From 716ca530e1c4515d8683c9d5be3d56b301758b66 Mon Sep 17 00:00:00 2001
From: James <>
Date: Wed, 4 Nov 2015 11:49:21 +0000
Subject: trunk-47381

---
 .../202-dt-sun7i-add-bluetooth-to-cubietruck.patch | 75 ++++++++++++++++++++++
 1 file changed, 75 insertions(+)
 create mode 100644 target/linux/sunxi/patches-4.1/202-dt-sun7i-add-bluetooth-to-cubietruck.patch

(limited to 'target/linux/sunxi/patches-4.1/202-dt-sun7i-add-bluetooth-to-cubietruck.patch')

diff --git a/target/linux/sunxi/patches-4.1/202-dt-sun7i-add-bluetooth-to-cubietruck.patch b/target/linux/sunxi/patches-4.1/202-dt-sun7i-add-bluetooth-to-cubietruck.patch
new file mode 100644
index 0000000..ae5576f
--- /dev/null
+++ b/target/linux/sunxi/patches-4.1/202-dt-sun7i-add-bluetooth-to-cubietruck.patch
@@ -0,0 +1,75 @@
+From c6e2b7dad39a7887f935458d1c8de84db06243e1 Mon Sep 17 00:00:00 2001
+From: Chen-Yu Tsai <wens@csie.org>
+Date: Thu, 26 Dec 2013 17:15:47 +0800
+Subject: [PATCH] ARM: dts: sun7i: add bluetooth module to CubieTruck DTS
+
+The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The
+Bluetooth part is a BCM20710 IC connected to UART2 in the A20
+SoC. The IC also takes a 32.768 KHz low power clock input, a power
+enable signal and a wake signal via GPIO.
+
+The Bluetooth module supports out-of-band interrupt signaling via
+GPIO, but this is not supported in this patch.
+---
+ arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 36 ++++++++++++++++++++++++++++++
+ 1 file changed, 36 insertions(+)
+
+--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
++++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+@@ -88,6 +88,20 @@
+ 				interrupts = <10 8>; /* PH10 / EINT10 */
+ 				interrupt-names = "host-wake";
+ 			};
++
++			bt_pwr_pin: bt_pwr_pin@0 {
++				allwinner,pins = "PH18";
++				allwinner,function = "gpio_out";
++				allwinner,drive = <0>;
++				allwinner,pull = <0>;
++			};
++
++			bt_wake_pin: bt_wake_pin@0 {
++				allwinner,pins = "PH24";
++				allwinner,function = "gpio_out";
++				allwinner,drive = <0>;
++				allwinner,pull = <0>;
++			};
+ 		};
+ 
+ 		usbphy: phy@01c13400 {
+@@ -171,6 +185,12 @@
+ 			status = "okay";
+ 		};
+ 
++		uart2: serial@01c28800 {
++			pinctrl-names = "default";
++			pinctrl-0 = <&uart2_pins_a>;
++			status = "okay";
++		};
++
+ 		i2c0: i2c@01c2ac00 {
+ 			pinctrl-names = "default";
+ 			pinctrl-0 = <&i2c0_pins_a>;
+@@ -264,6 +284,22 @@
+ 		enable-active-high;
+ 		gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>;
+ 	};
++
++	rfkill-switches {
++		compatible = "simple-bus";
++		pinctrl-names = "default";
++
++		rfkill_bt {
++			compatible = "rfkill-gpio";
++			pinctrl-0 = <&bt_pwr_pin>, <&clk_out_a_pins_a>;
++			rfkill-name = "bt";
++			rfkill-type = <2>;
++			bt_shutdown-gpios = <0>, <&pio 7 18 0>; /* PH18 */
++			bt_reset-gpios = <&pio 7 24 0>; /* PH24 */
++			clocks = <&clk_out_a>;
++			clock-frequency = <32768>;
++		};
++	};
+ };
+ 
+ #include "axp209.dtsi"
-- 
cgit v1.2.3