ipq806x: move dts file to the files folder

Signed-off-by: John Crispin <john@phrozen.org>

8 files changed, 1528 insertions, 1173 deletions

diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
new file mode 100644
index 0000000000..fc13637502
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
@@ -0,0 +1,412 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TP-Link Archer C2600";
+	compatible = "tplink,c2600", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+	};
+
+	chosen {
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			i2c4_pins: i2c4_pinmux {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				bias-disable;
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi4: spi@1a280000 {
+				status = "ok";
+				spi-max-frequency = <50000000>;
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 0>;
+
+				flash: m25p80@0 {
+					compatible = "s25fl256s1";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					SBL1@0 {
+						label = "SBL1";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+					MIBIB@20000 {
+						label = "MIBIB";
+						reg = <0x20000 0x20000>;
+						read-only;
+					};
+					SBL2@40000 {
+						label = "SBL2";
+						reg = <0x40000 0x20000>;
+						read-only;
+					};
+					SBL3@60000 {
+						label = "SBL3";
+						reg = <0x60000 0x30000>;
+						read-only;
+					};
+					DDRCONFIG@90000 {
+						label = "DDRCONFIG";
+						reg = <0x90000 0x10000>;
+						read-only;
+					};
+					SSD@a0000 {
+						label = "SSD";
+						reg = <0xa0000 0x10000>;
+						read-only;
+					};
+					TZ@b0000 {
+						label = "TZ";
+						reg = <0xb0000 0x30000>;
+						read-only;
+					};
+					RPM@e0000 {
+						label = "RPM";
+						reg = <0xe0000 0x20000>;
+						read-only;
+					};
+					fs-uboot@100000 {
+						label = "fs-uboot";
+						reg = <0x100000 0x70000>;
+						read-only;
+					};
+					uboot-env@170000 {
+						label = "uboot-env";
+						reg = <0x170000 0x40000>;
+						read-only;
+					};
+					radio@1b0000 {
+						label = "radio";
+						reg = <0x1b0000 0x40000>;
+						read-only;
+					};
+					os-image@1f0000 {
+						label = "os-image";
+						reg = <0x1f0000 0x200000>;
+					};
+					rootfs@3f0000 {
+						label = "rootfs";
+						reg = <0x3f0000 0x1b00000>;
+					};
+					defaultmac: default-mac@1ef0000 {
+						label = "default-mac";
+						reg = <0x1ef0000 0x00200>;
+						read-only;
+					};
+					pin@1ef0200 {
+						label = "pin";
+						reg = <0x1ef0200 0x00200>;
+						read-only;
+					};
+					product-info@1ef0400 {
+						label = "product-info";
+						reg = <0x1ef0400 0x0fc00>;
+						read-only;
+					};
+					partition-table@1f00000 {
+						label = "partition-table";
+						reg = <0x1f00000 0x10000>;
+						read-only;
+					};
+					soft-version@1f10000 {
+						label = "soft-version";
+						reg = <0x1f10000 0x10000>;
+						read-only;
+					};
+					support-list@1f20000 {
+						label = "support-list";
+						reg = <0x1f20000 0x10000>;
+						read-only;
+					};
+					profile@1f30000 {
+						label = "profile";
+						reg = <0x1f30000 0x10000>;
+						read-only;
+					};
+					default-config@1f40000 {
+						label = "default-config";
+						reg = <0x1f40000 0x10000>;
+						read-only;
+					};
+					user-config@1f50000 {
+						label = "user-config";
+						reg = <0x1f50000 0x40000>;
+						read-only;
+					};
+					qos-db@1f90000 {
+						label = "qos-db";
+						reg = <0x1f90000 0x40000>;
+						read-only;
+					};
+					usb-config@1fd0000 {
+						label = "usb-config";
+						reg = <0x1fd0000 0x10000>;
+						read-only;
+					};
+					log@1fe0000 {
+						label = "log";
+						reg = <0x1fe0000 0x20000>;
+						read-only;
+					};
+				};
+			};
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&defaultmac 0x8>;
+			mtd-mac-address-increment = <1>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&defaultmac 0x8>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 49 1>;
+			linux,code = <KEY_WLAN>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 64 1>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 1>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+                ledgeneral {
+			label = "ledgeneral";
+			gpios = <&qcom_pinmux 16 1>;
+			linux,code = <KEY_DOLLAR>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		lan {
+			label = "lan:blue";
+			gpios = <&qcom_pinmux 6 0>;
+		};
+                usb4 {
+			label = "usb_4:blue";
+			gpios = <&qcom_pinmux 7 0>;
+		};
+                usb2 {
+			label = "usb_2:blue";
+			gpios = <&qcom_pinmux 8 0>;
+		};
+                wps {
+			label = "wps:blue";
+			gpios = <&qcom_pinmux 9 0>;
+		};
+                wan_blue {
+			label = "wan:blue";
+			gpios = <&qcom_pinmux 33 1>;
+		};
+                status {
+			label = "status:blue";
+			gpios = <&qcom_pinmux 53 0>;
+			default-state = "on";
+		};
+                ledgnr {
+			label = "ledgnr:blue";
+			gpios = <&qcom_pinmux 66 0>;
+		};
+        };
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
new file mode 100644
index 0000000000..bd294c590e
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
@@ -0,0 +1,368 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 D7800";
+	compatible = "netgear,d7800", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			i2c4_pins: i2c4_pinmux {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				bias-disable;
+			};
+
+			pcie0_pins: pcie0_pinmux {
+				mux {
+					pins = "gpio3";
+					function = "pcie1_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			pcie1_pins: pcie1_pinmux {
+				mux {
+					pins = "gpio48";
+					function = "pcie2_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 0>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 0>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+		};
+
