ar71xx: register rtl8366-smi device on the DIR-825 B1 board

SVN-Revision: 18710

1 files changed, 21 insertions, 4 deletions

diff --git a/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir-825-b1.c b/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir-825-b1.c
index ae95febd36..4fdb9fb5b4 100644
--- a/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir-825-b1.c
+++ b/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir-825-b1.c
@@ -19,6 +19,7 @@
 #include <linux/pci.h>
 #include <linux/ath9k_platform.h>
 #include <linux/delay.h>
+#include <linux/rtl8366_smi.h>
 
 #include <asm/mips_machine.h>
 #include <asm/mach-ar71xx/ar71xx.h>
@@ -36,6 +37,9 @@
 #define DIR825B1_GPIO_BTN_RESET			3
 #define DIR825B1_GPIO_BTN_POWERSAVE		8
 
+#define DIR825B1_GPIO_RTL8366_SDA		5
+#define DIR825B1_GPIO_RTL8366_SCK		7
+
 #define DIR825B1_BUTTONS_POLL_INTERVAL		20
 
 #define DIR825B1_CAL_LOCATION_0			0x1f661000
@@ -137,6 +141,19 @@ static struct gpio_button dir825b1_gpio_buttons[] __initdata = {
 	}
 };
 
+static struct rtl8366_smi_platform_data dir825b1_rtl8366_smi_data = {
+	.gpio_sda        = DIR825B1_GPIO_RTL8366_SDA,
+	.gpio_sck        = DIR825B1_GPIO_RTL8366_SCK,
+};
+
+static struct platform_device dir825b1_rtl8366_smi_device = {
+	.name		= "rtl8366-smi",
+	.id		= -1,
+	.dev = {
+		.platform_data	= &dir825b1_rtl8366_smi_data,
+	}
+};
+
 #ifdef CONFIG_PCI
 static struct ar71xx_pci_irq dir825b1_pci_irqs[] __initdata = {
         {
@@ -267,16 +284,15 @@ static void __init dir825b1_setup(void)
 
 	ar71xx_add_device_mdio(0x0);
 
+	ar71xx_eth0_data.mii_bus_dev = &dir825b1_rtl8366_smi_device.dev;
 	ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
-	ar71xx_eth0_data.phy_mask = 0x1e;
 	ar71xx_eth0_data.speed = SPEED_1000;
 	ar71xx_eth0_data.duplex = DUPLEX_FULL;
 	ar71xx_eth0_pll_data.pll_1000 = 0x11110000;
 
+	ar71xx_eth1_data.mii_bus_dev = &dir825b1_rtl8366_smi_device.dev;
 	ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
-	ar71xx_eth1_data.phy_mask = 0xc0;
-	ar71xx_eth1_data.speed = SPEED_1000;
-	ar71xx_eth1_data.duplex = DUPLEX_FULL;
+	ar71xx_eth1_data.phy_mask = 0x10;
 	ar71xx_eth1_pll_data.pll_1000 = 0x11110000;
 
 	ar71xx_add_device_eth(0);
@@ -294,6 +310,7 @@ static void __init dir825b1_setup(void)
 
 	ar71xx_add_device_usb();
 
+	platform_device_register(&dir825b1_rtl8366_smi_device);
 	dir825b1_pci_init();
 }