		*tail;
+	struct admhcd_td		*head;
+	struct admhcd_ed		*next;
+	/* the rest is for the driver only: */
+	struct admhcd_td		*cur;
+	struct usb_host_endpoint 	*ep;
+	struct urb			*urb;
+	struct admhcd_ed		*real;
+} __attribute__ ((packed));
+
+#define ADMHCD_ED_EPSHIFT	7		/* Shift for endpoint number */
+#define ADMHCD_ED_INT		0x00000800	/* Is this an int endpoint */
+#define ADMHCD_ED_SPEED		0x00002000	/* Is it a high speed dev? */
+#define ADMHCD_ED_SKIP		0x00004000	/* Skip this ED */
+#define ADMHCD_ED_FORMAT	0x00008000	/* Is this an isoc endpoint */
+#define ADMHCD_ED_MAXSHIFT	16		/* Shift for max packet size */
+
+struct admhcd_td {
+	/* Don't change first four, they are used for DMA */
+	u32			control;
+	u32			buffer;
+	u32			buflen;
+	struct admhcd_td	*next;
+	/* the rest is for the driver only: */
+	struct urb		*urb;
+	struct admhcd_td	*real;
+} __attribute__ ((packed));
+
+#define ADMHCD_TD_OWN		0x80000000
+#define ADMHCD_TD_TOGGLE	0x00000000
+#define ADMHCD_TD_DATA0		0x01000000
+#define ADMHCD_TD_DATA1		0x01800000
+#define ADMHCD_TD_OUT		0x00200000
+#define ADMHCD_TD_IN		0x00400000
+#define ADMHCD_TD_SETUP		0x00000000
+#define ADMHCD_TD_ISO		0x00010000
+#define ADMHCD_TD_R		0x00040000
+#define ADMHCD_TD_INTEN		0x00010000
+
+static int admhcd_td_err[16] = {
+	0,		/* No */
+	-EREMOTEIO,		/* CRC */
+	-EREMOTEIO,	/* bit stuff */
+	-EREMOTEIO,		/* data toggle */
+	-EPIPE,		/* stall */
+	-ETIMEDOUT,	/* timeout */
+	-EPROTO,	/* pid err */
+	-EPROTO,	/* unexpected pid */
+	-EREMOTEIO,	/* data overrun */
+	-EREMOTEIO,	/* data underrun */
+	-ETIMEDOUT,	/* 1010 */
+	-ETIMEDOUT,	/* 1011 */
+	-EREMOTEIO,	/* buffer overrun */
+	-EREMOTEIO,	/* buffer underrun */
+	-ETIMEDOUT,	/* 1110 */
+	-ETIMEDOUT,	/* 1111 */
+};
+
+#define ADMHCD_TD_ERRMASK	0x38000000
+#define ADMHCD_TD_ERRSHIFT	27
+
+#define TD(td)	((struct admhcd_td *)(((u32)(td)) & ~0xf))
+#define ED(ed)	((struct admhcd_ed *)(((u32)(ed)) & ~0xf))
+
+struct admhcd {
+	u32		base;
+	u32		dma_en;
+	spinlock_t	lock;
+	unsigned long	flags;
+};
+
+#define hcd_to_admhcd(hcd) ((struct admhcd *)(hcd)->hcd_priv)
+
+static char hcd_name[] = "adm5120-hcd";
+
+static u32 admhcd_reg_get(struct admhcd *ahcd, int reg)
+{
+	return *(volatile u32 *)KSEG1ADDR(ahcd->base+reg);
+}
+
+static void admhcd_reg_set(struct admhcd *ahcd, int reg, u32 val)
+{
+	*(volatile u32 *)KSEG1ADDR(ahcd->base+reg) = val;
+}
+
+static void admhcd_lock(struct admhcd *ahcd)
+{
+	spin_lock_irqsave(&ahcd->lock, ahcd->flags);
+	ahcd->dma_en = admhcd_reg_get(ahcd, ADMHCD_REG_HOSTCONTROL) &
+	    ADMHCD_DMA_EN;
+	admhcd_reg_set(ahcd, ADMHCD_REG_HOSTCONTROL, ADMHCD_STATE_OP);
+}
+
+static void admhcd_unlock(struct admhcd *ahcd)
+{
+	admhcd_reg_set(ahcd, ADMHCD_REG_HOSTCONTROL,
+	    ADMHCD_STATE_OP | ahcd->dma_en);
+	spin_unlock_irqrestore(&ahcd->lock, ahcd->flags);
+}
+
+static struct admhcd_td *admhcd_td_alloc(struct admhcd_ed *ed, struct urb *urb)
+{
+	struct admhcd_td *tdn, *td;
+
+	tdn = kmalloc(sizeof(struct admhcd_td), GFP_ATOMIC);
+	if (!tdn)
+		return NULL;
+	tdn->real = tdn;
+	tdn = (struct admhcd_td *)KSEG1ADDR(tdn);
+	memset(tdn, 0, sizeof(struct admhcd_td));
+	if (ed->cur == NULL) {
+		ed->cur = tdn;
+		ed->head = tdn;
+		ed->tail = tdn;	
+		td = tdn;
+	} else {
+		/* Supply back the old tail and link in new td as tail */
+		td = TD(ed->tail);
+		TD(ed->tail)->next = tdn;
+		ed->tail = tdn;
+	}
+	td->urb = urb;
+
+	return td;
+}
+
+static void admhcd_td_free(struct admhcd_ed *ed, struct urb *urb)
+{
+	struct admhcd_td *td, **tdp;
+
+	if (urb == NULL)
+		ed->control |= ADMHCD_ED_SKIP;
+	tdp = &ed->cur;
+	td = ed->cur;
+	do {
+		if (td->urb == urb)
+			break;
+		tdp = &td->next;
+		td = TD(td->next);
+	} while (td);
+	while (td && td->urb == urb) {
+		*tdp = TD(td->next);
+		kfree(td->real);
+		td = *tdp;
+	}
+}
+
+/* Find an endpoint's descriptor, if needed allocate a new one and link it
+   in the DMA chain
+ */
+static struct admhcd_ed *admhcd_get_ed(struct admhcd *ahcd,
+    struct usb_host_endpoint *ep, struct urb *urb)
+{
+	struct admhcd_ed *hosthead;
+	struct admhcd_ed *found = NULL, *ed = NULL;
+	unsigned int pipe = urb->pipe;
+
+	admhcd_lock(ahcd);
+	hosthead = (struct admhcd_ed *)admhcd_reg_get(ahcd, ADMHCD_REG_HOSTHEAD);
+	if (hosthead) {
+		for (ed = hosthead;; ed = ED(ed->next)) {
+			if (ed->ep == ep) {
+				found = ed;
+				break;
+			}
+			if (ED(ed->next) == hosthead)
+				break;
+		}
+	}
+	if (!found) {
+		found = kmalloc(sizeof(struct admhcd_ed), GFP_ATOMIC);
+		if (!found)
+			goto out;
+		memset(found, 0, sizeof(struct admhcd_ed));
+		found->real = found;
+		found->ep = ep;
+		found = (struct admhcd_ed *)KSEG1ADDR(found);
+		found->control = usb_pipedevice(pipe) |
+		    (usb_pipeendpoint(pipe) << ADMHCD_ED_EPSHIFT) |
+		    (usb_pipeint(pipe) ? ADMHCD_ED_INT : 0) |
+		    (urb->dev->speed == USB_SPEED_FULL ? ADMHCD_ED_SPEED : 0) |
+		    (usb_pipeisoc(pipe) ? ADMHCD_ED_FORMAT : 0) |
+		    (usb_maxpacket(urb->dev, pipe, usb_pipeout(pipe)) << ADMHCD_ED_MAXSHIFT);
+		/* Alloc first dummy td */
+		admhcd_td_alloc(found, NULL);
+		if (hosthead) {
+			found->next = hosthead;
+			ed->next = found;
+		} else {
+			found->next = found;
+			admhcd_reg_set(ahcd, ADMHCD_REG_HOSTHEAD, (u32)found);
+		}
+	}
+out:
+	admhcd_unlock(ahcd);
+	return found;
+}
+
+static struct admhcd_td *admhcd_td_fill(u32 control, struct admhcd_td *td,
+    dma_addr_t data, int len)
+{
+	td->buffer = data;
+	td->buflen = len;
+	td->control = control;
+	return TD(td->next);
+}
+
+static void admhcd_ed_start(struct admhcd *ahcd, struct admhcd_ed *ed)
+{
+	struct admhcd_td *td = ed->cur;
+
+	if (ed->urb)
+		return;
+	if (td->urb) {
+		ed->urb = td->urb;
+		while (1) {
+			td->control |= ADMHCD_TD_OWN;
+			if (TD(td->next)->urb != td->urb) {
+				td->buflen |= ADMHCD_TD_INTEN;
+				break;
+			}
+			td = TD(td->next);
+		}
+	}
+	ed->head = TD(ed->head);
+	ahcd->dma_en |= ADMHCD_DMA_EN;
+}
+
+static irqreturn_t adm5120hcd_irq(int irq, void *ptr, struct pt_regs *regs)
+{
+	struct usb_hcd *hcd = (struct usb_hcd *)ptr;
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+	u32 intstatus;
+
+	intstatus = admhcd_reg_get(ahcd, ADMHCD_REG_INTSTATUS);
+	if (intstatus & ADMHCD_INT_FATAL) {
+		admhcd_reg_set(ahcd, ADMHCD_REG_INTSTATUS, ADMHCD_INT_FATAL);
+		//
+	}
+	if (intstatus & ADMHCD_INT_SW) {
+		admhcd_reg_set(ahcd, ADMHCD_REG_INTSTATUS, ADMHCD_INT_SW);
+		//
+	}
+	if (intstatus & ADMHCD_INT_TD) {
+		struct admhcd_ed *ed, *head;
+		
+		admhcd_reg_set(ahcd, ADMHCD_REG_INTSTATUS, ADMHCD_INT_TD);
+
+		head = (struct admhcd_ed *)admhcd_reg_get(ahcd, ADMHCD_REG_HOSTHEAD);
+		ed = head;
+		if (ed) do {
+			/* Is it a finished TD? */
+			if (ed->urb && !(ed->cur->control & ADMHCD_TD_OWN)) {
+				struct admhcd_td *td;
+				int error;
+				
+				td = ed->cur;
+				error = (td->control & ADMHCD_TD_ERRMASK) >>
+				    ADMHCD_TD_ERRSHIFT;
+				ed->urb->status = admhcd_td_err[error];
+				admhcd_td_free(ed, ed->urb);
+				// Calculate real length!!!