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			artbak: art@1340000 {
+				label = "artbak";
+				reg = <0x1340000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1480000 {
+				label = "kernel";
+				reg = <0x1480000 0x0200000>;
+			};
+
+			ubi@1680000 {
+				label = "ubi";
+				reg = <0x1680000 0x1E00000>;
+			};
+
+			netgear@3480000 {
+				label = "netgear";
+				reg = <0x3480000 0x4480000>;
+				read-only;
+			};
+
+			reserve@7900000 {
+				label = "reserve";
+				reg = <0x7900000 0x0700000>;
+				read-only;
+			};
+
+			firmware@1480000 {
+				label = "firmware";
+				reg = <0x1480000 0x2000000>;
+			};
+
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			phy-handle = <&phy4>;
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&art 6>;
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&art 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 1>;
+			linux,code = <KEY_WLAN>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 1>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 1>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		usb1 {
+			label = "d7800:amber:usb1";
+			gpios = <&qcom_pinmux 7 0>;
+		};
+
+		usb3 {
+			label = "d7800:amber:usb3";
+			gpios = <&qcom_pinmux 8 0>;
+		};
+
+		status {
+			label = "d7800:amber:status";
+			gpios = <&qcom_pinmux 9 0>;
+		};
+
+		internet {
+			label = "d7800:white:internet";
+			gpios = <&qcom_pinmux 22 0>;
+		};
+
+		wan {
+			label = "d7800:white:wan";
+			gpios = <&qcom_pinmux 23 0>;
+		};
+
+		wps {
+			label = "d7800:white:wps";
+			gpios = <&qcom_pinmux 24 0>;
+		};
+
+		esata {
+			label = "d7800:white:esata";
+			gpios = <&qcom_pinmux 26 0>;
+		};
+
+		power {
+			label = "d7800:white:power";
+			gpios = <&qcom_pinmux 53 0>;
+			default-state = "on";
+		};
+
+		rfkill {
+			label = "d7800:white:rfkill";
+			gpios = <&qcom_pinmux 64 0>;
+		};
+
+		wifi5g {
+			label = "d7800:white:wifi5g";
+			gpios = <&qcom_pinmux 67 0>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts
new file mode 100644
index 0000000000..2c5e1107a1
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts
@@ -0,0 +1,380 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Linksys EA8500 WiFi Router";
+	compatible = "linksys,ea8500", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200n8"; 
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			i2c4_pins: i2c4_pinmux {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				bias-disable;
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+			};
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+			
+			
+			
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+		
+		pcie2: pci@1b900000 {
+			status = "ok";
+			phy-tx0-term-offset = <7>;
+		};
+		
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			SBL1@0 {
+				label = "SBL1";
+				reg = <0x0000000 0x0040000>;
+				read-only;
+			};
+
+			MIBIB@40000 {
+				label = "MIBIB";
+				reg = <0x0040000 0x0140000>;
+				read-only;
+			};
+
+			SBL2@180000 {
+				label = "SBL2";
+				reg = <0x0180000 0x0140000>;
+				read-only;
+			};
+
+			SBL3@2c0000 {
+				label = "SBL3";
+				reg = <0x02c0000 0x0280000>;
+				read-only;
+			};
+
+			DDRCONFIG@540000 {
+				label = "DDRCONFIG";
+				reg = <0x0540000 0x0120000>;
+				read-only;
+			};
+
+			SSD@660000 {
+				label = "SSD";
+				reg = <0x0660000 0x0120000>;
+				read-only;
+			};
+			
+			TZ@780000 {
+				label = "TZ";
+				reg = <0x0780000 0x0280000>;
+				read-only;
+			};
+
+			RPM@a00000 {
+				label = "RPM";
+				reg = <0x0a00000 0x0280000>;
+				read-only;
+			};
+
+			art: art@c80000 {
+				label = "art";
+				reg = <0x0c80000 0x0140000>;
+				read-only;
+			};
+
+			APPSBL@dc0000 {
+				label = "APPSBL";
+				reg = <0x0dc0000 0x0100000>;
+				read-only;
+			};
+			
+			u_env@ec0000 {
+				label = "u_env";
+				reg = <0x0ec0000 0x0040000>;
+			};
+			
+			s_env@f00000 {
+				label = "s_env";
+				reg = <0x0f00000 0x0040000>;
+			};
+			
+			devinfo@f40000 {
+				label = "devinfo";
+				reg = <0x0f40000 0x0040000>;
+			};
+			
+			linux@f80000 { 
+				label = "kernel1";
+				reg = <0x0f80000 0x2800000>;  /* 3 MB spill to rootfs*/
+			};
+			
+			rootfs@1280000 {
+				label = "rootfs1";
+				reg = <0x1280000 0x2500000>;
+			};
+			
+			linux2@3780000 {
+				label = "kernel2";
+				reg = <0x3780000 0x2800000>;
+			};
+			
+			rootfs2@3a80000 {
+				label = "rootfs2";
+				reg = <0x3a80000 0x2500000>;
+			};
+			
+			syscfg@5f80000 {
+				label = "syscfg";
+				reg = <0x5f80000 0x2080000>;
+			};
+
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+			qcom,phy_mdio_addr = <4>;
+			qcom,poll_required = <1>;
+			qcom,rgmii_delay = <0>;
+			qcom,emulation = <0>;
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+		//lan
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+			qcom,phy_mdio_addr = <0>;	/* none */
+			qcom,poll_required = <0>;	/* no polling */
+			qcom,rgmii_delay = <0>;
+			qcom,emulation = <0>;
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		adm_dma: dma@18300000 {
+			status = "ok";
+		};
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		rfkill {
+			label = "rfkill"; /* WIFI on-off*/
+			gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART >;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		wps {
+			label = "ea8500:green:wps";
+			gpios = <&qcom_pinmux 53 0>;
+			default-state = "off";
+		};
+
+		power {
+			label = "ea8500:white:power";
+			gpios = <&qcom_pinmux 6 1>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+
+		wifi {
+			label = "ea8500:green:wifi";
+			gpios = <&qcom_pinmux 54 0>;
+			default-state = "off";
+		};
+	};
+};
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
new file mode 100644
index 0000000000..ca1f612844
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
