ath79: add support for TP-Link Archer D7/D7b v1

TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.

The Archer D7b seems to differ from the Archer D7 only in the
partition table.

Router section - Specification:

775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB

Known issues:

- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
  OEM firmware works for both wifi interfaces; thus, this patch does
  not set a trigger by default)
- DSL not working (eth0)

UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX

J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX

The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.

Flash instructions under U-Boot, using UART
------------------------------------------
 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +f90000
	cp.b 0x81000000 0x9f020000 0xf90000
	reset

Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
	bootm 0x81000000
 4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
 4. Double check the .mod file size. It must be 16318464 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
	tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
	erase 0x9f020000 +f90000
	cp.b 0x81000000 0x9f020000 0xf90000
	reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

7 files changed, 390 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-d7-v1.dts b/target/linux/ath79/dts/qca9558_tplink_archer-d7-v1.dts
new file mode 100644
index 0000000000..8fae6545e3
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_tplink_archer-d7-v1.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9558_tplink_archer-d7.dtsi"
+
+/ {
+	compatible = "tplink,archer-d7-v1", "qca,qca9558";
+	model = "TP-Link Archer D7 v1";
+
+	aliases {
+		label-mac-device = &wmac;
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			partition@20000 {
+				compatible = "tplink,firmware";
+				label = "firmware";
+				reg = <0x020000 0xf90000>;
+			};
+
+			partition@fb0000 {
+				label = "radioDECT";
+				reg = <0xfb0000 0x010000>;
+				read-only;
+			};
+
+			partition@fc0000 {
+				label = "config";
+				reg = <0xfc0000 0x010000>;
+				read-only;
+			};
+
+			romfs: partition@fd0000 {
+				label = "romfs";
+				reg = <0xfd0000 0x010000>;
+				read-only;
+			};
+
+			partition@fe0000 {
+				label = "rom";
+				reg = <0xfe0000 0x010000>;
+				read-only;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	mtd-mac-address = <&romfs 0xf100>;
+	mtd-mac-address-increment = <1>;
+};
+
+&eth1 {
+	mtd-mac-address = <&romfs 0xf100>;
+};
+
+&wmac {
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&romfs 0xf100>;
+};
diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-d7.dtsi b/target/linux/ath79/dts/qca9558_tplink_archer-d7.dtsi
new file mode 100644
index 0000000000..a65d4e2b53
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_tplink_archer-d7.dtsi
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_system: system {
+			label = "tp-link:white:system";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wlan {
+			label = "tp-link:white:wlan";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "tp-link:white:lan";
+			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+		};
+
+		usb {
+			label = "tp-link:white:usb";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&hub_port1>, <&hub_port0>;
+			linux,default-trigger = "usbport";
+		};
+
+		qss {
+			label = "tp-link:white:qss";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		wifi {
+			label = "WiFi button";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_usb0_vbus: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb1_vbus: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+
+		qca,ar8327-initvals = <
+			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+			0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
+			0x50 0xc737c737 /* LED_CTRL0 */
+			0x54 0x00000000 /* LED_CTRL1 */
+			0x58 0x00000000 /* LED_CTRL2 */
+			0x5c 0x0030c300 /* LED_CTRL3 */
+			0x7c 0x0000007e /* PORT0_STATUS */
+			0x94 0x0000007e /* PORT6 STATUS */
+			>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&phy0>;
+	pll-data = <0x56000000 0x00000101 0x00001616>;
+
+	gmac-config {
+		device = <&gmac>;