+				ed->urb->actual_length = ed->urb->transfer_buffer_length;
+				ed->urb->hcpriv = NULL;
+				usb_hcd_giveback_urb(hcd, ed->urb);
+				ed->urb = NULL;
+			}
+			admhcd_ed_start(ahcd, ed);
+			ed = ED(ed->next);
+		} while (ed != head);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int admhcd_urb_enqueue(struct usb_hcd *hcd, struct usb_host_endpoint *ep,
+    struct urb *urb, int mem_flags)
+{
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+	struct admhcd_ed *ed;
+	struct admhcd_td *td;
+	int size = 0, i, zero = 0, ret = 0;
+	unsigned int pipe = urb->pipe, toggle = 0;
+	dma_addr_t data = (dma_addr_t)urb->transfer_buffer;
+	int data_len = urb->transfer_buffer_length;
+
+	ed = admhcd_get_ed(ahcd, ep, urb);
+	if (!ed)
+		return -ENOMEM;
+
+	switch(usb_pipetype(pipe)) {
+		case PIPE_CONTROL:
+			size = 2;
+		case PIPE_INTERRUPT:
+		case PIPE_BULK:
+		default:
+			size += urb->transfer_buffer_length / 4096;
+			if (urb->transfer_buffer_length % 4096)
+				size++;
+			if (size == 0)
+				size++;
+			else if (urb->transfer_flags & URB_ZERO_PACKET &&
+			    !(urb->transfer_buffer_length %
+			      usb_maxpacket(urb->dev, pipe, usb_pipeout(pipe)))) {
+				size++;
+				zero = 1;
+			}
+			break;
+		case PIPE_ISOCHRONOUS:
+			size = urb->number_of_packets;
+			break;
+	}
+
+	admhcd_lock(ahcd);
+	/* Remember the first td */
+	td = admhcd_td_alloc(ed, urb);
+	if (!td) {
+		ret = -ENOMEM;
+		goto out;
+	}
+	/* Allocate additionall tds first */
+	for (i = 1; i < size; i++) {
+		if (admhcd_td_alloc(ed, urb) == NULL) {
+			admhcd_td_free(ed, urb);
+			ret = -ENOMEM;
+			goto out;
+		}
+	}
+
+	if (usb_gettoggle(urb->dev, usb_pipeendpoint(pipe), usb_pipeout(pipe)))
+		toggle = ADMHCD_TD_TOGGLE;
+	else {
+		toggle = ADMHCD_TD_DATA0;
+		usb_settoggle(urb->dev, usb_pipeendpoint(pipe),
+		    usb_pipeout(pipe), 1);
+	}
+
+	switch(usb_pipetype(pipe)) {
+		case PIPE_CONTROL:
+			td = admhcd_td_fill(ADMHCD_TD_SETUP | ADMHCD_TD_DATA0,
+			    td, (dma_addr_t)urb->setup_packet, 8);
+			while (data_len > 0) {
+				td = admhcd_td_fill(ADMHCD_TD_DATA1 
+				    | ADMHCD_TD_R |
+				    (usb_pipeout(pipe) ?
+				    ADMHCD_TD_OUT : ADMHCD_TD_IN), td,
+				    data, data_len % 4097);
+				data_len -= 4096;
+			}
+			admhcd_td_fill(ADMHCD_TD_DATA1 | (usb_pipeout(pipe) ?
+			    ADMHCD_TD_IN : ADMHCD_TD_OUT), td,
+			    data, 0);
+			break;
+		case PIPE_INTERRUPT:
+		case PIPE_BULK:
+			//info ok for interrupt?
+			i = 0;
+			while(data_len > 4096) {
+				td = admhcd_td_fill((usb_pipeout(pipe) ?
+				    ADMHCD_TD_OUT : 
+				    ADMHCD_TD_IN | ADMHCD_TD_R) |
+				    (i ? ADMHCD_TD_TOGGLE : toggle), td,
+				    data, 4096);
+				data += 4096;
+				data_len -= 4096;
+				i++;
+			}
+			td = admhcd_td_fill((usb_pipeout(pipe) ? 
+			    ADMHCD_TD_OUT : ADMHCD_TD_IN) |
+			    (i ? ADMHCD_TD_TOGGLE : toggle), td, data, data_len);
+			i++;
+			if (zero)
+				admhcd_td_fill((usb_pipeout(pipe) ?
+				    ADMHCD_TD_OUT : ADMHCD_TD_IN) |
+				    (i ? ADMHCD_TD_TOGGLE : toggle), td, 0, 0);
+			break;
+		case PIPE_ISOCHRONOUS:
+			for (i = 0; i < urb->number_of_packets; i++) {
+				td = admhcd_td_fill(ADMHCD_TD_ISO |
+				    ((urb->start_frame + i) & 0xffff), td,
+				    data + urb->iso_frame_desc[i].offset,
+				    urb->iso_frame_desc[i].length);
+			}
+			break;
+	}
+	urb->hcpriv = ed;
+	admhcd_ed_start(ahcd, ed);
+out:
+	admhcd_unlock(ahcd);
+	return ret;
+}
+
+static int admhcd_urb_dequeue(struct usb_hcd *hcd, struct urb *urb)
+{
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+	struct admhcd_ed *ed;
+
+	admhcd_lock(ahcd);
+
+	ed = urb->hcpriv;
+	if (ed && ed->urb != urb)
+		admhcd_td_free(ed, urb);
+
+	admhcd_unlock(ahcd);
+	return 0;
+}
+
+static void admhcd_endpoint_disable(struct usb_hcd *hcd, struct usb_host_endpoint *ep)
+{
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+	struct admhcd_ed *ed, *edt, *head;
+
+	admhcd_lock(ahcd);
+
+	head = (struct admhcd_ed *)admhcd_reg_get(ahcd, ADMHCD_REG_HOSTHEAD);
+	if (!head)
+		goto out;
+	for (ed = head; ED(ed->next) != head; ed = ED(ed->next))
+		if (ed->ep == ep)
+			break;
+	if (ed->ep != ep)
+		goto out;
+	while (ed->cur)
+		admhcd_td_free(ed, ed->cur->urb);
+	if (head == ed) {
+		if (ED(ed->next) == ed) {
+			admhcd_reg_set(ahcd, ADMHCD_REG_HOSTHEAD, 0);
+			ahcd->dma_en = 0;
+			goto out_free;
+		}
+		head = ED(ed->next);
+		for (edt = head; ED(edt->next) != head; edt = ED(edt->next));
+		edt->next = ED(ed->next);
+		admhcd_reg_set(ahcd, ADMHCD_REG_HOSTHEAD, (u32)ed->next);
+		goto out_free;
+	}
+	for (edt = head; edt->next != ed; edt = edt->next);
+	edt->next = ed->next;
+out_free:
+	kfree(ed->real);
+out:
+	admhcd_unlock(ahcd);
+}
+
+static int admhcd_get_frame_number(struct usb_hcd *hcd)
+{
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+
+	return admhcd_reg_get(ahcd, ADMHCD_REG_FMNUMBER) & 0x0000ffff;
+}
+
+static int admhcd_hub_status_data(struct usb_hcd *hcd, char *buf)
+{
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+	int port;
+
+	*buf = 0;
+	for (port = 0; port < ADMHCD_NUMPORTS; port++) {
+		if (admhcd_reg_get(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4) &
+		    (ADMHCD_CSC | ADMHCD_PESC | ADMHCD_PSSC | ADMHCD_OCIC |
+		     ADMHCD_PRSC))
+			*buf |= (1 << (port + 1));
+	}
+	return !!*buf;
+}
+
+static __u8 root_hub_hub_des[] = {
+	0x09,		/* __u8  bLength; */
+	0x29,		/* __u8  bDescriptorType; Hub-descriptor */
+	0x02,		/* __u8  bNbrPorts; */
+	0x0a, 0x00,	/* __u16 wHubCharacteristics; */
+	0x01,		/* __u8  bPwrOn2pwrGood; 2ms */
+	0x00,		/* __u8  bHubContrCurrent; 0mA */
+	0x00,		/* __u8  DeviceRemovable; */
+	0xff,		/* __u8  PortPwrCtrlMask; */
+};
+
+static int admhcd_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
+    u16 wIndex, char *buf, u16 wLength)
+{
+	struct admhcd *ahcd = hcd_to_admhcd(hcd);
+	int retval = 0, len;
+	unsigned int port = wIndex -1;
+
+	switch (typeReq) {
+
+	case GetHubStatus:
+		*(__le32 *)buf = cpu_to_le32(0);
+		break;
+	case GetPortStatus:
+		if (port >= ADMHCD_NUMPORTS)
+			goto err;
+		*(__le32 *)buf = cpu_to_le32(
+		    admhcd_reg_get(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4));
+		break;
+	case SetHubFeature:		/* We don't implement these */
+	case ClearHubFeature:
+		switch (wValue) {
+		case C_HUB_OVER_CURRENT:
+		case C_HUB_LOCAL_POWER:
+			break;
+		default:
+			goto err;
+		}
+	case SetPortFeature:
+		if (port >= ADMHCD_NUMPORTS)
+			goto err;
+
+		switch (wValue) {
+		case USB_PORT_FEAT_SUSPEND:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_PSS);
+			break;
+		case USB_PORT_FEAT_RESET:
+			if (admhcd_reg_get(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4)
+			    & ADMHCD_CCS) {
+				admhcd_reg_set(ahcd, 
+				    ADMHCD_REG_PORTSTATUS0 + port*4,
+				    ADMHCD_PRS | ADMHCD_CSC);
+				mdelay(50);
+				admhcd_reg_set(ahcd,
+				    ADMHCD_REG_PORTSTATUS0 + port*4,
+				    ADMHCD_PES | ADMHCD_CSC);
+			}
+			break;
+		case USB_PORT_FEAT_POWER:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_PPS);
+			break;
+		default:
+			goto err;
+		}
+		break;
+	case ClearPortFeature:
+		if (port >= ADMHCD_NUMPORTS)
+			goto err;
+
+		switch (wValue) {
+		case USB_PORT_FEAT_ENABLE:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_CCS);
+			break;
+		case USB_PORT_FEAT_C_ENABLE:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_PESC);
+			break;
+		case USB_PORT_FEAT_SUSPEND:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_POCI);
+			break;
+		case USB_PORT_FEAT_C_SUSPEND:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_PSSC);
+		case USB_PORT_FEAT_POWER:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_LSDA);
+			break;
+		case USB_PORT_FEAT_C_CONNECTION:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_CSC);
+			break;
+		case USB_PORT_FEAT_C_OVER_CURRENT:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_OCIC);
+			break;
+		case USB_PORT_FEAT_C_RESET:
+			admhcd_reg_set(ahcd, ADMHCD_REG_PORTSTATUS0 + port*4,
+			    ADMHCD_PRSC);
+			break;
+		default:
+			goto err;
+		}
+		break;
+	case GetHubDescriptor:
+		len = min_t(unsigned int, sizeof(root_hub_hub_des), wLength);
+		memcpy(buf, root_hub_hub_des, len);
+		break;
+	default:
+err:
+		retval = -EPIPE;
+	}
+
+	return retval;
+}
+
+static struct hc_driver adm5120_hc_driver = {
+	.description =		hcd_name,
+	.product_desc =		"ADM5120 HCD",
+	.hcd_priv_size =	sizeof(struct admhcd),
+	.flags =		HCD_USB11,
+	.urb_enqueue =		admhcd_urb_enqueue,
+	.urb_dequeue =		admhcd_urb_dequeue,
+	.endpoint_disable =	admhcd_endpoint_disable,
+	.get_frame_number =	admhcd_get_frame_number,
+	.hub_status_data =	admhcd_hub_status_data,
+	.hub_control =		admhcd_hub_control,
+};
+
+static int __init adm5120hcd_probe(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd;