@@ -0,0 +1,342 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear Nighthawk X4 R7500";
+	compatible = "netgear,r7500", "qcom,ipq8064";
+
+	memory@0 {
+		reg = <0x42000000 0xe000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			i2c4_pins: i2c4_pinmux {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				bias-disable;
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		sata-phy@1b400000 {
+			status = "ok";
+		};
+
+		sata@29000000 {
+			status = "ok";
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+		};
+
+		nand@1ac00000 {
+			status = "ok";
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			nand-ecc-strength = <4>;
+			nand-bus-width = <8>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcadata@0 {
+				label = "qcadata";
+				reg = <0x0000000 0x0c80000>;
+				read-only;
+			};
+
+			APPSBL@c80000 {
+				label = "APPSBL";
+				reg = <0x0c80000 0x0500000>;
+				read-only;
+			};
+
+			APPSBLENV@1180000 {
+				label = "APPSBLENV";
+				reg = <0x1180000 0x0080000>;
+				read-only;
+			};
+
+			art: art@1200000 {
+				label = "art";
+				reg = <0x1200000 0x0140000>;
+				read-only;
+			};
+
+			kernel@1340000 {
+				label = "kernel";
+				reg = <0x1340000 0x0200000>;
+			};
+
+			ubi@1540000 {
+				label = "ubi";
+				reg = <0x1540000 0x1800000>;
+			};
+
+			netgear@2d40000 {
+				label = "netgear";
+				reg = <0x2d40000 0x0c00000>;
+				read-only;
+			};
+
+			reserve@3940000 {
+				label = "reserve";
+				reg = <0x3940000 0x46c0000>;
+				read-only;
+			};
+
+			firmware@1340000 {
+				label = "firmware";
+				reg = <0x1340000 0x1a00000>;
+			};
+
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&art 6>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&art 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 1>;
+			linux,code = <KEY_WLAN>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 1>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 1>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		usb1 {
+			label = "r7500:amber:usb1";
+			gpios = <&qcom_pinmux 7 0>;
+		};
+
+		usb3 {
+			label = "r7500:amber:usb3";
+			gpios = <&qcom_pinmux 8 0>;
+		};
+
+		status {
+			label = "r7500:amber:status";
+			gpios = <&qcom_pinmux 9 0>;
+		};
+
+		internet {
+			label = "r7500:white:internet";
+			gpios = <&qcom_pinmux 22 0>;
+		};
+
+		wan {
+			label = "r7500:white:wan";
+			gpios = <&qcom_pinmux 23 0>;
+		};
+
+		wps {
+			label = "r7500:white:wps";
+			gpios = <&qcom_pinmux 24 0>;
+		};
+
+		esata {
+			label = "r7500:white:esata";
+			gpios = <&qcom_pinmux 26 0>;
+		};
+
+		power {
+			label = "r7500:white:power";
+			gpios = <&qcom_pinmux 53 0>;
+			default-state = "on";
+		};
+
+		rfkill {
+			label = "r7500:white:rfkill";
+			gpios = <&qcom_pinmux 64 0>;
+		};
+
+		wifi5g {
+			label = "r7500:white:wifi5g";
+			gpios = <&qcom_pinmux 67 0>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/patches-4.4/800-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch b/target/linux/ipq806x/patches-4.4/800-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch
deleted file mode 100644
index 1f5eba8377..0000000000
--- a/target/linux/ipq806x/patches-4.4/800-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch
+++ /dev/null
@@ -1,367 +0,0 @@
-From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 9 Aug 2015 13:02:38 +0200
-Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/arm/boot/dts/Makefile               |   1 +
- arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++
- 2 files changed, 371 insertions(+)
- create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -452,6 +452,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
- 	qcom-apq8084-mtp.dtb \
- 	qcom-ipq8064-ap148.dtb \
- 	qcom-ipq8064-db149.dtb \
-+	qcom-ipq8064-r7500.dtb \
- 	qcom-msm8660-surf.dtb \
- 	qcom-msm8960-cdp.dtb \
- 	qcom-msm8974-sony-xperia-honami.dtb
---- /dev/null
-+++ b/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
-@@ -0,0 +1,342 @@
-+#include "qcom-ipq8064-v1.0.dtsi"
-+
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+	model = "Netgear Nighthawk X4 R7500";
-+	compatible = "netgear,r7500", "qcom,ipq8064";
-+
-+	memory@0 {
-+		reg = <0x42000000 0xe000000>;
-+		device_type = "memory";
-+	};
-+
-+	reserved-memory {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		ranges;
-+		rsvd@41200000 {
-+			reg = <0x41200000 0x300000>;
-+			no-map;
-+		};
-+	};
-+
-+	aliases {
-+		serial0 = &uart4;
-+		mdio-gpio0 = &mdio0;
-+	};
-+
-+	chosen {
-+		bootargs = "rootfstype=squashfs noinitrd";
-+		linux,stdout-path = "serial0:115200n8";
-+	};
-+
-+	soc {
-+		pinmux@800000 {
-+			i2c4_pins: i2c4_pinmux {
-+				pins = "gpio12", "gpio13";
-+				function = "gsbi4";
-+				bias-disable;
-+			};
-+
-+			nand_pins: nand_pins {
-+				mux {
-+					pins = "gpio34", "gpio35", "gpio36",
-+					       "gpio37", "gpio38", "gpio39",
-+					       "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					function = "nand";
-+					drive-strength = <10>;
-+					bias-disable;
-+				};
-+				pullups {
-+					pins = "gpio39";
-+					bias-pull-up;
-+				};
-+				hold {
-+					pins = "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					bias-bus-hold;
-+				};
-+			};
-+
-+			mdio0_pins: mdio0_pins {
-+				mux {
-+					pins = "gpio0", "gpio1";
-+					function = "gpio";
-+					drive-strength = <8>;
-+					bias-disable;
-+				};
-+			};
-+
-+			rgmii2_pins: rgmii2_pins {
-+				mux {
-+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+					function = "rgmii2";
-+					drive-strength = <8>;
-+					bias-disable;
-+				};
-+			};
-+		};
-+
-+		gsbi@16300000 {
-+			qcom,mode = <GSBI_PROT_I2C_UART>;
-+			status = "ok";
-+			serial@16340000 {
-+				status = "ok";
-+			};
-+			/*
-+			 * The i2c device on gsbi4 should not be enabled.
