ramips: add Netgear EX6150

SoC:   MediaTek MT7621
RAM:   64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi:  MediaTek MT7662E bgn 2SS
WiFi:  MediaTek MT7662E nac 2SS
BTN:   ON/OFF - Reset - WPS - AP/Extender toggle
LED:    - Arrow Right (blue)
        - Arrow Left (blue)
        - WiFi 1 (red/green)
        - WiFi 2 (red/green)
        - Power (green/amber)
        - WPS (Green)
UART:  UART is present as Pads on the backside of the PCB. They are
       located on the other side of the Ethernet port.
       3.3V - GND - TX - RX / 57600-8N1
       3.3V is the nearest one to the antenna connectors

Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).

You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash

Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>

3 files changed, 259 insertions, 0 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index f9f1e208f6..2df9259021 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -366,6 +366,7 @@ ramips_setup_interfaces()
 			"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6@eth0"
 		;;
 	dlink,dir-510l|\
+	netgear,ex6150|\
 	re350-v1)
 		ucidef_add_switch "switch0" \
 			"0:lan" "6@eth0"
diff --git a/target/linux/ramips/dts/EX6150.dts b/target/linux/ramips/dts/EX6150.dts
new file mode 100644
index 0000000000..729173bdd6
--- /dev/null
+++ b/target/linux/ramips/dts/EX6150.dts
@@ -0,0 +1,247 @@
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "netgear,ex6150", "mediatek,mt7621-soc";
+	model = "Netgear EX6150";
+
+	aliases {
+		led-boot = &power_green;
+		led-failsafe = &power_amber;
+		led-running = &power_green;
+		led-upgrade = &power_amber;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power_amber: power_amber {
+			label = "ex6150:amber:power";
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		power_green: power_green {
+			label = "ex6150:green:power";
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "ex6150:green:wps";
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		rightarrow {
+			label = "ex6150:blue:rightarrow";
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+
+		leftarrow {
+			label = "ex6150:blue:leftarrow";
+			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+		};
+
+		router_green {
+			label = "ex6150:green:router";
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		router_red {
+			label = "ex6150:red:router";
+			gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+		};
+
+		client_green {
+			label = "ex6150:green:client";
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		client_red {
+			label = "ex6150:red:client";
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		wps {
+			label = "wps";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		toggle {
+			label = "AP/Extender toggle";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			/* Active when switch is set to "Access Point" */
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "config";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition@40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0xe80000>;
+			};
+
+			partition@ed0000 {
+				label = "ML1";
+				reg = <0xed0000 0x10000>;
+				read-only;
+			};
+
+			partition@ef0000 {
+				label = "ML2";
+				reg = <0xef0000 0x20000>;
+				read-only;
+			};
+
+			partition@f10000 {
+				label = "ML3";
+				reg = <0xf10000 0x20000>;
+				read-only;
+			};
+
+			partition@f30000 {
+				label = "ML4";
+				reg = <0xf30000 0x20000>;
+				read-only;
+			};
+
+			partition@f50000 {
+				label = "ML5";
+				reg = <0xf50000 0x20000>;
+				read-only;
+			};
+
+			partition@f70000 {
+				label = "ML6";
+				reg = <0xf70000 0x20000>;
+				read-only;
+			};
+
+			partition@f90000 {
+				label = "ML7";
+				reg = <0xf90000 0x20000>;
+				read-only;
+			};
+
+			partition@fb0000 {
+				label = "T_Meter1";
+				reg = <0xfb0000 0x10000>;
+				read-only;
+			};
+
+			partition@fc0000 {
+				label = "T_Meter2";
+				reg = <0xfc0000 0x10000>;
+				read-only;
+			};
+
+			partition@fd0000 {
+				label = "POT";
+				reg = <0xfd0000 0x10000>;
+				read-only;
+			};
+
+			partition@fe0000 {
+				label = "board_data";
+				reg = <0xfe0000 0x10000>;
+				read-only;
+			};
+
+			partition@ff0000 {
+				label = "nvram";
+				reg = <0xff0000 0x10000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie0 {
+	wifi@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x8000>;
+		ieee80211-freq-limit = <5000000 6000000>;
+	};
+};
+
+&pcie1 {
+	wifi@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x0000>;
+		ieee80211-freq-limit = <2400000 2500000>;
+	};
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0x00000004>;
+};
+
+&pinctrl {
+	state_default: pinctrl0 {
+		gpio {
+			ralink,group = "sdhci", "rgmii2", "jtag";
+			ralink,function = "gpio";
+		};
+	};
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 1f514a6d04..b15dfacaf6 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -324,6 +324,17 @@ define Device/r6220
 endef
 TARGET_DEVICES += r6220
 
+define Device/netgear_ex6150
+  DTS := EX6150
+  DEVICE_TITLE := Netgear EX6150
+  DEVICE_PACKAGES := kmod-mt76x2 wpad-basic
+  NETGEAR_BOARD_ID := U12H318T00_NETGEAR
+  IMAGE_SIZE := 14848k
+  IMAGES += factory.chk
+  IMAGE/factory.chk := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | netgear-chk
+endef
+TARGET_DEVICES += netgear_ex6150
+
 define Device/netgear_r6350
   DTS := R6350
   BLOCKSIZE := 128k