+	struct admhcd *ahcd;
+	struct usb_device *udev;
+	int err = 0;
+
+	if (!request_mem_region(pdev->resource[0].start,
+	    pdev->resource[0].end - pdev->resource[0].start, hcd_name)) {
+		pr_debug("couldn't request mem\n");
+		err = -EBUSY;
+		goto out;
+	}
+
+	//hcd = usb_create_hcd(&adm5120_hc_driver, pdev, pdev->bus_id);
+	if (!hcd)
+		goto out_mem;
+
+	ahcd = hcd_to_admhcd(hcd);
+	dev_set_drvdata(pdev, ahcd);
+	hcd->self.controller = pdev;
+	//hcd->self.bus_name = pdev->bus_id;
+	hcd->irq = pdev->resource[1].start;
+	hcd->regs = (void *)pdev->resource[0].start;
+	hcd->product_desc = hcd_name;
+	ahcd->base = pdev->resource[0].start;
+
+	if (request_irq(pdev->resource[1].start, adm5120hcd_irq, 0, hcd_name,
+	    hcd)) {
+		pr_debug("couldn't request irq\n");
+		err = -EBUSY;
+		goto out_hcd;
+	}
+
+	//err = usb_register_bus(&hcd->self);
+	//if (err < 0)
+	//	goto out_irq;
+
+	spin_lock_init(&ahcd->lock);
+
+	admhcd_reg_set(ahcd, ADMHCD_REG_INTENABLE, 0);
+	mdelay(10);
+	admhcd_reg_set(ahcd, ADMHCD_REG_CONTROL, ADMHCD_SW_RESET);
+	while (admhcd_reg_get(ahcd, ADMHCD_REG_CONTROL) & ADMHCD_SW_RESET)
+		mdelay(1);
+
+	admhcd_reg_set(ahcd, ADMHCD_REG_CONTROL, ADMHCD_HOST_EN);
+	admhcd_reg_set(ahcd, ADMHCD_REG_HOSTHEAD, 0x00000000);
+	admhcd_reg_set(ahcd, ADMHCD_REG_FMINTERVAL, 0x20002edf);
+	admhcd_reg_set(ahcd, ADMHCD_REG_LSTHRESH, 0x628);
+	admhcd_reg_set(ahcd, ADMHCD_REG_INTENABLE,
+	    ADMHCD_INT_ACT | ADMHCD_INT_FATAL | ADMHCD_INT_SW | ADMHCD_INT_TD);
+	admhcd_reg_set(ahcd, ADMHCD_REG_INTSTATUS,
+	    ADMHCD_INT_ACT | ADMHCD_INT_FATAL | ADMHCD_INT_SW | ADMHCD_INT_TD);
+	admhcd_reg_set(ahcd, ADMHCD_REG_RHDESCR, ADMHCD_NPS | ADMHCD_LPSC);
+	admhcd_reg_set(ahcd, ADMHCD_REG_HOSTCONTROL, ADMHCD_STATE_OP);
+
+	udev = usb_alloc_dev(NULL, &hcd->self, 0);
+	if (!udev) {
+		err = -ENOMEM;
+		goto out_bus;
+	}
+
+	udev->speed = USB_SPEED_FULL;
+	hcd->state = HC_STATE_RUNNING;
+
+	//err = hcd_register_root(udev, hcd);
+	//if (err != 0) {
+	//	usb_put_dev(udev);
+	//	goto out_dev;
+	//}
+
+	return 0;
+
+out_dev:
+	usb_put_dev(udev);
+out_bus:
+	//usb_deregister_bus(&hcd->self);
+out_irq:
+	free_irq(pdev->resource[1].start, hcd);
+out_hcd:
+	usb_put_hcd(hcd);
+out_mem:
+	release_mem_region(pdev->resource[0].start,
+	    pdev->resource[0].end - pdev->resource[0].start);
+out:
+	return err;
+}
+
+static int __init_or_module adm5120hcd_remove(struct platform_device *pdev)
+{
+	device_init_wakeup(&pdev->dev, 0);
+}
+
+static struct platform_driver adm5120hcd_driver = {
+	.probe =	adm5120hcd_probe,
+	.remove =	adm5120hcd_remove,
+	.driver	=	{
+		.name 	= "adm5120-hcd",
+		.owner 	= THIS_MODULE,
+	},
+};
+
+static int __init adm5120hcd_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	return platform_driver_register(&adm5120hcd_driver);
+}
+
+static void __exit adm5120hcd_exit(void)
+{
+	platform_driver_unregister(&adm5120hcd_driver);
+}
+
+module_init(adm5120hcd_init);
+module_exit(adm5120hcd_exit);
diff --git a/target/linux/adm5120-2.6/image/Makefile b/target/linux/adm5120-2.6/image/Makefile
new file mode 100644
index 0000000000..2043ffa9e5
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/Makefile
@@ -0,0 +1,41 @@
+# 
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/image.mk
+
+define Build/Compile
+	rm -f $(KDIR)/loader.gz
+	$(MAKE) -C lzma-loader \
+		BUILD_DIR="$(KDIR)" \
+		TARGET="$(KDIR)" \
+		install
+	echo -ne "\\x00" >> $(KDIR)/loader.gz
+endef
+
+define Build/Clean
+	$(MAKE) -C lzma-loader clean
+endef
+
+define Image/Prepare
+	cat $(KDIR)/vmlinux | $(STAGING_DIR)/bin/lzma e -si -so -eos -lc1 -lp2 -pb2 > $(KDIR)/vmlinux.lzma
+endef
+
+define trxalign/jffs2-128k
+-a 0x20000
+endef
+define trxalign/jffs2-64k
+-a 0x10000
+endef
+define trxalign/squashfs
+-a 1024
+endef
+
+define Image/Build
+	$(STAGING_DIR)/bin/trx -o $(BIN_DIR)/openwrt-$(BOARD)-$(KERNEL)-$(1).trx -f $(KDIR)/loader.gz -f $(KDIR)/vmlinux.lzma $(call trxalign/$(1)) -f $(KDIR)/root.$(1)
+endef
+
+$(eval $(call BuildImage))
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/Makefile b/target/linux/adm5120-2.6/image/lzma-loader/Makefile
new file mode 100644
index 0000000000..e2afb186e0
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/Makefile
@@ -0,0 +1,34 @@
+# 
+# Copyright (C) 2006 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+# $Id: Makefile 4439 2006-08-04 17:14:36Z nbd $
+
+include $(TOPDIR)/rules.mk
+
+PKG_NAME := lzma-loader
+PKG_BUILD_DIR := $(BUILD_DIR)/$(PKG_NAME)
+
+$(PKG_BUILD_DIR)/.prepared:
+	mkdir $(PKG_BUILD_DIR)
+	$(CP) ./src/* $(PKG_BUILD_DIR)/
+	touch $@
+
+$(PKG_BUILD_DIR)/loader.gz: $(PKG_BUILD_DIR)/.prepared
+	$(MAKE) -C $(PKG_BUILD_DIR) CC="$(TARGET_CC)" \
+		LD="$(TARGET_CROSS)ld" CROSS_COMPILE="$(TARGET_CROSS)"
+
+download: 
+prepare: $(PKG_BUILD_DIR)/.prepared
+compile: $(PKG_BUILD_DIR)/loader.gz
+install:
+
+ifneq ($(TARGET),)
+install: compile
+	$(CP) $(PKG_BUILD_DIR)/loader.gz $(PKG_BUILD_DIR)/loader.elf $(TARGET)/
+endif
+
+clean:
+	rm -rf $(PKG_BUILD_DIR)
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/LzmaDecode.c b/target/linux/adm5120-2.6/image/lzma-loader/src/LzmaDecode.c
new file mode 100644
index 0000000000..951700bddf
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/LzmaDecode.c
@@ -0,0 +1,663 @@
+/*
+  LzmaDecode.c
+  LZMA Decoder
+  
+  LZMA SDK 4.05 Copyright (c) 1999-2004 Igor Pavlov (2004-08-25)
+  http://www.7-zip.org/
+
+  LZMA SDK is licensed under two licenses:
+  1) GNU Lesser General Public License (GNU LGPL)
+  2) Common Public License (CPL)
+  It means that you can select one of these two licenses and 
+  follow rules of that license.
+
+  SPECIAL EXCEPTION:
+  Igor Pavlov, as the author of this code, expressly permits you to 
+  statically or dynamically link your code (or bind by name) to the 
+  interfaces of this file without subjecting your linked code to the 
+  terms of the CPL or GNU LGPL. Any modifications or additions 
+  to this file, however, are subject to the LGPL or CPL terms.
+*/
+
+#include "LzmaDecode.h"
+
+#ifndef Byte
+#define Byte unsigned char
+#endif
+
+#define kNumTopBits 24
+#define kTopValue ((UInt32)1 << kNumTopBits)
+
+#define kNumBitModelTotalBits 11
+#define kBitModelTotal (1 << kNumBitModelTotalBits)
+#define kNumMoveBits 5
+
+typedef struct _CRangeDecoder
+{
+  Byte *Buffer;
+  Byte *BufferLim;
+  UInt32 Range;
+  UInt32 Code;
+  #ifdef _LZMA_IN_CB
+  ILzmaInCallback *InCallback;
+  int Result;
+  #endif
+  int ExtraBytes;
+} CRangeDecoder;
+
+Byte RangeDecoderReadByte(CRangeDecoder *rd)
+{
+  if (rd->Buffer == rd->BufferLim)
+  {
+    #ifdef _LZMA_IN_CB
+    UInt32 size;
+    rd->Result = rd->InCallback->Read(rd->InCallback, &rd->Buffer, &size);
+    rd->BufferLim = rd->Buffer + size;
+    if (size == 0)
+    #endif
+    {
+      rd->ExtraBytes = 1;
+      return 0xFF;
+    }
+  }
+  return (*rd->Buffer++);
+}
+
+/* #define ReadByte (*rd->Buffer++) */
+#define ReadByte (RangeDecoderReadByte(rd))
+
+void RangeDecoderInit(CRangeDecoder *rd,
+  #ifdef _LZMA_IN_CB
+    ILzmaInCallback *inCallback
+  #else
+    Byte *stream, UInt32 bufferSize
+  #endif
+    )
+{
+  int i;
+  #ifdef _LZMA_IN_CB
+  rd->InCallback = inCallback;
+  rd->Buffer = rd->BufferLim = 0;
+  #else
+  rd->Buffer = stream;
+  rd->BufferLim = stream + bufferSize;
+  #endif
+  rd->ExtraBytes = 0;
+  rd->Code = 0;
+  rd->Range = (0xFFFFFFFF);
+  for(i = 0; i < 5; i++)
+    rd->Code = (rd->Code << 8) | ReadByte;
+}
+
+#define RC_INIT_VAR UInt32 range = rd->Range; UInt32 code = rd->Code;        
+#define RC_FLUSH_VAR rd->Range = range; rd->Code = code;
+#define RC_NORMALIZE if (range < kTopValue) { range <<= 8; code = (code << 8) | ReadByte; }
+
+UInt32 RangeDecoderDecodeDirectBits(CRangeDecoder *rd, int numTotalBits)
+{
+  RC_INIT_VAR
+  UInt32 result = 0;
+  int i;
+  for (i = numTotalBits; i > 0; i--)
+  {
+    /* UInt32 t; */
+    range >>= 1;
+
+    result <<= 1;
+    if (code >= range)
+    {
+      code -= range;
+      result |= 1;
+    }
+    /*
+    t = (code - range) >> 31;
+    t &= 1;
+    code -= range & (t - 1);
+    result = (result + result) | (1 - t);
+    */
+    RC_NORMALIZE
+  }
+  RC_FLUSH_VAR
+  return result;
+}
+
+int RangeDecoderBitDecode(CProb *prob, CRangeDecoder *rd)
+{
+  UInt32 bound = (rd->Range >> kNumBitModelTotalBits) * *prob;
+  if (rd->Code < bound)
+  {
+    rd->Range = bound;
+    *prob += (kBitModelTotal - *prob) >> kNumMoveBits;
+    if (rd->Range < kTopValue)
+    {
+      rd->Code = (rd->Code << 8) | ReadByte;
+      rd->Range <<= 8;
+    }
+    return 0;
+  }
+  else
+  {
+    rd->Range -= bound;
+    rd->Code -= bound;
+    *prob -= (*prob) >> kNumMoveBits;
+    if (rd->Range < kTopValue)
+    {
+      rd->Code = (rd->Code << 8) | ReadByte;
+      rd->Range <<= 8;
+    }
+    return 1;