-+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
-+			 * RPM usage. Turning this on in kernel manifests as
-+			 * i2c failure for the RPM.
-+			 */
-+		};
-+
-+		sata-phy@1b400000 {
-+			status = "ok";
-+		};
-+
-+		sata@29000000 {
-+			status = "ok";
-+		};
-+
-+		phy@100f8800 {		/* USB3 port 1 HS phy */
-+			status = "ok";
-+		};
-+
-+		phy@100f8830 {		/* USB3 port 1 SS phy */
-+			status = "ok";
-+		};
-+
-+		phy@110f8800 {		/* USB3 port 0 HS phy */
-+			status = "ok";
-+		};
-+
-+		phy@110f8830 {		/* USB3 port 0 SS phy */
-+			status = "ok";
-+		};
-+
-+		usb30@0 {
-+			status = "ok";
-+		};
-+
-+		usb30@1 {
-+			status = "ok";
-+		};
-+
-+		pcie0: pci@1b500000 {
-+			status = "ok";
-+		};
-+
-+		pcie1: pci@1b700000 {
-+			status = "ok";
-+		};
-+
-+		nand@1ac00000 {
-+			status = "ok";
-+
-+			pinctrl-0 = <&nand_pins>;
-+			pinctrl-names = "default";
-+
-+			nand-ecc-strength = <4>;
-+			nand-bus-width = <8>;
-+
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			qcadata@0 {
-+				label = "qcadata";
-+				reg = <0x0000000 0x0c80000>;
-+				read-only;
-+			};
-+
-+			APPSBL@c80000 {
-+				label = "APPSBL";
-+				reg = <0x0c80000 0x0500000>;
-+				read-only;
-+			};
-+
-+			APPSBLENV@1180000 {
-+				label = "APPSBLENV";
-+				reg = <0x1180000 0x0080000>;
-+				read-only;
-+			};
-+
-+			art: art@1200000 {
-+				label = "art";
-+				reg = <0x1200000 0x0140000>;
-+				read-only;
-+			};
-+
-+			kernel@1340000 {
-+				label = "kernel";
-+				reg = <0x1340000 0x0200000>;
-+			};
-+
-+			ubi@1540000 {
-+				label = "ubi";
-+				reg = <0x1540000 0x1800000>;
-+			};
-+
-+			netgear@2d40000 {
-+				label = "netgear";
-+				reg = <0x2d40000 0x0c00000>;
-+				read-only;
-+			};
-+
-+			reserve@3940000 {
-+				label = "reserve";
-+				reg = <0x3940000 0x46c0000>;
-+				read-only;
-+			};
-+
-+			firmware@1340000 {
-+				label = "firmware";
-+				reg = <0x1340000 0x1a00000>;
-+			};
-+
-+		};
-+
-+		mdio0: mdio {
-+			compatible = "virtual,mdio-gpio";
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+			pinctrl-0 = <&mdio0_pins>;
-+			pinctrl-names = "default";
-+
-+			phy0: ethernet-phy@0 {
-+				device_type = "ethernet-phy";
-+				reg = <0>;
-+				qca,ar8327-initvals = <
-+					0x00004 0x7600000   /* PAD0_MODE */
-+					0x00008 0x1000000   /* PAD5_MODE */
-+					0x0000c 0x80        /* PAD6_MODE */
-+					0x000e4 0xaa545     /* MAC_POWER_SEL */
-+					0x000e0 0xc74164de  /* SGMII_CTRL */
-+					0x0007c 0x4e        /* PORT0_STATUS */
-+					0x00094 0x4e        /* PORT6_STATUS */
-+					>;
-+			};
-+
-+			phy4: ethernet-phy@4 {
-+				device_type = "ethernet-phy";
-+				reg = <4>;
-+			};
-+		};
-+
-+		gmac1: ethernet@37200000 {
-+			status = "ok";
-+			phy-mode = "rgmii";
-+			qcom,id = <1>;
-+
-+			pinctrl-0 = <&rgmii2_pins>;
-+			pinctrl-names = "default";
-+
-+			mtd-mac-address = <&art 6>;
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
-+
-+		gmac2: ethernet@37400000 {
-+			status = "ok";
-+			phy-mode = "sgmii";
-+			qcom,id = <2>;
-+
-+			mtd-mac-address = <&art 0>;
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+
-+		wifi {
-+			label = "wifi";
-+			gpios = <&qcom_pinmux 6 1>;
-+			linux,code = <KEY_WLAN>;
-+		};
-+
-+		reset {
-+			label = "reset";
-+			gpios = <&qcom_pinmux 54 1>;
-+			linux,code = <KEY_RESTART>;
-+		};
-+
-+		wps {
-+			label = "wps";
-+			gpios = <&qcom_pinmux 65 1>;
-+			linux,code = <KEY_WPS_BUTTON>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		usb1 {
-+			label = "r7500:amber:usb1";
-+			gpios = <&qcom_pinmux 7 0>;
-+		};
-+
-+		usb3 {
-+			label = "r7500:amber:usb3";
-+			gpios = <&qcom_pinmux 8 0>;
-+		};
-+
-+		status {
-+			label = "r7500:amber:status";
-+			gpios = <&qcom_pinmux 9 0>;
-+		};
-+
-+		internet {
-+			label = "r7500:white:internet";
-+			gpios = <&qcom_pinmux 22 0>;
-+		};
-+
-+		wan {
-+			label = "r7500:white:wan";
-+			gpios = <&qcom_pinmux 23 0>;
-+		};
-+
-+		wps {
-+			label = "r7500:white:wps";
-+			gpios = <&qcom_pinmux 24 0>;
-+		};
-+
-+		esata {
-+			label = "r7500:white:esata";
-+			gpios = <&qcom_pinmux 26 0>;
-+		};
-+
-+		power {
-+			label = "r7500:white:power";
-+			gpios = <&qcom_pinmux 53 0>;
-+			default-state = "on";
-+		};
-+
-+		rfkill {
