aboutsummaryrefslogtreecommitdiffstats
path: root/.gitignore
diff options
context:
space:
mode:
authorINAGAKI Hiroshi <musashino.open@gmail.com>2023-03-08 21:54:14 +0900
committerHauke Mehrtens <hauke@hauke-m.de>2023-03-08 23:49:39 +0100
commit102dc5a6250608f8324ce20174e8a07523f98bcc (patch)
treed29dfc6a523e247f992762c0ab949b431a3b905d /.gitignore
parentd45659a571645f98674845e5efd07f447de337ed (diff)
downloadupstream-102dc5a6250608f8324ce20174e8a07523f98bcc.tar.gz
upstream-102dc5a6250608f8324ce20174e8a07523f98bcc.tar.bz2
upstream-102dc5a6250608f8324ce20174e8a07523f98bcc.zip
mvebu: add support for Fortinet FortiGate 50E
Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-50E and interrupt to show bootmenu 2. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 3. Prepare TFTP server with the parameters obtained above 4. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 6. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 7. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 7. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 8. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of WAN1/2 are connected to GPIO expander. There is no way to indicate link speed of networking device on Linux Kernel/OpenWrt, so those LEDs cannot be handled like stock firmware. On OpenWrt, use netdev(link) trigger instead. - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex)) WAN 1 : 70:4C:A5:xx:xx:7D WAN 2 : 70:4C:A5:xx:xx:7E LAN 1 : 70:4C:A5:xx:xx:7F LAN 2 : 70:4C:A5:xx:xx:80 LAN 3 : 70:4C:A5:xx:xx:81 LAN 4 : 70:4C:A5:xx:xx:82 LAN 5 : 70:4C:A5:xx:xx:83 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Diffstat (limited to '.gitignore')
0 files changed, 0 insertions, 0 deletions