+  }
+}
+
+#define RC_GET_BIT2(prob, mi, A0, A1) \
+  UInt32 bound = (range >> kNumBitModelTotalBits) * *prob; \
+  if (code < bound) \
+    { A0; range = bound; *prob += (kBitModelTotal - *prob) >> kNumMoveBits; mi <<= 1; } \
+  else \
+    { A1; range -= bound; code -= bound; *prob -= (*prob) >> kNumMoveBits; mi = (mi + mi) + 1; } \
+  RC_NORMALIZE
+
+#define RC_GET_BIT(prob, mi) RC_GET_BIT2(prob, mi, ; , ;)               
+
+int RangeDecoderBitTreeDecode(CProb *probs, int numLevels, CRangeDecoder *rd)
+{
+  int mi = 1;
+  int i;
+  #ifdef _LZMA_LOC_OPT
+  RC_INIT_VAR
+  #endif
+  for(i = numLevels; i > 0; i--)
+  {
+    #ifdef _LZMA_LOC_OPT
+    CProb *prob = probs + mi;
+    RC_GET_BIT(prob, mi)
+    #else
+    mi = (mi + mi) + RangeDecoderBitDecode(probs + mi, rd);
+    #endif
+  }
+  #ifdef _LZMA_LOC_OPT
+  RC_FLUSH_VAR
+  #endif
+  return mi - (1 << numLevels);
+}
+
+int RangeDecoderReverseBitTreeDecode(CProb *probs, int numLevels, CRangeDecoder *rd)
+{
+  int mi = 1;
+  int i;
+  int symbol = 0;
+  #ifdef _LZMA_LOC_OPT
+  RC_INIT_VAR
+  #endif
+  for(i = 0; i < numLevels; i++)
+  {
+    #ifdef _LZMA_LOC_OPT
+    CProb *prob = probs + mi;
+    RC_GET_BIT2(prob, mi, ; , symbol |= (1 << i))
+    #else
+    int bit = RangeDecoderBitDecode(probs + mi, rd);
+    mi = mi + mi + bit;
+    symbol |= (bit << i);
+    #endif
+  }
+  #ifdef _LZMA_LOC_OPT
+  RC_FLUSH_VAR
+  #endif
+  return symbol;
+}
+
+Byte LzmaLiteralDecode(CProb *probs, CRangeDecoder *rd)
+{ 
+  int symbol = 1;
+  #ifdef _LZMA_LOC_OPT
+  RC_INIT_VAR
+  #endif
+  do
+  {
+    #ifdef _LZMA_LOC_OPT
+    CProb *prob = probs + symbol;
+    RC_GET_BIT(prob, symbol)
+    #else
+    symbol = (symbol + symbol) | RangeDecoderBitDecode(probs + symbol, rd);
+    #endif
+  }
+  while (symbol < 0x100);
+  #ifdef _LZMA_LOC_OPT
+  RC_FLUSH_VAR
+  #endif
+  return symbol;
+}
+
+Byte LzmaLiteralDecodeMatch(CProb *probs, CRangeDecoder *rd, Byte matchByte)
+{ 
+  int symbol = 1;
+  #ifdef _LZMA_LOC_OPT
+  RC_INIT_VAR
+  #endif
+  do
+  {
+    int bit;
+    int matchBit = (matchByte >> 7) & 1;
+    matchByte <<= 1;
+    #ifdef _LZMA_LOC_OPT
+    {
+      CProb *prob = probs + ((1 + matchBit) << 8) + symbol;
+      RC_GET_BIT2(prob, symbol, bit = 0, bit = 1)
+    }
+    #else
+    bit = RangeDecoderBitDecode(probs + ((1 + matchBit) << 8) + symbol, rd);
+    symbol = (symbol << 1) | bit;
+    #endif
+    if (matchBit != bit)
+    {
+      while (symbol < 0x100)
+      {
+        #ifdef _LZMA_LOC_OPT
+        CProb *prob = probs + symbol;
+        RC_GET_BIT(prob, symbol)
+        #else
+        symbol = (symbol + symbol) | RangeDecoderBitDecode(probs + symbol, rd);
+        #endif
+      }
+      break;
+    }
+  }
+  while (symbol < 0x100);
+  #ifdef _LZMA_LOC_OPT
+  RC_FLUSH_VAR
+  #endif
+  return symbol;
+}
+
+#define kNumPosBitsMax 4
+#define kNumPosStatesMax (1 << kNumPosBitsMax)
+
+#define kLenNumLowBits 3
+#define kLenNumLowSymbols (1 << kLenNumLowBits)
+#define kLenNumMidBits 3
+#define kLenNumMidSymbols (1 << kLenNumMidBits)
+#define kLenNumHighBits 8
+#define kLenNumHighSymbols (1 << kLenNumHighBits)
+
+#define LenChoice 0
+#define LenChoice2 (LenChoice + 1)
+#define LenLow (LenChoice2 + 1)
+#define LenMid (LenLow + (kNumPosStatesMax << kLenNumLowBits))
+#define LenHigh (LenMid + (kNumPosStatesMax << kLenNumMidBits))
+#define kNumLenProbs (LenHigh + kLenNumHighSymbols) 
+
+int LzmaLenDecode(CProb *p, CRangeDecoder *rd, int posState)
+{
+  if(RangeDecoderBitDecode(p + LenChoice, rd) == 0)
+    return RangeDecoderBitTreeDecode(p + LenLow +
+        (posState << kLenNumLowBits), kLenNumLowBits, rd);
+  if(RangeDecoderBitDecode(p + LenChoice2, rd) == 0)
+    return kLenNumLowSymbols + RangeDecoderBitTreeDecode(p + LenMid +
+        (posState << kLenNumMidBits), kLenNumMidBits, rd);
+  return kLenNumLowSymbols + kLenNumMidSymbols + 
+      RangeDecoderBitTreeDecode(p + LenHigh, kLenNumHighBits, rd);
+}
+
+#define kNumStates 12
+
+#define kStartPosModelIndex 4
+#define kEndPosModelIndex 14
+#define kNumFullDistances (1 << (kEndPosModelIndex >> 1))
+
+#define kNumPosSlotBits 6
+#define kNumLenToPosStates 4
+
+#define kNumAlignBits 4
+#define kAlignTableSize (1 << kNumAlignBits)
+
+#define kMatchMinLen 2
+
+#define IsMatch 0
+#define IsRep (IsMatch + (kNumStates << kNumPosBitsMax))
+#define IsRepG0 (IsRep + kNumStates)
+#define IsRepG1 (IsRepG0 + kNumStates)
+#define IsRepG2 (IsRepG1 + kNumStates)
+#define IsRep0Long (IsRepG2 + kNumStates)
+#define PosSlot (IsRep0Long + (kNumStates << kNumPosBitsMax))
+#define SpecPos (PosSlot + (kNumLenToPosStates << kNumPosSlotBits))
+#define Align (SpecPos + kNumFullDistances - kEndPosModelIndex)
+#define LenCoder (Align + kAlignTableSize)
+#define RepLenCoder (LenCoder + kNumLenProbs)
+#define Literal (RepLenCoder + kNumLenProbs)
+
+#if Literal != LZMA_BASE_SIZE
+StopCompilingDueBUG
+#endif
+
+#ifdef _LZMA_OUT_READ
+
+typedef struct _LzmaVarState
+{
+  CRangeDecoder RangeDecoder;
+  Byte *Dictionary;
+  UInt32 DictionarySize;
+  UInt32 DictionaryPos;
+  UInt32 GlobalPos;
+  UInt32 Reps[4];
+  int lc;
+  int lp;
+  int pb;
+  int State;
+  int PreviousIsMatch;
+  int RemainLen;
+} LzmaVarState;
+
+int LzmaDecoderInit(
+    unsigned char *buffer, UInt32 bufferSize,
+    int lc, int lp, int pb,
+    unsigned char *dictionary, UInt32 dictionarySize,
+    #ifdef _LZMA_IN_CB
+    ILzmaInCallback *inCallback
+    #else
+    unsigned char *inStream, UInt32 inSize
+    #endif
+    )
+{
+  LzmaVarState *vs = (LzmaVarState *)buffer;
+  CProb *p = (CProb *)(buffer + sizeof(LzmaVarState));
+  UInt32 numProbs = Literal + ((UInt32)LZMA_LIT_SIZE << (lc + lp));
+  UInt32 i;
+  if (bufferSize < numProbs * sizeof(CProb) + sizeof(LzmaVarState))
+    return LZMA_RESULT_NOT_ENOUGH_MEM;
+  vs->Dictionary = dictionary;
+  vs->DictionarySize = dictionarySize;
+  vs->DictionaryPos = 0;
+  vs->GlobalPos = 0;
+  vs->Reps[0] = vs->Reps[1] = vs->Reps[2] = vs->Reps[3] = 1;
+  vs->lc = lc;
+  vs->lp = lp;
+  vs->pb = pb;
+  vs->State = 0;
+  vs->PreviousIsMatch = 0;
+  vs->RemainLen = 0;
+  dictionary[dictionarySize - 1] = 0;
+  for (i = 0; i < numProbs; i++)
+    p[i] = kBitModelTotal >> 1; 
+  RangeDecoderInit(&vs->RangeDecoder, 
+      #ifdef _LZMA_IN_CB
+      inCallback
+      #else
+      inStream, inSize
+      #endif
+  );
+  return LZMA_RESULT_OK;
+}
+
+int LzmaDecode(unsigned char *buffer, 
+    unsigned char *outStream, UInt32 outSize,
+    UInt32 *outSizeProcessed)
+{
+  LzmaVarState *vs = (LzmaVarState *)buffer;
+  CProb *p = (CProb *)(buffer + sizeof(LzmaVarState));
+  CRangeDecoder rd = vs->RangeDecoder;
+  int state = vs->State;
+  int previousIsMatch = vs->PreviousIsMatch;
+  Byte previousByte;
+  UInt32 rep0 = vs->Reps[0], rep1 = vs->Reps[1], rep2 = vs->Reps[2], rep3 = vs->Reps[3];
+  UInt32 nowPos = 0;
+  UInt32 posStateMask = (1 << (vs->pb)) - 1;
+  UInt32 literalPosMask = (1 << (vs->lp)) - 1;
+  int lc = vs->lc;
+  int len = vs->RemainLen;
+  UInt32 globalPos = vs->GlobalPos;
+
+  Byte *dictionary = vs->Dictionary;
+  UInt32 dictionarySize = vs->DictionarySize;
+  UInt32 dictionaryPos = vs->DictionaryPos;
+
+  if (len == -1)
+  {
+    *outSizeProcessed = 0;
+    return LZMA_RESULT_OK;
+  }
+
+  while(len > 0 && nowPos < outSize)
+  {
+    UInt32 pos = dictionaryPos - rep0;
+    if (pos >= dictionarySize)
+      pos += dictionarySize;
+    outStream[nowPos++] = dictionary[dictionaryPos] = dictionary[pos];
+    if (++dictionaryPos == dictionarySize)
+      dictionaryPos = 0;
+    len--;
+  }
+  if (dictionaryPos == 0)
+    previousByte = dictionary[dictionarySize - 1];
+  else
+    previousByte = dictionary[dictionaryPos - 1];
+#else
+
+int LzmaDecode(
+    Byte *buffer, UInt32 bufferSize,
+    int lc, int lp, int pb,
+    #ifdef _LZMA_IN_CB
+    ILzmaInCallback *inCallback,
+    #else
+    unsigned char *inStream, UInt32 inSize,
+    #endif
+    unsigned char *outStream, UInt32 outSize,
+    UInt32 *outSizeProcessed)
+{
+  UInt32 numProbs = Literal + ((UInt32)LZMA_LIT_SIZE << (lc + lp));
+  CProb *p = (CProb *)buffer;
+  CRangeDecoder rd;
+  UInt32 i;
+  int state = 0;
+  int previousIsMatch = 0;
+  Byte previousByte = 0;
+  UInt32 rep0 = 1, rep1 = 1, rep2 = 1, rep3 = 1;
+  UInt32 nowPos = 0;
+  UInt32 posStateMask = (1 << pb) - 1;
+  UInt32 literalPosMask = (1 << lp) - 1;
+  int len = 0;
+  if (bufferSize < numProbs * sizeof(CProb))
+    return LZMA_RESULT_NOT_ENOUGH_MEM;
+  for (i = 0; i < numProbs; i++)
+    p[i] = kBitModelTotal >> 1; 
+  RangeDecoderInit(&rd, 
+      #ifdef _LZMA_IN_CB
+      inCallback
+      #else
+      inStream, inSize
+      #endif
+      );
+#endif
+
+  *outSizeProcessed = 0;
+  while(nowPos < outSize)
+  {
+    int posState = (int)(
+        (nowPos 