-+			label = "r7500:white:rfkill";
-+			gpios = <&qcom_pinmux 64 0>;
-+		};
-+
-+		wifi5g {
-+			label = "r7500:white:wifi5g";
-+			gpios = <&qcom_pinmux 67 0>;
-+		};
-+	};
-+};
-+
-+&adm_dma {
-+	status = "ok";
-+};
diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
new file mode 100644
index 0000000000..fc59837f66
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
@@ -0,0 +1,26 @@
+From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jogo@openwrt.org>
+Date: Sun, 9 Aug 2015 13:02:38 +0200
+Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree
+
+Signed-off-by: Jonas Gorski <jogo@openwrt.org>
+---
+ arch/arm/boot/dts/Makefile               |   1 +
+ arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++
+ 2 files changed, 371 insertions(+)
+ create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -506,7 +506,11 @@
+ 	qcom-apq8084-ifc6540.dtb \
+ 	qcom-apq8084-mtp.dtb \
+ 	qcom-ipq8064-ap148.dtb \
++	qcom-ipq8064-c2600.dtb \
++	qcom-ipq8064-d7800.dtb \
+ 	qcom-ipq8064-db149.dtb \
++	qcom-ipq8064-ea8500.dtb \
++	qcom-ipq8064-r7500.dtb \
+ 	qcom-msm8660-surf.dtb \
+ 	qcom-msm8960-cdp.dtb \
+ 	qcom-msm8974-sony-xperia-honami.dtb
diff --git a/target/linux/ipq806x/patches-4.4/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch b/target/linux/ipq806x/patches-4.4/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
deleted file mode 100644
index eaf037f57e..0000000000
--- a/target/linux/ipq806x/patches-4.4/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
+++ /dev/null
@@ -1,381 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -362,6 +362,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
- 	qcom-ipq8064-ap148.dtb \
- 	qcom-ipq8064-db149.dtb \
- 	qcom-ipq8064-r7500.dtb \
-+	qcom-ipq8064-d7800.dtb \
- 	qcom-msm8660-surf.dtb \
- 	qcom-msm8960-cdp.dtb \
- 	qcom-msm8974-sony-xperia-honami.dtb
---- /dev/null
-+++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
-@@ -0,0 +1,368 @@
-+#include "qcom-ipq8064-v1.0.dtsi"
-+
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+	model = "Netgear Nighthawk X4 D7800";
-+	compatible = "netgear,d7800", "qcom,ipq8064";
-+
-+	memory@0 {
-+		reg = <0x42000000 0xe000000>;
-+		device_type = "memory";
-+	};
-+
-+	reserved-memory {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		ranges;
-+		rsvd@41200000 {
-+			reg = <0x41200000 0x300000>;
-+			no-map;
-+		};
-+	};
-+
-+	aliases {
-+		serial0 = &uart4;
-+		mdio-gpio0 = &mdio0;
-+	};
-+
-+	chosen {
-+		bootargs = "rootfstype=squashfs noinitrd";
-+		linux,stdout-path = "serial0:115200n8";
-+	};
-+
-+	soc {
-+		pinmux@800000 {
-+			i2c4_pins: i2c4_pinmux {
-+				pins = "gpio12", "gpio13";
-+				function = "gsbi4";
-+				bias-disable;
-+			};
-+
-+			pcie0_pins: pcie0_pinmux {
-+				mux {
-+					pins = "gpio3";
-+					function = "pcie1_rst";
-+					drive-strength = <12>;
-+					bias-disable;
-+				};
-+			};
-+
-+			pcie1_pins: pcie1_pinmux {
-+				mux {
-+					pins = "gpio48";
-+					function = "pcie2_rst";
-+					drive-strength = <12>;
-+					bias-disable;
-+				};
-+			};
-+
-+			nand_pins: nand_pins {
-+				mux {
-+					pins = "gpio34", "gpio35", "gpio36",
-+					       "gpio37", "gpio38", "gpio39",
-+					       "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					function = "nand";
-+					drive-strength = <10>;
-+					bias-disable;
-+				};
-+				pullups {
-+					pins = "gpio39";
-+					bias-pull-up;
-+				};
-+				hold {
-+					pins = "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					bias-bus-hold;
-+				};
-+			};
-+
-+			mdio0_pins: mdio0_pins {
-+				mux {
-+					pins = "gpio0", "gpio1";
-+					function = "gpio";
-+					drive-strength = <8>;
-+					bias-disable;
-+				};
-+			};
-+
-+			rgmii2_pins: rgmii2_pins {
-+				mux {
-+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+					function = "rgmii2";
-+					drive-strength = <8>;
-+					bias-disable;
-+				};
-+			};
-+		};
-+
-+		gsbi@16300000 {
-+			qcom,mode = <GSBI_PROT_I2C_UART>;
-+			status = "ok";
-+			serial@16340000 {
-+				status = "ok";
-+			};
-+			/*
-+			 * The i2c device on gsbi4 should not be enabled.
-+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
-+			 * RPM usage. Turning this on in kernel manifests as
-+			 * i2c failure for the RPM.