+		rgmii-enabled = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	pll-data = <0x03000101 0x00000101 0x00001616>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&wmac {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dr_mode = "host";
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+
+	hub_port0: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dr_mode = "host";
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+
+	hub_port1: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
diff --git a/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts b/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts
new file mode 100644
index 0000000000..31563d9c46
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_tplink_archer-d7b-v1.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9558_tplink_archer-d7.dtsi"
+
+/ {
+	compatible = "tplink,archer-d7b-v1", "qca,qca9558";
+	model = "TP-Link Archer D7b v1";
+
+	aliases {
+		label-mac-device = &wmac;
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			partition@20000 {
+				compatible = "tplink,firmware";
+				label = "firmware";
+				reg = <0x020000 0xfa0000>;
+			};
+
+			partition@fc0000 {
+				label = "config";
+				reg = <0xfc0000 0x010000>;
+				read-only;
+			};
+
+			romfs: partition@fd0000 {
+				label = "romfs";
+				reg = <0xfd0000 0x010000>;
+				read-only;
+			};
+
+			partition@fe0000 {
+				label = "reserve";
+				reg = <0xfe0000 0x010000>;
+				read-only;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	mtd-mac-address = <&romfs 0xf100>;
+	mtd-mac-address-increment = <1>;
+};
+
+&eth1 {
+	mtd-mac-address = <&romfs 0xf100>;
+};
+
+&wmac {
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&romfs 0xf100>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 3864423e58..227ccf0dfe 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -187,6 +187,10 @@ tplink,archer-d50-v1)
 	ucidef_set_led_switch "wan_data" "WAN Data" "tp-link:white:internet" "switch0" "0x02" "" "tx rx"
 	ucidef_set_led_switch "wan_link" "WAN Link" "tp-link:white:wan" "switch0" "0x02" "" "link"
 	;;
+tplink,archer-d7-v1|\
+tplink,archer-d7b-v1)
+	ucidef_set_led_switch "lan" "LAN" "tp-link:white:lan" "switch0" "0x3c"
+	;;
 tplink,cpe210-v1|\
 tplink,cpe220-v2|\
 tplink,cpe220-v3|\
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 33a4b0e884..dbb722482b 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -252,6 +252,11 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan"
 		;;
+	tplink,archer-d7-v1|\
+	tplink,archer-d7b-v1)
+		ucidef_add_switch "switch0" \
+			"0@eth1" "3:lan:3" "4:lan:2" "5:lan:1" "6@eth0" "2:wan:4" "1:wan:5"
+		;;
 	tplink,tl-mr6400-v1)
 		ucidef_set_interfaces_lan_wan "eth0.1 eth1" "usb0"
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 43c2f9ced5..d354c7eaec 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -99,6 +99,11 @@ case "$FIRMWARE" in
 		caldata_extract "art" 0x5000 0x844
 		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2)
 		;;
+	tplink,archer-d7-v1|\
+	tplink,archer-d7b-v1)
+		caldata_extract "art" 0x5000 0x844
+		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfs 0xf100) +2)
+		;;
 	tplink,re350k-v1)
 		caldata_extract "art" 0x5000 0x844
 		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2)
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index ffa445697c..18f5233c09 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -217,6 +217,35 @@ define Device/tplink_archer-d50-v1
 endef
 TARGET_DEVICES += tplink_archer-d50-v1
 
+define Device/tplink_archer-d7-v1
+  $(Device/tplink-v2)
+  SOC := qca9558
+  DEVICE_MODEL := Archer D7
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport \
+	kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  IMAGE_SIZE := 15936k
+  TPLINK_HWID := 0x89300001
+  TPLINK_HWREV := 0x0000002D
+  TPLINK_FLASHLAYOUT := 16Mqca
+  TPLINK_HWREVADD := 0x00000002
+endef
+TARGET_DEVICES += tplink_archer-d7-v1
+
+define Device/tplink_archer-d7b-v1
+  $(Device/tplink-v2)
+  SOC := qca9558
+  DEVICE_MODEL := Archer D7b
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport \
+	kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  IMAGE_SIZE := 16000k
+  TPLINK_HWID := 0x89300001
+  TPLINK_HWREV := 0x0000003D
+  TPLINK_FLASHLAYOUT := 16Mqca
+endef
+TARGET_DEVICES += tplink_archer-d7b-v1
+
 define Device/tplink_cpe210-v1
   $(Device/tplink-safeloader-okli)
   SOC := ar9344