+        #ifdef _LZMA_OUT_READ
+        + globalPos
+        #endif
+        )
+        & posStateMask);
+    #ifdef _LZMA_IN_CB
+    if (rd.Result != LZMA_RESULT_OK)
+      return rd.Result;
+    #endif
+    if (rd.ExtraBytes != 0)
+      return LZMA_RESULT_DATA_ERROR;
+    if (RangeDecoderBitDecode(p + IsMatch + (state << kNumPosBitsMax) + posState, &rd) == 0)
+    {
+      CProb *probs = p + Literal + (LZMA_LIT_SIZE * 
+        (((
+        (nowPos 
+        #ifdef _LZMA_OUT_READ
+        + globalPos
+        #endif
+        )
+        & literalPosMask) << lc) + (previousByte >> (8 - lc))));
+
+      if (state < 4) state = 0;
+      else if (state < 10) state -= 3;
+      else state -= 6;
+      if (previousIsMatch)
+      {
+        Byte matchByte;
+        #ifdef _LZMA_OUT_READ
+        UInt32 pos = dictionaryPos - rep0;
+        if (pos >= dictionarySize)
+          pos += dictionarySize;
+        matchByte = dictionary[pos];
+        #else
+        matchByte = outStream[nowPos - rep0];
+        #endif
+        previousByte = LzmaLiteralDecodeMatch(probs, &rd, matchByte);
+        previousIsMatch = 0;
+      }
+      else
+        previousByte = LzmaLiteralDecode(probs, &rd);
+      outStream[nowPos++] = previousByte;
+      #ifdef _LZMA_OUT_READ
+      dictionary[dictionaryPos] = previousByte;
+      if (++dictionaryPos == dictionarySize)
+        dictionaryPos = 0;
+      #endif
+    }
+    else             
+    {
+      previousIsMatch = 1;
+      if (RangeDecoderBitDecode(p + IsRep + state, &rd) == 1)
+      {
+        if (RangeDecoderBitDecode(p + IsRepG0 + state, &rd) == 0)
+        {
+          if (RangeDecoderBitDecode(p + IsRep0Long + (state << kNumPosBitsMax) + posState, &rd) == 0)
+          {
+            #ifdef _LZMA_OUT_READ
+            UInt32 pos;
+            #endif
+            if (
+               (nowPos 
+                #ifdef _LZMA_OUT_READ
+                + globalPos
+                #endif
+               )
+               == 0)
+              return LZMA_RESULT_DATA_ERROR;
+            state = state < 7 ? 9 : 11;
+            #ifdef _LZMA_OUT_READ
+            pos = dictionaryPos - rep0;
+            if (pos >= dictionarySize)
+              pos += dictionarySize;
+            previousByte = dictionary[pos];
+            dictionary[dictionaryPos] = previousByte;
+            if (++dictionaryPos == dictionarySize)
+              dictionaryPos = 0;
+            #else
+            previousByte = outStream[nowPos - rep0];
+            #endif
+            outStream[nowPos++] = previousByte;
+            continue;
+          }
+        }
+        else
+        {
+          UInt32 distance;
+          if(RangeDecoderBitDecode(p + IsRepG1 + state, &rd) == 0)
+            distance = rep1;
+          else 
+          {
+            if(RangeDecoderBitDecode(p + IsRepG2 + state, &rd) == 0)
+              distance = rep2;
+            else
+            {
+              distance = rep3;
+              rep3 = rep2;
+            }
+            rep2 = rep1;
+          }
+          rep1 = rep0;
+          rep0 = distance;
+        }
+        len = LzmaLenDecode(p + RepLenCoder, &rd, posState);
+        state = state < 7 ? 8 : 11;
+      }
+      else
+      {
+        int posSlot;
+        rep3 = rep2;
+        rep2 = rep1;
+        rep1 = rep0;
+        state = state < 7 ? 7 : 10;
+        len = LzmaLenDecode(p + LenCoder, &rd, posState);
+        posSlot = RangeDecoderBitTreeDecode(p + PosSlot +
+            ((len < kNumLenToPosStates ? len : kNumLenToPosStates - 1) << 
+            kNumPosSlotBits), kNumPosSlotBits, &rd);
+        if (posSlot >= kStartPosModelIndex)
+        {
+          int numDirectBits = ((posSlot >> 1) - 1);
+          rep0 = ((2 | ((UInt32)posSlot & 1)) << numDirectBits);
+          if (posSlot < kEndPosModelIndex)
+          {
+            rep0 += RangeDecoderReverseBitTreeDecode(
+                p + SpecPos + rep0 - posSlot - 1, numDirectBits, &rd);
+          }
+          else
+          {
+            rep0 += RangeDecoderDecodeDirectBits(&rd, 
+                numDirectBits - kNumAlignBits) << kNumAlignBits;
+            rep0 += RangeDecoderReverseBitTreeDecode(p + Align, kNumAlignBits, &rd);
+          }
+        }
+        else
+          rep0 = posSlot;
+        rep0++;
+      }
+      if (rep0 == (UInt32)(0))
+      {
+        /* it's for stream version */
+        len = -1;
+        break;
+      }
+      if (rep0 > nowPos 
+        #ifdef _LZMA_OUT_READ
+        + globalPos
+        #endif
+        )
+      {
+        return LZMA_RESULT_DATA_ERROR;
+      }
+      len += kMatchMinLen;
+      do
+      {
+        #ifdef _LZMA_OUT_READ
+        UInt32 pos = dictionaryPos - rep0;
+        if (pos >= dictionarySize)
+          pos += dictionarySize;
+        previousByte = dictionary[pos];
+        dictionary[dictionaryPos] = previousByte;
+        if (++dictionaryPos == dictionarySize)
+          dictionaryPos = 0;
+        #else
+        previousByte = outStream[nowPos - rep0];
+        #endif
+        outStream[nowPos++] = previousByte;
+        len--;
+      }
+      while(len > 0 && nowPos < outSize);
+    }
+  }
+
+  #ifdef _LZMA_OUT_READ
+  vs->RangeDecoder = rd;
+  vs->DictionaryPos = dictionaryPos;
+  vs->GlobalPos = globalPos + nowPos;
+  vs->Reps[0] = rep0;
+  vs->Reps[1] = rep1;
+  vs->Reps[2] = rep2;
+  vs->Reps[3] = rep3;
+  vs->State = state;
+  vs->PreviousIsMatch = previousIsMatch;
+  vs->RemainLen = len;
+  #endif
+
+  *outSizeProcessed = nowPos;
+  return LZMA_RESULT_OK;
+}
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/LzmaDecode.h b/target/linux/adm5120-2.6/image/lzma-loader/src/LzmaDecode.h
new file mode 100644
index 0000000000..f58944e3c3
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/LzmaDecode.h
@@ -0,0 +1,100 @@
+/* 
+  LzmaDecode.h
+  LZMA Decoder interface
+
+  LZMA SDK 4.05 Copyright (c) 1999-2004 Igor Pavlov (2004-08-25)
+  http://www.7-zip.org/
+
+  LZMA SDK is licensed under two licenses:
+  1) GNU Lesser General Public License (GNU LGPL)
+  2) Common Public License (CPL)
+  It means that you can select one of these two licenses and 
+  follow rules of that license.
+
+  SPECIAL EXCEPTION:
+  Igor Pavlov, as the author of this code, expressly permits you to 
+  statically or dynamically link your code (or bind by name) to the 
+  interfaces of this file without subjecting your linked code to the 
+  terms of the CPL or GNU LGPL. Any modifications or additions 
+  to this file, however, are subject to the LGPL or CPL terms.
+*/
+
+#ifndef __LZMADECODE_H
+#define __LZMADECODE_H
+
+/* #define _LZMA_IN_CB */
+/* Use callback for input data */
+
+/* #define _LZMA_OUT_READ */
+/* Use read function for output data */
+
+/* #define _LZMA_PROB32 */
+/* It can increase speed on some 32-bit CPUs, 
+   but memory usage will be doubled in that case */
+
+/* #define _LZMA_LOC_OPT */
+/* Enable local speed optimizations inside code */
+
+#ifndef UInt32
+#ifdef _LZMA_UINT32_IS_ULONG
+#define UInt32 unsigned long
+#else
+#define UInt32 unsigned int
+#endif
+#endif
+
+#ifdef _LZMA_PROB32
+#define CProb UInt32
+#else
+#define CProb unsigned short
+#endif
+
+#define LZMA_RESULT_OK 0
+#define LZMA_RESULT_DATA_ERROR 1
+#define LZMA_RESULT_NOT_ENOUGH_MEM 2
+
+#ifdef _LZMA_IN_CB
+typedef struct _ILzmaInCallback
+{
+  int (*Read)(void *object, unsigned char **buffer, UInt32 *bufferSize);
+} ILzmaInCallback;
+#endif
+
+#define LZMA_BASE_SIZE 1846
+#define LZMA_LIT_SIZE 768
+
+/* 
+bufferSize = (LZMA_BASE_SIZE + (LZMA_LIT_SIZE << (lc + lp)))* sizeof(CProb)
+bufferSize += 100 in case of _LZMA_OUT_READ
+by default CProb is unsigned short, 
+but if specify _LZMA_PROB_32, CProb will be UInt32(unsigned int)
+*/
+
+#ifdef _LZMA_OUT_READ
+int LzmaDecoderInit(
+    unsigned char *buffer, UInt32 bufferSize,
+    int lc, int lp, int pb,
+    unsigned char *dictionary, UInt32 dictionarySize,
+  #ifdef _LZMA_IN_CB
+    ILzmaInCallback *inCallback
+  #else
+    unsigned char *inStream, UInt32 inSize
+  #endif
+);
+#endif
+
+int LzmaDecode(
+    unsigned char *buffer, 
+  #ifndef _LZMA_OUT_READ
+    UInt32 bufferSize,
+    int lc, int lp, int pb,
+  #ifdef _LZMA_IN_CB
+    ILzmaInCallback *inCallback,
+  #else
+    unsigned char *inStream, UInt32 inSize,
+  #endif
+  #endif
+    unsigned char *outStream, UInt32 outSize,
+    UInt32 *outSizeProcessed);
+
+#endif
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/Makefile b/target/linux/adm5120-2.6/image/lzma-loader/src/Makefile
new file mode 100644
index 0000000000..85a864674b
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/Makefile
@@ -0,0 +1,77 @@
+#
+# Makefile for Broadcom BCM947XX boards
+#
+# Copyright 2001-2003, Broadcom Corporation
+# All Rights Reserved.