-+			 */
-+		};
-+
-+		sata-phy@1b400000 {
-+			status = "ok";
-+		};
-+
-+		sata@29000000 {
-+			status = "ok";
-+		};
-+
-+		phy@100f8800 {		/* USB3 port 1 HS phy */
-+			status = "ok";
-+		};
-+
-+		phy@100f8830 {		/* USB3 port 1 SS phy */
-+			status = "ok";
-+		};
-+
-+		phy@110f8800 {		/* USB3 port 0 HS phy */
-+			status = "ok";
-+		};
-+
-+		phy@110f8830 {		/* USB3 port 0 SS phy */
-+			status = "ok";
-+		};
-+
-+		usb30@0 {
-+			status = "ok";
-+		};
-+
-+		usb30@1 {
-+			status = "ok";
-+		};
-+
-+		pcie0: pci@1b500000 {
-+			status = "ok";
-+			reset-gpio = <&qcom_pinmux 3 0>;
-+			pinctrl-0 = <&pcie0_pins>;
-+			pinctrl-names = "default";
-+		};
-+
-+		pcie1: pci@1b700000 {
-+			status = "ok";
-+			reset-gpio = <&qcom_pinmux 48 0>;
-+			pinctrl-0 = <&pcie1_pins>;
-+			pinctrl-names = "default";
-+		};
-+
-+		nand@1ac00000 {
-+			status = "ok";
-+
-+			pinctrl-0 = <&nand_pins>;
-+			pinctrl-names = "default";
-+
-+			nand-ecc-strength = <4>;
-+			nand-bus-width = <8>;
-+
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+
-+			qcadata@0 {
-+				label = "qcadata";
-+				reg = <0x0000000 0x0c80000>;
-+				read-only;
-+			};
-+
-+			APPSBL@c80000 {
-+				label = "APPSBL";
-+				reg = <0x0c80000 0x0500000>;
-+				read-only;
-+			};
-+
-+			APPSBLENV@1180000 {
-+				label = "APPSBLENV";
-+				reg = <0x1180000 0x0080000>;
-+				read-only;
-+			};
-+
-+			art: art@1200000 {
-+				label = "art";
-+				reg = <0x1200000 0x0140000>;
-+				read-only;
-+			};
-+
-+			artbak: art@1340000 {
-+				label = "artbak";
-+				reg = <0x1340000 0x0140000>;
-+				read-only;
-+			};
-+
-+			kernel@1480000 {
-+				label = "kernel";
-+				reg = <0x1480000 0x0200000>;
-+			};
-+
-+			ubi@1680000 {
-+				label = "ubi";
-+				reg = <0x1680000 0x1E00000>;
-+			};
-+
-+			netgear@3480000 {
-+				label = "netgear";
-+				reg = <0x3480000 0x4480000>;
-+				read-only;
-+			};
-+
-+			reserve@7900000 {
-+				label = "reserve";
-+				reg = <0x7900000 0x0700000>;
-+				read-only;
-+			};
-+
-+			firmware@1480000 {
-+				label = "firmware";
-+				reg = <0x1480000 0x2000000>;
-+			};
-+
-+		};
-+
-+		mdio0: mdio {
-+			compatible = "virtual,mdio-gpio";
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+			pinctrl-0 = <&mdio0_pins>;
-+			pinctrl-names = "default";
-+
-+			phy0: ethernet-phy@0 {
-+				device_type = "ethernet-phy";
-+				reg = <0>;
-+				qca,ar8327-initvals = <
-+					0x00004 0x7600000   /* PAD0_MODE */
-+					0x00008 0x1000000   /* PAD5_MODE */
-+					0x0000c 0x80        /* PAD6_MODE */
-+					0x000e4 0xaa545     /* MAC_POWER_SEL */
-+					0x000e0 0xc74164de  /* SGMII_CTRL */
-+					0x0007c 0x4e        /* PORT0_STATUS */
-+					0x00094 0x4e        /* PORT6_STATUS */
-+					>;
-+			};
-+
-+			phy4: ethernet-phy@4 {
-+				device_type = "ethernet-phy";
-+				reg = <4>;
-+			};
-+		};
-+
-+		gmac1: ethernet@37200000 {
-+			status = "ok";
-+			phy-mode = "rgmii";
-+			phy-handle = <&phy4>;
-+			qcom,id = <1>;
-+
-+			pinctrl-0 = <&rgmii2_pins>;
-+			pinctrl-names = "default";
-+
-+			mtd-mac-address = <&art 6>;
-+		};
-+
-+		gmac2: ethernet@37400000 {
-+			status = "ok";
-+			phy-mode = "sgmii";
-+			qcom,id = <2>;
-+
-+			mtd-mac-address = <&art 0>;
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+
-+		wifi {
-+			label = "wifi";
-+			gpios = <&qcom_pinmux 6 1>;
-+			linux,code = <KEY_WLAN>;
-+		};
-+
-+		reset {
-+			label = "reset";
-+			gpios = <&qcom_pinmux 54 1>;
-+			linux,code = <KEY_RESTART>;
-+		};
-+
-+		wps {
-+			label = "wps";
-+			gpios = <&qcom_pinmux 65 1>;
-+			linux,code = <KEY_WPS_BUTTON>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		usb1 {
-+			label = "d7800:amber:usb1";
-+			gpios = <&qcom_pinmux 7 0>;
-+		};
-+
-+		usb3 {
-+			label = "d7800:amber:usb3";
-+			gpios = <&qcom_pinmux 8 0>;
-+		};
-+
-+		status {
-+			label = "d7800:amber:status";
-+			gpios = <&qcom_pinmux 9 0>;
-+		};
-+
-+		internet {
-+			label = "d7800:white:internet";
-+			gpios = <&qcom_pinmux 22 0>;
-+		};
-+
-+		wan {
-+			label = "d7800:white:wan";
-+			gpios = <&qcom_pinmux 23 0>;
-+		};
-+
-+		wps {
-+			label = "d7800:white:wps";
-+			gpios = <&qcom_pinmux 24 0>;
-+		};
-+
-+		esata {
-+			label = "d7800:white:esata";
-+			gpios = <&qcom_pinmux 26 0>;
-+		};
-+
-+		power {
-+			label = "d7800:white:power";
-+			gpios = <&qcom_pinmux 53 0>;
-+			default-state = "on";
-+		};
-+
-+		rfkill {
-+			label = "d7800:white:rfkill";
-+			gpios = <&qcom_pinmux 64 0>;
-+		};
-+
-+		wifi5g {
-+			label = "d7800:white:wifi5g";
-+			gpios = <&qcom_pinmux 67 0>;
-+		};
-+	};
-+};
-+
-+&adm_dma {
