ath79: add support for OpenMesh OM2P-HS v1

Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[drop redundant status from eth1]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

7 files changed, 182 insertions, 1 deletions

diff --git a/package/boot/uboot-envtools/Makefile b/package/boot/uboot-envtools/Makefile
index 539e65e762..3493332cee 100644
--- a/package/boot/uboot-envtools/Makefile
+++ b/package/boot/uboot-envtools/Makefile
@@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk
 PKG_NAME:=uboot-envtools
 PKG_DISTNAME:=u-boot
 PKG_VERSION:=2020.04
-PKG_RELEASE:=11
+PKG_RELEASE:=12
 
 PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2
 PKG_SOURCE_URL:= \
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index a7564bc89e..bc69d35c96 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -86,6 +86,7 @@ netgear,wndr4300sw)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000"
 	;;
 openmesh,om2p-v4|\
+openmesh,om2p-hs-v1|\
 openmesh,om2p-hs-v4|\
 plasmacloud,pa300|\
 plasmacloud,pa300e)
diff --git a/target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts
new file mode 100644
index 0000000000..e1f14cd5c2
--- /dev/null
+++ b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs-v1.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9341_openmesh_om2p-hs.dtsi"
+
+/ {
+	compatible = "openmesh,om2p-hs-v1", "qca,ar9341";
+	model = "OpenMesh OM2P-HS v1";
+};
diff --git a/target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi
new file mode 100644
index 0000000000..403ee940c1
--- /dev/null
+++ b/target/linux/ath79/dts/ar9341_openmesh_om2p-hs.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9341.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		/delete-property/ bootargs;
+	};
+
+	aliases {
+		serial0 = &uart;
+		led-boot = &led_power_blue;
+		led-failsafe = &led_power_blue;
+		led-running = &led_power_blue;
+		led-upgrade = &led_power_blue;
+		label-mac-device = &eth1;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&jtag_disable_pins &led_lan_wan_blue_pin>;
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power_blue: power_blue {
+			label = "blue:power";
+			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wifi_green {
+			label = "green:wifi";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wifi_red {
+			label = "red:wifi";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi_yellow {
+			label = "yellow:wifi";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+
+		lan_blue {
+			label = "blue:lan";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+
+		wan_blue {
+			label = "blue:wan";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	watchdog {
+		compatible = "linux,wdt-gpio";
+		gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		hw_algo = "toggle";
+		/* hw_margin_ms is actually 300s but driver limits it to 60s */
+		hw_margin_ms = <60000>;
+		always-running;
+	};
+};
+
+&ref {
+	clock-frequency = <40000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&pinmux {
+	led_lan_wan_blue_pin: pinmux_lan_wan_blue_pin {
+		pinctrl-single,bits = <0x10 0x0 0x0000ffff>;
+	};
+};
+
+&spi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		/* partitions are passed via bootloader */
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x040000>;
+			};
+
+			partition@80000 {
+				label = "custom";
+				reg = <0x080000 0x140000>;
+				read-only;
+			};
+
+			partition@1c0000 {
+				label = "inactive";
+				reg = <0x1c0000 0x700000>;
+			};
+
+			partition@8c0000 {
+				label = "inactive2";
+				reg = <0x8c0000 0x700000>;
+			};
+
+			art: partition@fc0000 {
+				label = "ART";
+				reg = <0xfc0000 0x040000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&swphy4>;
+
+	mtd-mac-address = <&art 0x6>;
+};
+
+&eth1 {
+	mtd-mac-address = <&art 0x0>;
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 5795e2a0ae..057bec3bc8 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -145,6 +145,7 @@ comfast,cf-e560ac)
 	ucidef_set_led_switch "lan4" "LAN4" "blue:lan4" "switch0" "0x10"
 	;;
 comfast,cf-ew72|\
+openmesh,om2p-hs-v1|\
 telco,t1)
 	ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
 	ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index 6f0ab8f8a6..e3298cfc13 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -51,6 +51,7 @@ platform_do_upgrade() {
 		redboot_fis_do_upgrade "$1" linux
 		;;
 	openmesh,om2p-v4|\
+	openmesh,om2p-hs-v1|\
 	openmesh,om2p-hs-v4)
 		PART_NAME="inactive"
 		platform_do_upgrade_openmesh "$1"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 66a39e06d2..1454c14e44 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1577,6 +1577,15 @@ define Device/openmesh_om2p-v4
 endef
 TARGET_DEVICES += openmesh_om2p-v4
 
+define Device/openmesh_om2p-hs-v1
+  $(Device/openmesh_om2p-common)
+  SOC := ar9341
+  DEVICE_MODEL := OM2P-HS
+  DEVICE_VARIANT := v1
+  SUPPORTED_DEVICES += om2p-hs
+endef
+TARGET_DEVICES += openmesh_om2p-hs-v1
+
 define Device/openmesh_om2p-hs-v4
   $(Device/openmesh_om2p-common)
   SOC := qca9533