+# 
+# THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+# KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+# SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+# FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+#
+# Copyright 2004  Manuel Novoa III <mjn3@codepoet.org>
+#   Modified to support bzip'd kernels.
+#   Of course, it would be better to integrate bunzip capability into CFE.
+#
+# Copyright 2005  Oleg I. Vdovikin <oleg@cs.msu.su>
+#   Cleaned up, modified for lzma support, removed from kernel
+#
+
+TEXT_START	:= 0x80001000
+BZ_TEXT_START	:= 0x80300000
+
+OBJCOPY		:= $(CROSS_COMPILE)objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S
+
+CFLAGS		= -D__KERNEL__ -Wall -Wstrict-prototypes -Wno-trigraphs -Os \
+		  -fno-strict-aliasing -fno-common -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic \
+		  -ffunction-sections -pipe -mlong-calls -fno-common \
+		  -mabi=32 -march=mips32 -Wa,-32 -Wa,-march=mips32 -Wa,-mips32 -Wa,--trap
+CFLAGS		+= -DLOADADDR=$(TEXT_START) -D_LZMA_IN_CB
+
+ASFLAGS		= $(CFLAGS) -D__ASSEMBLY__ -DBZ_TEXT_START=$(BZ_TEXT_START)
+
+SEDFLAGS	:= s/BZ_TEXT_START/$(BZ_TEXT_START)/;s/TEXT_START/$(TEXT_START)/
+
+OBJECTS		:= head.o data.o
+
+all: loader.gz loader.elf
+
+# Don't build dependencies, this may die if $(CC) isn't gcc
+dep:
+
+install:
+
+loader.gz: loader
+	gzip -nc9 $< > $@
+
+loader.elf: loader.o
+	cp $< $@
+
+loader: loader.o
+	$(OBJCOPY) $< $@
+
+loader.o: loader.lds $(OBJECTS)
+	$(LD) -static --gc-sections -no-warn-mismatch -T loader.lds -o $@ $(OBJECTS)
+
+loader.lds: loader.lds.in Makefile
+	@sed "$(SEDFLAGS)" < $< > $@
+
+data.o: data.lds decompress.image
+	$(LD) -no-warn-mismatch -T data.lds -r -o $@ -b binary decompress.image -b elf32-tradlittlemips
+
+data.lds:
+	@echo "SECTIONS { .data : { code_start = .; *(.data) code_stop = .; }}" > $@
+
+decompress.image: decompress
+	$(OBJCOPY) $< $@
+
+decompress: decompress.lds decompress.o LzmaDecode.o
+	$(LD) -static --gc-sections -no-warn-mismatch -T decompress.lds -o $@ decompress.o LzmaDecode.o
+
+decompress.lds: decompress.lds.in Makefile
+	@sed "$(SEDFLAGS)" < $< > $@
+
+mrproper: clean
+
+clean:
+	rm -f loader.gz loader decompress *.lds *.o *.image
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/README b/target/linux/adm5120-2.6/image/lzma-loader/src/README
new file mode 100644
index 0000000000..16649e9500
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/README
@@ -0,0 +1,55 @@
+/*
+ * LZMA compressed kernel decompressor for bcm947xx boards
+ *
+ * Copyright (C) 2005 by Oleg I. Vdovikin <oleg@cs.msu.su>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+The code is intended to decompress kernel, being compressed using lzma utility
+build using 7zip LZMA SDK. This utility is located in the LZMA_Alone directory
+
+decompressor code expects that your .trx file consist of three partitions: 
+
+1) decompressor itself (this is gziped code which pmon/cfe will extract and run
+on boot-up instead of real kernel)
+2) LZMA compressed kernel (both streamed and regular modes are supported now)
+3) Root filesystem
+
+Please be sure to apply the following patch for use this new trx layout (it will
+allow using both new and old trx files for root filesystem lookup code)
+
+--- linuz/arch/mips/brcm-boards/bcm947xx/setup.c        2005-01-23 19:24:27.503322896 +0300
++++ linux/arch/mips/brcm-boards/bcm947xx/setup.c        2005-01-23 19:29:05.237100944 +0300
+@@ -221,7 +221,9 @@
+                /* Try looking at TRX header for rootfs offset */
+                if (le32_to_cpu(trx->magic) == TRX_MAGIC) {
+                        bcm947xx_parts[1].offset = off;
+-                       if (le32_to_cpu(trx->offsets[1]) > off)
++                       if (le32_to_cpu(trx->offsets[2]) > off)
++                               off = le32_to_cpu(trx->offsets[2]);
++                       else if (le32_to_cpu(trx->offsets[1]) > off)
+                                off = le32_to_cpu(trx->offsets[1]);
+                        continue;
+                }
+
+
+Revision history:
+	0.02	Initial release
+	0.03	Added Mineharu Takahara <mtakahar@yahoo.com> patch to pass actual
+		output size to decoder (stream mode compressed input is not 
+		a requirement anymore)
+	0.04	Reordered functions using lds script
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/decompress.c b/target/linux/adm5120-2.6/image/lzma-loader/src/decompress.c
new file mode 100644
index 0000000000..b0ed2fc8c4
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/decompress.c
@@ -0,0 +1,231 @@
+/*
+ * LZMA compressed kernel decompressor for bcm947xx boards
+ *
+ * Copyright (C) 2005 by Oleg I. Vdovikin <oleg@cs.msu.su>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ *
+ * Please note, this was code based on the bunzip2 decompressor code
+ * by Manuel Novoa III  (mjn3@codepoet.org), although the only thing left
+ * is an idea and part of original vendor code
+ *
+ *
+ * 12-Mar-2005  Mineharu Takahara <mtakahar@yahoo.com>
+ *   pass actual output size to decoder (stream mode
+ *   compressed input is not a requirement anymore)
+ *
+ * 24-Apr-2005 Oleg I. Vdovikin
+ *   reordered functions using lds script, removed forward decl
+ *
+ */
+
+#include "LzmaDecode.h"
+
+#define BCM4710_FLASH		0x1fc00000	/* Flash */
+
+#define KSEG0			0x80000000
+#define KSEG1			0xa0000000
+
+#define KSEG1ADDR(a)		((((unsigned)(a)) & 0x1fffffffU) | KSEG1)
+
+#define Index_Invalidate_I	0x00
+#define Index_Writeback_Inv_D   0x01
+
+#define cache_unroll(base,op)	\
+	__asm__ __volatile__(		\
+		".set noreorder;\n"		\
+		".set mips3;\n"			\
+		"cache %1, (%0);\n"		\
+		".set mips0;\n"			\
+		".set reorder\n"		\
+		:						\
+		: "r" (base),			\
+		  "i" (op));
+
+static __inline__ void blast_icache(unsigned long size, unsigned long lsize)
+{
+	unsigned long start = KSEG0;
+	unsigned long end = (start + size);
+
+	while(start < end) {
+		cache_unroll(start,Index_Invalidate_I);
+		start += lsize;
+	}
+}
+
+static __inline__ void blast_dcache(unsigned long size, unsigned long lsize)
+{
+	unsigned long start = KSEG0;
+	unsigned long end = (start + size);
+
+	while(start < end) {
+		cache_unroll(start,Index_Writeback_Inv_D);
+		start += lsize;
+	}
+}
+
+#define TRX_MAGIC       0x30524448      /* "HDR0" */
+
+struct trx_header {
+	unsigned int magic;		/* "HDR0" */
+	unsigned int len;		/* Length of file including header */
+	unsigned int crc32;		/* 32-bit CRC from flag_version to end of file */
+	unsigned int flag_version;	/* 0:15 flags, 16:31 version */
+	unsigned int offsets[3];	/* Offsets of partitions from start of header */
+};
+
+/* beyound the image end, size not known in advance */
+extern unsigned char workspace[];
+
+unsigned int offset;
+unsigned char *data;
+
+/* flash access should be aligned, so wrapper is used */
+/* read byte from the flash, all accesses are 32-bit aligned */
+static int read_byte(void *object, unsigned char **buffer, UInt32 *bufferSize)
+{
+	static unsigned int val;
+
+	if (((unsigned int)offset % 4) == 0) {
+		val = *(unsigned int *)data;
+		data += 4;
+	}
+	
+	*bufferSize = 1;
+	*buffer = ((unsigned char *)&val) + (offset++ & 3);
+	
+	return LZMA_RESULT_OK;
+}
+
+static __inline__ unsigned char get_byte(void)
+{
+	unsigned char *buffer;
+	UInt32 fake;
+	
+	return read_byte(0, &buffer, &fake), *buffer;
+}
+
+/* should be the first function */
+void entry(unsigned long icache_size, unsigned long icache_lsize, 
+	unsigned long dcache_size, unsigned long dcache_lsize)
+{
+	unsigned int i;  /* temp value */
+	unsigned int lc; /* literal context bits */
+	unsigned int lp; /* literal pos state bits */
+	unsigned int pb; /* pos state bits */
+	unsigned int osize; /* uncompressed size */
+
+	ILzmaInCallback callback;
+	callback.Read = read_byte;
+
+    uart_write_str("decompress kernel ... ");
+    
+	/* look for trx header, 32-bit data access */
+	for (data = ((unsigned char *) KSEG1ADDR(BCM4710_FLASH));
+		((struct trx_header *)data)->magic != TRX_MAGIC; data += 65536);
+
+	/* compressed kernel is in the partition 0 or 1 */
+	if (((struct trx_header *)data)->offsets[1] > 65536) 
+		data += ((struct trx_header *)data)->offsets[0];
+	else
+		data += ((struct trx_header *)data)->offsets[1];
+
+	offset = 0;
+
+	/* lzma args */
+	i = get_byte();
+	lc = i % 9, i = i / 9;
+	lp = i % 5, pb = i / 5;
+
+	/* skip rest of the LZMA coder property */
+	for (i = 0; i < 4; i++)
+		get_byte();
+
+	/* read the lower half of uncompressed size in the header */
+	osize = ((unsigned int)get_byte()) +
+		((unsigned int)get_byte() << 8) +
+		((unsigned int)get_byte() << 16) +
+		((unsigned int)get_byte() << 24);
+
+	/* skip rest of the header (upper half of uncompressed size) */
+	for (i = 0; i < 4; i++) 
+		get_byte();
+
+	/* decompress kernel */
+	if (LzmaDecode(workspace, ~0, lc, lp, pb, &callback,
+		(unsigned char*)LOADADDR, osize, &i) == LZMA_RESULT_OK)
+	{
+		blast_dcache(dcache_size, dcache_lsize);
+		blast_icache(icache_size, icache_lsize);
+
+		/* Jump to load address */
+        uart_write_str("ok\r\n");
+		((void (*)(void)) LOADADDR)();
+	}
+    uart_write_str("failed\r\n");
+    while (1 );
+}
+
+/*  *********************************************************************
+    *  
+    *  ADM5120 UART driver			File: dev_adm_uart.c
+    *  
+    *  This is a console device driver for an ADM5120 UART
+    *  
+    *********************************************************************
+    *
+    *  Copyright 2006
+    *  Compex Systems. All rights reserved.