-+	status = "ok";
-+};
diff --git a/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch b/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch
deleted file mode 100644
index 8952f3339d..0000000000
--- a/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch
+++ /dev/null
@@ -1,425 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -506,6 +506,7 @@
- 	qcom-apq8084-ifc6540.dtb \
- 	qcom-apq8084-mtp.dtb \
- 	qcom-ipq8064-ap148.dtb \
-+	qcom-ipq8064-c2600.dtb \
- 	qcom-ipq8064-db149.dtb \
- 	qcom-ipq8064-r7500.dtb \
- 	qcom-ipq8064-d7800.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
-@@ -0,0 +1,412 @@
-+#include "qcom-ipq8064-v1.0.dtsi"
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+	model = "TP-Link Archer C2600";
-+	compatible = "tplink,c2600", "qcom,ipq8064";
-+
-+	memory@0 {
-+		reg = <0x42000000 0x1e000000>;
-+		device_type = "memory";
-+	};
-+
-+	reserved-memory {
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		ranges;
-+		rsvd@41200000 {
-+			reg = <0x41200000 0x300000>;
-+			no-map;
-+		};
-+	};
-+
-+	aliases {
-+		serial0 = &uart4;
-+		mdio-gpio0 = &mdio0;
-+	};
-+
-+	chosen {
-+		linux,stdout-path = "serial0:115200n8";
-+	};
-+
-+	soc {
-+		pinmux@800000 {
-+			i2c4_pins: i2c4_pinmux {
-+				pins = "gpio12", "gpio13";
-+				function = "gsbi4";
-+				bias-disable;
-+			};
-+
-+			spi_pins: spi_pins {
-+				mux {
-+					pins = "gpio18", "gpio19", "gpio21";
-+					function = "gsbi5";
-+					drive-strength = <10>;
-+					bias-none;
-+				};
-+			};
-+
-+			nand_pins: nand_pins {
-+				mux {
-+					pins = "gpio34", "gpio35", "gpio36",
-+					       "gpio37", "gpio38", "gpio39",
-+					       "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					function = "nand";
-+					drive-strength = <10>;
-+					bias-disable;
-+				};
-+
-+				pullups {
-+					pins = "gpio39";
-+					bias-pull-up;
-+				};
-+
-+				hold {
-+					pins = "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					bias-bus-hold;
-+				};
-+			};
-+
-+			mdio0_pins: mdio0_pins {
-+				mux {
-+					pins = "gpio0", "gpio1";
-+					function = "gpio";
-+					drive-strength = <8>;
-+					bias-disable;
-+				};
-+			};
-+
-+			rgmii2_pins: rgmii2_pins {
-+				mux {
-+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+					function = "rgmii2";
-+					drive-strength = <8>;
-+					bias-disable;
-+				};
-+			};
-+		};
-+
-+		gsbi@16300000 {
-+			qcom,mode = <GSBI_PROT_I2C_UART>;
-+			status = "ok";
-+			serial@16340000 {
-+				status = "ok";
-+			};
-+			/*
-+			 * The i2c device on gsbi4 should not be enabled.
-+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
-+			 * RPM usage. Turning this on in kernel manifests as
-+			 * i2c failure for the RPM.
-+			 */
-+		};
-+
-+		gsbi5: gsbi@1a200000 {
-+			qcom,mode = <GSBI_PROT_SPI>;
-+			status = "ok";
-+
-+			spi4: spi@1a280000 {
-+				status = "ok";
-+				spi-max-frequency = <50000000>;
-+
-+				pinctrl-0 = <&spi_pins>;
-+				pinctrl-names = "default";
-+
-+				cs-gpios = <&qcom_pinmux 20 0>;
-+
-+				flash: m25p80@0 {
-+					compatible = "s25fl256s1";
-+					#address-cells = <1>;
-+					#size-cells = <1>;
-+					spi-max-frequency = <50000000>;
-+					reg = <0>;
-+
-+					SBL1@0 {
-+						label = "SBL1";
-+						reg = <0x0 0x20000>;
-+						read-only;
-+					};
-+					MIBIB@20000 {
-+						label = "MIBIB";
-+						reg = <0x20000 0x20000>;
-+						read-only;
-+					};
-+					SBL2@40000 {
-+						label = "SBL2";
-+						reg = <0x40000 0x20000>;
-+						read-only;
-+					};
-+					SBL3@60000 {
-+						label = "SBL3";
-+						reg = <0x60000 0x30000>;
-+						read-only;
-+					};
-+					DDRCONFIG@90000 {
-+						label = "DDRCONFIG";
-+						reg = <0x90000 0x10000>;
-+						read-only;
-+					};
-+					SSD@a0000 {
-+						label = "SSD";
-+						reg = <0xa0000 0x10000>;
-+						read-only;
-+					};
-+					TZ@b0000 {
-+						label = "TZ";
-+						reg = <0xb0000 0x30000>;
-+						read-only;
-+					};
-+					RPM@e0000 {
-+						label = "RPM";
-+						reg = <0xe0000 0x20000>;
-+						read-only;
-+					};
-+					fs-uboot@100000 {
-+						label = "fs-uboot";
-+						reg = <0x100000 0x70000>;
-+						read-only;
-+					};
-+					uboot-env@170000 {
-+						label = "uboot-env";
-+						reg = <0x170000 0x40000>;
-+						read-only;
-+					};
-+					radio@1b0000 {
-+						label = "radio";
-+						reg = <0x1b0000 0x40000>;
-+						read-only;
-+					};
-+					os-image@1f0000 {
-+						label = "os-image";
-+						reg = <0x1f0000 0x200000>;
-+					};
-+					rootfs@3f0000 {
-+						label = "rootfs";
-+						reg = <0x3f0000 0x1b00000>;
-+					};