+    *
+    ********************************************************************* */
+
+#define READCSR(r)      *(volatile UInt32 *)(0xB2600000+(r))
+#define WRITECSR(r,v)   *(volatile UInt32 *)(0xB2600000+(r)) = v
+
+#define UART_DR_REG         0x00
+#define UART_FR_REG         0x18
+#define UART_TX_FIFO_FULL   0x20
+
+int uart_write(int val)
+{
+	WRITECSR(UART_DR_REG, val);
+    while ( (READCSR(UART_FR_REG) & UART_TX_FIFO_FULL) );
+    return 0;
+}
+
+int uart_write_str(char * str)
+{
+    while ( *str != 0 ) {
+        uart_write ( *str++ );
+    }
+    return 0;
+}
+
+int uart_write_hex(int val)
+{
+    int i;
+    int tmp;
+    
+    uart_write_str("0x");
+    for ( i=0 ; i<8 ; i++ ) {
+        tmp = (val >> ((7-i) * 4 )) & 0xf;
+        tmp = tmp < 10 ? (tmp + '0') : (tmp + 'A' - 10);
+        uart_write(tmp);
+    }
+    uart_write_str("\r\n");
+    return 0;
+}
+
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/decompress.lds.in b/target/linux/adm5120-2.6/image/lzma-loader/src/decompress.lds.in
new file mode 100644
index 0000000000..33f56f8a09
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/decompress.lds.in
@@ -0,0 +1,20 @@
+OUTPUT_ARCH(mips)
+ENTRY(entry)
+SECTIONS {
+	. = BZ_TEXT_START;
+	.text : {
+		*(.text.entry)
+		*(.text)
+		*(.rodata)
+	}
+
+	.data : {
+		*(.data)
+	}
+
+	.bss : {
+		*(.bss)
+	}
+
+	workspace = .;
+}
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/head.S b/target/linux/adm5120-2.6/image/lzma-loader/src/head.S
new file mode 100644
index 0000000000..9bfbd53d51
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/head.S
@@ -0,0 +1,155 @@
+/* Copyright 2005 Oleg I. Vdovikin (oleg@cs.msu.su)	*/
+/* cache manipulation adapted from Broadcom code 	*/
+/* idea taken from original bunzip2 decompressor code	*/
+/* Copyright 2004 Manuel Novoa III (mjn3@codepoet.org)	*/
+/* Licensed under the linux kernel's version of the GPL.*/
+
+#include <asm/asm.h>
+#include <asm/regdef.h>
+
+#define KSEG0		0x80000000
+
+#define C0_CONFIG	$16
+#define C0_TAGLO	$28
+#define C0_TAGHI	$29
+
+#define	CONF1_DA_SHIFT	7			/* D$ associativity */
+#define CONF1_DA_MASK	0x00000380
+#define CONF1_DA_BASE	1
+#define CONF1_DL_SHIFT	10			/* D$ line size */
+#define CONF1_DL_MASK	0x00001c00
+#define CONF1_DL_BASE	2
+#define CONF1_DS_SHIFT	13			/* D$ sets/way */
+#define CONF1_DS_MASK	0x0000e000
+#define CONF1_DS_BASE	64
+#define CONF1_IA_SHIFT	16			/* I$ associativity */
+#define CONF1_IA_MASK	0x00070000
+#define CONF1_IA_BASE	1
+#define CONF1_IL_SHIFT	19			/* I$ line size */
+#define CONF1_IL_MASK	0x00380000
+#define CONF1_IL_BASE	2
+#define CONF1_IS_SHIFT	22			/* Instruction cache sets/way */
+#define CONF1_IS_MASK	0x01c00000
+#define CONF1_IS_BASE	64
+
+#define Index_Invalidate_I	0x00
+#define Index_Writeback_Inv_D   0x01
+
+	.text
+	LEAF(startup)
+	.set noreorder
+	
+	/* Copy decompressor code to the right place */
+	li	t2, BZ_TEXT_START
+	add	a0, t2, 0
+	la      a1, code_start
+	la	a2, code_stop
+$L1:
+	lw	t0, 0(a1)
+	sw	t0, 0(a0)
+	add	a1, 4
+	add	a0, 4
+	blt	a1, a2, $L1
+	nop
+	
+	/* At this point we need to invalidate dcache and */
+	/* icache before jumping to new code */
+
+1:	/* Get cache sizes */
+	.set	mips32
+	mfc0	s0,C0_CONFIG,1
+	.set	mips0
+
+	li	s1,CONF1_DL_MASK
+	and	s1,s0
+	beq	s1,zero,nodc
+	nop
+
+	srl	s1,CONF1_DL_SHIFT
+	li	t0,CONF1_DL_BASE
+	sll	s1,t0,s1		/* s1 has D$ cache line size */
+
+	li	s2,CONF1_DA_MASK
+	and	s2,s0
+	srl	s2,CONF1_DA_SHIFT
+	addiu	s2,CONF1_DA_BASE	/* s2 now has D$ associativity */
+
+	li	t0,CONF1_DS_MASK
+	and	t0,s0
+	srl	t0,CONF1_DS_SHIFT
+	li	s3,CONF1_DS_BASE
+	sll	s3,s3,t0		/* s3 has D$ sets per way */
+
+	multu	s2,s3			/* sets/way * associativity */
+	mflo	t0			/* total cache lines */
+
+	multu	s1,t0			/* D$ linesize * lines */
+	mflo	s2			/* s2 is now D$ size in bytes */
+
+	/* Initilize the D$: */
+	mtc0	zero,C0_TAGLO
+	mtc0	zero,C0_TAGHI
+
+	li	t0,KSEG0		/* Just an address for the first $ line */
+	addu	t1,t0,s2		/*  + size of cache == end */
+
+	.set	mips3
+1:	cache	Index_Writeback_Inv_D,0(t0)
+	.set	mips0
+	bne	t0,t1,1b
+	addu	t0,s1
+	
+nodc:
+	/* Now we get to do it all again for the I$ */
+	
+	move	s3,zero			/* just in case there is no icache */
+	move	s4,zero
+
+	li	t0,CONF1_IL_MASK
+	and	t0,s0
+	beq	t0,zero,noic
+	nop
+
+	srl	t0,CONF1_IL_SHIFT
+	li	s3,CONF1_IL_BASE
+	sll	s3,t0			/* s3 has I$ cache line size */
+
+	li	t0,CONF1_IA_MASK
+	and	t0,s0
+	srl	t0,CONF1_IA_SHIFT
+	addiu	s4,t0,CONF1_IA_BASE	/* s4 now has I$ associativity */
+
+	li	t0,CONF1_IS_MASK
+	and	t0,s0
+	srl	t0,CONF1_IS_SHIFT
+	li	s5,CONF1_IS_BASE
+	sll	s5,t0			/* s5 has I$ sets per way */
+
+	multu	s4,s5			/* sets/way * associativity */
+	mflo	t0			/* s4 is now total cache lines */
+
+	multu	s3,t0			/* I$ linesize * lines */
+	mflo	s4			/* s4 is cache size in bytes */
+
+	/* Initilize the I$: */
+	mtc0	zero,C0_TAGLO
+	mtc0	zero,C0_TAGHI
+
+	li	t0,KSEG0		/* Just an address for the first $ line */
+	addu	t1,t0,s4		/*  + size of cache == end */
+
+	.set	mips3
+1:	cache	Index_Invalidate_I,0(t0)
+	.set	mips0
+	bne	t0,t1,1b
+	addu	t0,s3
+
+noic:
+	move	a0,s3			/* icache line size */
+	move	a1,s4			/* icache size */
+	move	a2,s1			/* dcache line size */
+	jal	t2
+	move	a3,s2			/* dcache size */
+	
+	.set reorder
+	END(startup)
diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/loader.lds.in b/target/linux/adm5120-2.6/image/lzma-loader/src/loader.lds.in
new file mode 100644
index 0000000000..20f2ea98ec
--- /dev/null
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/loader.lds.in
@@ -0,0 +1,17 @@
+OUTPUT_ARCH(mips)
+ENTRY(startup)
+SECTIONS {
+	. = TEXT_START;
+	.text : {
+		*(.text)
+		*(.rodata)
+	}
+
+	.data : {
+		*(.data)
+	}
+
+	.bss : {
+		*(.bss)
+	}
+}
diff --git a/target/linux/adm5120-2.6/patches/001-adm5120.patch b/target/linux/adm5120-2.6/patches/001-adm5120.patch
new file mode 100644
index 0000000000..11b4cba29b
--- /dev/null
+++ b/target/linux/adm5120-2.6/patches/001-adm5120.patch
@@ -0,0 +1,63 @@
+diff -urN linux-2.6.19.2/arch/mips/Kconfig linux-2.6.19.2.new/arch/mips/Kconfig
+--- linux-2.6.19.2/arch/mips/Kconfig	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2.new/arch/mips/Kconfig	2007-01-23 14:49:38.000000000 +0100
+@@ -12,6 +12,18 @@
+ 	prompt "System type"
+ 	default SGI_IP22
+ 
++config MIPS_ADM5120
++	bool "Support for ADM5120 SoC"
++	select SYS_HAS_CPU_MIPS32_R1
++	select DMA_NONCOHERENT
++	select HW_HAS_PCI
++	select SYS_SUPPORTS_LITTLE_ENDIAN
++	select SYS_SUPPORTS_32BIT_KERNEL
++
++config PCI_ADM5120
++	bool "Add PCI control support for ADM5120"
++	depends on MIPS_ADM5120 && PCI
++
+ config MIPS_MTX1
+ 	bool "4G Systems MTX-1 board"
+ 	select DMA_NONCOHERENT
+diff -urN linux-2.6.19.2/arch/mips/Makefile linux-2.6.19.2.new/arch/mips/Makefile
+--- linux-2.6.19.2/arch/mips/Makefile	2007-01-23 14:02:57.000000000 +0100
++++ linux-2.6.19.2.new/arch/mips/Makefile	2007-01-23 14:49:39.000000000 +0100
+@@ -165,6 +165,13 @@
+ load-$(CONFIG_MACH_JAZZ)	+= 0xffffffff80080000
+ 
+ #
++# ADMtek 5120
++#
++
++core-$(CONFIG_MIPS_ADM5120)	+= arch/mips/adm5120/
++load-$(CONFIG_MIPS_ADM5120)	+= 0xffffffff80001000
++
++#
+ # Common Alchemy Au1x00 stuff
+ #
+ core-$(CONFIG_SOC_AU1X00)	+= arch/mips/au1000/common/
+diff -urN linux-2.6.19.2/arch/mips/pci/Makefile linux-2.6.19.2.new/arch/mips/pci/Makefile
+--- linux-2.6.19.2/arch/mips/pci/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2.new/arch/mips/pci/Makefile	2007-01-23 14:49:40.000000000 +0100
+@@ -53,3 +53,4 @@
+ obj-$(CONFIG_VICTOR_MPC30X)	+= fixup-mpc30x.o
+ obj-$(CONFIG_ZAO_CAPCELLA)	+= fixup-capcella.o
+ obj-$(CONFIG_WR_PPMC)		+= fixup-wrppmc.o
++obj-$(CONFIG_PCI_ADM5120)	+= ops-adm5120.o pci-adm5120.o
+diff -urN linux-2.6.19.2/include/asm-mips/bootinfo.h linux-2.6.19.2.new/include/asm-mips/bootinfo.h
+--- linux-2.6.19.2/include/asm-mips/bootinfo.h	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2.new/include/asm-mips/bootinfo.h	2007-01-23 14:49:40.000000000 +0100
+@@ -212,6 +212,12 @@
+ #define MACH_GROUP_NEC_EMMA2RH 25	/* NEC EMMA2RH (was 23)		*/
+ #define  MACH_NEC_MARKEINS	0	/* NEC EMMA2RH Mark-eins	*/
+ 
++/*
++ * Valid machtype for group ADMtek
++ */
++#define MACH_GROUP_ADM_GW      23
++#define MACH_ADM_GW_5120	0
++
+ #define CL_SIZE			COMMAND_LINE_SIZE
+ 
+ const char *get_system_type(void);
diff --git a/target/linux/adm5120-2.6/patches/002-adm5120_flash.patch b/target/linux/adm5120-2.6/patches/002-adm5120_flash.patch
new file mode 100644
index 0000000000..503a49567c
--- /dev/null
+++ b/target/linux/adm5120-2.6/patches/002-adm5120_flash.patch
@@ -0,0 +1,25 @@
+diff -urN linux-2.6.19.2/drivers/mtd/maps/Kconfig linux-2.6.19.2-adm5120/drivers/mtd/maps/Kconfig
+--- linux-2.6.19.2/drivers/mtd/maps/Kconfig	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/mtd/maps/Kconfig	2007-01-23 01:13:39.000000000 +0100
+@@ -622,5 +622,10 @@
+ 
+ 	  This selection automatically selects the map_ram driver.