-+					defaultmac: default-mac@1ef0000 {
-+						label = "default-mac";
-+						reg = <0x1ef0000 0x00200>;
-+						read-only;
-+					};
-+					pin@1ef0200 {
-+						label = "pin";
-+						reg = <0x1ef0200 0x00200>;
-+						read-only;
-+					};
-+					product-info@1ef0400 {
-+						label = "product-info";
-+						reg = <0x1ef0400 0x0fc00>;
-+						read-only;
-+					};
-+					partition-table@1f00000 {
-+						label = "partition-table";
-+						reg = <0x1f00000 0x10000>;
-+						read-only;
-+					};
-+					soft-version@1f10000 {
-+						label = "soft-version";
-+						reg = <0x1f10000 0x10000>;
-+						read-only;
-+					};
-+					support-list@1f20000 {
-+						label = "support-list";
-+						reg = <0x1f20000 0x10000>;
-+						read-only;
-+					};
-+					profile@1f30000 {
-+						label = "profile";
-+						reg = <0x1f30000 0x10000>;
-+						read-only;
-+					};
-+					default-config@1f40000 {
-+						label = "default-config";
-+						reg = <0x1f40000 0x10000>;
-+						read-only;
-+					};
-+					user-config@1f50000 {
-+						label = "user-config";
-+						reg = <0x1f50000 0x40000>;
-+						read-only;
-+					};
-+					qos-db@1f90000 {
-+						label = "qos-db";
-+						reg = <0x1f90000 0x40000>;
-+						read-only;
-+					};
-+					usb-config@1fd0000 {
-+						label = "usb-config";
-+						reg = <0x1fd0000 0x10000>;
-+						read-only;
-+					};
-+					log@1fe0000 {
-+						label = "log";
-+						reg = <0x1fe0000 0x20000>;
-+						read-only;
-+					};
-+				};
-+			};
-+		};
-+
-+		phy@100f8800 {		/* USB3 port 1 HS phy */
-+			status = "ok";
-+		};
-+
-+		phy@100f8830 {		/* USB3 port 1 SS phy */
-+			status = "ok";
-+		};
-+
-+		phy@110f8800 {		/* USB3 port 0 HS phy */
-+			status = "ok";
-+		};
-+
-+		phy@110f8830 {		/* USB3 port 0 SS phy */
-+			status = "ok";
-+		};
-+
-+		usb30@0 {
-+			status = "ok";
-+		};
-+
-+		usb30@1 {
-+			status = "ok";
-+		};
-+
-+		pcie0: pci@1b500000 {
-+			status = "ok";
-+			phy-tx0-term-offset = <7>;
-+		};
-+
-+		pcie1: pci@1b700000 {
-+			status = "ok";
-+			phy-tx0-term-offset = <7>;
-+		};
-+
-+		mdio0: mdio {
-+			compatible = "virtual,mdio-gpio";
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+			pinctrl-0 = <&mdio0_pins>;
-+			pinctrl-names = "default";
-+
-+			phy0: ethernet-phy@0 {
-+				device_type = "ethernet-phy";
-+				reg = <0>;
-+				qca,ar8327-initvals = <
-+					0x00004 0x7600000   /* PAD0_MODE */
-+					0x00008 0x1000000   /* PAD5_MODE */
-+					0x0000c 0x80        /* PAD6_MODE */
-+					0x000e4 0xaa545     /* MAC_POWER_SEL */
-+					0x000e0 0xc74164de  /* SGMII_CTRL */
-+					0x0007c 0x4e        /* PORT0_STATUS */
-+					0x00094 0x4e        /* PORT6_STATUS */
-+					>;
-+			};
-+
-+			phy4: ethernet-phy@4 {
-+				device_type = "ethernet-phy";
-+				reg = <4>;
-+			};
-+		};
-+
-+		gmac1: ethernet@37200000 {
-+			status = "ok";
-+			phy-mode = "rgmii";
-+			qcom,id = <1>;
-+
-+			pinctrl-0 = <&rgmii2_pins>;
-+			pinctrl-names = "default";
-+
-+			mtd-mac-address = <&defaultmac 0x8>;
-+			mtd-mac-address-increment = <1>;
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
-+
-+		gmac2: ethernet@37400000 {
-+			status = "ok";
-+			phy-mode = "sgmii";
-+			qcom,id = <2>;
-+
-+			mtd-mac-address = <&defaultmac 0x8>;
-+
-+			fixed-link {
-+				speed = <1000>;
-+				full-duplex;
-+			};
-+		};
-+	};
-+
-+	gpio-keys {
-+		compatible = "gpio-keys";
-+
-+		wifi {
-+			label = "wifi";
-+			gpios = <&qcom_pinmux 49 1>;
-+			linux,code = <KEY_WLAN>;
-+		};
-+
-+		reset {
-+			label = "reset";
-+			gpios = <&qcom_pinmux 64 1>;
-+			linux,code = <KEY_RESTART>;
-+		};
-+
-+		wps {
-+			label = "wps";
-+			gpios = <&qcom_pinmux 65 1>;
-+			linux,code = <KEY_WPS_BUTTON>;
-+		};
-+                ledgeneral {
-+			label = "ledgeneral";
-+			gpios = <&qcom_pinmux 16 1>;
-+			linux,code = <KEY_DOLLAR>;
-+		};
-+	};
-+
-+	gpio-leds {
-+		compatible = "gpio-leds";
-+
-+		lan {
-+			label = "lan:blue";
-+			gpios = <&qcom_pinmux 6 0>;
-+		};
-+                usb4 {
-+			label = "usb_4:blue";
-+			gpios = <&qcom_pinmux 7 0>;
-+		};
-+                usb2 {
-+			label = "usb_2:blue";
-+			gpios = <&qcom_pinmux 8 0>;
-+		};
-+                wps {
-+			label = "wps:blue";
-+			gpios = <&qcom_pinmux 9 0>;
-+		};
-+                wan_blue {
-+			label = "wan:blue";
-+			gpios = <&qcom_pinmux 33 1>;
-+		};
-+                status {
-+			label = "status:blue";
-+			gpios = <&qcom_pinmux 53 0>;
-+			default-state = "on";
-+		};
-+                ledgnr {
-+			label = "ledgnr:blue";
-+			gpios = <&qcom_pinmux 66 0>;
-+		};
-+        };
-+};
-+
-+&adm_dma {
-+	status = "ok";
-+};