+ 
++config MTD_ADM5120
++	tristate "Map driver for ADMtek ADM5120 boards"
++	depends on MIPS_ADM5120
++	select MTD_CFI_AMDSTD
++
+ endmenu
+ 
+diff -urN linux-2.6.19.2/drivers/mtd/maps/Makefile linux-2.6.19.2-adm5120/drivers/mtd/maps/Makefile
+--- linux-2.6.19.2/drivers/mtd/maps/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/mtd/maps/Makefile	2007-01-23 01:20:52.000000000 +0100
+@@ -43,6 +43,7 @@
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI)		+= pci.o
+ obj-$(CONFIG_MTD_ALCHEMY)       += alchemy-flash.o
++obj-$(CONFIG_MTD_ADM5120)      	+= adm5120_mtd.o
+ obj-$(CONFIG_MTD_LASAT)		+= lasat.o
+ obj-$(CONFIG_MTD_AUTCPU12)	+= autcpu12-nvram.o
+ obj-$(CONFIG_MTD_EDB7312)	+= edb7312.o
diff --git a/target/linux/adm5120-2.6/patches/003-adm5120_switch.patch b/target/linux/adm5120-2.6/patches/003-adm5120_switch.patch
new file mode 100644
index 0000000000..f6fec30bca
--- /dev/null
+++ b/target/linux/adm5120-2.6/patches/003-adm5120_switch.patch
@@ -0,0 +1,25 @@
+diff -urN linux-2.6.19.2/drivers/net/Kconfig linux-2.6.19.2-adm5120/drivers/net/Kconfig
+--- linux-2.6.19.2/drivers/net/Kconfig	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/net/Kconfig	2007-01-23 01:13:39.000000000 +0100
+@@ -450,6 +450,10 @@
+ 	  If you have an Alchemy Semi AU1X00 based system
+ 	  say Y.  Otherwise, say N.
+ 
++config MIPS_ADM5120_ENET
++	tristate "MIPS ADM5120 Ethernet switch support"
++	depends on NET_ETHERNET && MIPS_ADM5120
++
+ config NET_SB1250_MAC
+ 	tristate "SB1250 Ethernet support"
+ 	depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC
+diff -urN linux-2.6.19.2/drivers/net/Makefile linux-2.6.19.2-adm5120/drivers/net/Makefile
+--- linux-2.6.19.2/drivers/net/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/net/Makefile	2007-01-23 01:13:39.000000000 +0100
+@@ -164,6 +164,7 @@
+ # This is also a 82596 and should probably be merged
+ obj-$(CONFIG_LP486E) += lp486e.o
+ 
++obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o
+ obj-$(CONFIG_ETH16I) += eth16i.o
+ obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
+ obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
diff --git a/target/linux/adm5120-2.6/patches/004-adm5120_uart.patch b/target/linux/adm5120-2.6/patches/004-adm5120_uart.patch
new file mode 100644
index 0000000000..c0bb0d37d7
--- /dev/null
+++ b/target/linux/adm5120-2.6/patches/004-adm5120_uart.patch
@@ -0,0 +1,43 @@
++config SERIAL_ADM5120
++	bool "ADM5120 serial port support"
++	depends on MIPS_ADM5120
++	select SERIAL_CORE
++	select SERIAL_CORE_CONSOLE
++	help
++	  Driver for the on chip UARTs on the ADM5120 SoC
++
++config ADM5120_NR_UARTS
++	int "Maximum number of ADM5120 serial ports"
++	depends on SERIAL_ADM5120
++	default "2"
++	---help---
++	  Set this to the number of serial ports you want the driver to
++	  support.
++
+ config SERIAL_AMBA_PL010
+ 	tristate "ARM AMBA PL010 serial port support"
+ 	depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
+diff -urN linux-2.6.19.2/drivers/serial/Makefile linux-2.6.19.2-adm5120/drivers/serial/Makefile
+--- linux-2.6.19.2/drivers/serial/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/serial/Makefile	2007-01-23 01:21:45.000000000 +0100
+@@ -20,6 +20,7 @@
+ obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
+ obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
+ obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
++obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o
+ obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
+ obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
+ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
+diff -urN linux-2.6.19.2/include/linux/serial_core.h linux-2.6.19.2-adm5120/include/linux/serial_core.h
+--- linux-2.6.19.2/include/linux/serial_core.h	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/include/linux/serial_core.h	2007-01-23 01:13:39.000000000 +0100
+@@ -133,6 +133,9 @@
+ #define PORT_S3C2412	73
+ 
+ 
++/* ADMtek ADM5120 SoC */
++#define PORT_ADM5120	68
++
+ #ifdef __KERNEL__
+ 
+ #include <linux/compiler.h>
diff --git a/target/linux/adm5120-2.6/patches/005-adm5120_usb.patch b/target/linux/adm5120-2.6/patches/005-adm5120_usb.patch
new file mode 100644
index 0000000000..40e4fbedf4
--- /dev/null
+++ b/target/linux/adm5120-2.6/patches/005-adm5120_usb.patch
@@ -0,0 +1,53 @@
+diff -urN linux-2.6.19.2/drivers/usb/core/hub.c linux-2.6.19.2-adm5120/drivers/usb/core/hub.c
+--- linux-2.6.19.2/drivers/usb/core/hub.c	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/usb/core/hub.c	2007-01-23 01:13:39.000000000 +0100
+@@ -2156,6 +2156,8 @@
+ 					USB_DT_DEVICE << 8, 0,
+ 					buf, GET_DESCRIPTOR_BUFSIZE,
+ 					(i ? USB_CTRL_GET_TIMEOUT : 1000));
++printk(KERN_CRIT "usb_control_msg: %d %d %d (%d)\n", r, buf->bMaxPacketSize0,
++buf->bDescriptorType, USB_DT_DEVICE);
+ 				switch (buf->bMaxPacketSize0) {
+ 				case 8: case 16: case 32: case 64: case 255:
+ 					if (buf->bDescriptorType ==
+diff -urN linux-2.6.19.2/drivers/usb/host/Kconfig linux-2.6.19.2-adm5120/drivers/usb/host/Kconfig
+--- linux-2.6.19.2/drivers/usb/host/Kconfig	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/usb/host/Kconfig	2007-01-23 01:13:39.000000000 +0100
+@@ -192,3 +192,6 @@
+ 	  To compile this driver as a module, choose M here: the
+ 	  module will be called "sl811_cs".
+ 
++config USB_ADM5120_HCD
++	tristate "ADM5120 HCD support"
++	depends on USB && MIPS_ADM5120
+diff -urN linux-2.6.19.2/drivers/usb/host/Makefile linux-2.6.19.2-adm5120/drivers/usb/host/Makefile
+--- linux-2.6.19.2/drivers/usb/host/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/usb/host/Makefile	2007-01-23 01:13:39.000000000 +0100
+@@ -16,3 +16,4 @@
+ obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
+ obj-$(CONFIG_USB_U132_HCD)	+= u132-hcd.o
+ obj-$(CONFIG_ETRAX_ARCH_V10)	+= hc_crisv10.o
++obj-$(CONFIG_USB_ADM5120_HCD)	+= adm5120-hcd.o
+diff -urN linux-2.6.19.2/drivers/usb/Kconfig linux-2.6.19.2-adm5120/drivers/usb/Kconfig
+--- linux-2.6.19.2/drivers/usb/Kconfig	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/usb/Kconfig	2007-01-23 01:13:39.000000000 +0100
+@@ -91,8 +91,6 @@
+ 
+ source "drivers/usb/net/Kconfig"
+ 
+-source "drivers/usb/mon/Kconfig"
+-
+ comment "USB port drivers"
+ 	depends on USB
+ 
+diff -urN linux-2.6.19.2/drivers/usb/Makefile linux-2.6.19.2-adm5120/drivers/usb/Makefile
+--- linux-2.6.19.2/drivers/usb/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/usb/Makefile	2007-01-23 01:22:18.000000000 +0100
+@@ -17,6 +17,7 @@
+ obj-$(CONFIG_USB_U132_HCD)	+= host/
+ obj-$(CONFIG_ETRAX_USB_HOST)	+= host/
+ obj-$(CONFIG_USB_OHCI_AT91)	+= host/
++obj-$(CONFIG_USB_ADM5120_HCD)  	+= host/
+ 
+ obj-$(CONFIG_USB_ACM)		+= class/
+ obj-$(CONFIG_USB_PRINTER)	+= class/
diff --git a/target/linux/adm5120-2.6/patches/006-adm5120_gpio.patch b/target/linux/adm5120-2.6/patches/006-adm5120_gpio.patch
new file mode 100644
index 0000000000..593743d7ba
--- /dev/null
+++ b/target/linux/adm5120-2.6/patches/006-adm5120_gpio.patch
@@ -0,0 +1,25 @@
+diff -urN linux-2.6.19.2/drivers/char/Kconfig linux-2.6.19.2-adm5120/drivers/char/Kconfig
+--- linux-2.6.19.2/drivers/char/Kconfig	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/char/Kconfig	2007-01-23 01:13:39.000000000 +0100
+@@ -1034,7 +1034,9 @@
+ 	  The mmtimer device allows direct userspace access to the
+ 	  Altix system timer.
+ 
+-source "drivers/char/tpm/Kconfig"
++config ADM5120_GPIO
++	tristate "ADM5120 GPIO"
++	depends on MIPS_ADM5120
+ 
+ config TELCLOCK
+ 	tristate "Telecom clock driver for MPBL0010 ATCA SBC"
+diff -urN linux-2.6.19.2/drivers/char/Makefile linux-2.6.19.2-adm5120/drivers/char/Makefile
+--- linux-2.6.19.2/drivers/char/Makefile	2007-01-10 20:10:37.000000000 +0100
++++ linux-2.6.19.2-adm5120/drivers/char/Makefile	2007-01-23 01:20:01.000000000 +0100
+@@ -90,6 +90,7 @@
+ obj-$(CONFIG_GPIO_VR41XX)	+= vr41xx_giu.o
+ obj-$(CONFIG_TANBAC_TB0219)	+= tb0219.o
+ obj-$(CONFIG_TELCLOCK)		+= tlclk.o
++obj-$(CONFIG_ADM5120_GPIO) 	+= adm5120_gpio.o
+ 
+ obj-$(CONFIG_WATCHDOG)		+= watchdog/
+ obj-$(CONFIG_MWAVE)		+= mwave/