From 716ca530e1c4515d8683c9d5be3d56b301758b66 Mon Sep 17 00:00:00 2001 From: James <> Date: Wed, 4 Nov 2015 11:49:21 +0000 Subject: trunk-47381 --- .../patches-3.18/301-dt-sun7i-add-bananapro.patch | 291 +++++++++++++++++++++ 1 file changed, 291 insertions(+) create mode 100644 target/linux/sunxi/patches-3.18/301-dt-sun7i-add-bananapro.patch (limited to 'target/linux/sunxi/patches-3.18/301-dt-sun7i-add-bananapro.patch') diff --git a/target/linux/sunxi/patches-3.18/301-dt-sun7i-add-bananapro.patch b/target/linux/sunxi/patches-3.18/301-dt-sun7i-add-bananapro.patch new file mode 100644 index 0000000..c8cdb1d --- /dev/null +++ b/target/linux/sunxi/patches-3.18/301-dt-sun7i-add-bananapro.patch @@ -0,0 +1,291 @@ +From 3613d535a77270eaf15a5f988a48434c7d1530f2 Mon Sep 17 00:00:00 2001 +From: Hans de Goede +Date: Wed, 7 Jan 2015 20:44:52 +0100 +Subject: [PATCH] ARM: dts: sun7i: Add dts file for Bananapro board + +Add support for the new Bananapro A20 development board from lemaker.org. +This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for +OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, +3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi. + +Signed-off-by: Hans de Goede +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/sun7i-a20-bananapro.dts | 261 ++++++++++++++++++++++++++++++ + 2 files changed, 262 insertions(+) + create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapro.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -436,6 +436,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ + sun6i-a31-m9.dtb + dtb-$(CONFIG_MACH_SUN7I) += \ + sun7i-a20-bananapi.dtb \ ++ sun7i-a20-bananapro.dtb \ + sun7i-a20-cubieboard2.dtb \ + sun7i-a20-cubietruck.dtb \ + sun7i-a20-hummingbird.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts +@@ -0,0 +1,261 @@ ++/* ++ * Copyright 2015 Hans de Goede ++ * ++ * This file is dual-licensed: you can use it either under the terms ++ * of the GPL or the X11 license, at your option. Note that this dual ++ * licensing only applies to this file, and not this project as a ++ * whole. ++ * ++ * a) This file is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of the ++ * License, or (at your option) any later version. ++ * ++ * This file is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public ++ * License along with this file; if not, write to the Free ++ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, ++ * MA 02110-1301 USA ++ * ++ * Or, alternatively, ++ * ++ * b) Permission is hereby granted, free of charge, to any person ++ * obtaining a copy of this software and associated documentation ++ * files (the "Software"), to deal in the Software without ++ * restriction, including without limitation the rights to use, ++ * copy, modify, merge, publish, distribute, sublicense, and/or ++ * sell copies of the Software, and to permit persons to whom the ++ * Software is furnished to do so, subject to the following ++ * conditions: ++ * ++ * The above copyright notice and this permission notice shall be ++ * included in all copies or substantial portions of the Software. ++ * ++ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES ++ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND ++ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT ++ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, ++ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING ++ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR ++ * OTHER DEALINGS IN THE SOFTWARE. ++ */ ++ ++/dts-v1/; ++/include/ "sun7i-a20.dtsi" ++/include/ "sunxi-common-regulators.dtsi" ++ ++/ { ++ model = "LeMaker Banana Pro"; ++ compatible = "lemaker,bananapro", "allwinner,sun7i-a20"; ++ ++ soc@01c00000 { ++ spi0: spi@01c05000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins_a>; ++ status = "okay"; ++ }; ++ ++ mmc0: mmc@01c0f000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; ++ vmmc-supply = <®_vcc3v3>; ++ bus-width = <4>; ++ cd-gpios = <&pio 7 10 0>; /* PH10 */ ++ cd-inverted; ++ status = "okay"; ++ }; ++ ++ mmc3: mmc@01c12000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mmc3_pins_a>; ++ vmmc-supply = <®_vmmc3>; ++ bus-width = <4>; ++ non-removable; ++ status = "okay"; ++ }; ++ ++ usbphy: phy@01c13400 { ++ usb1_vbus-supply = <®_usb1_vbus>; ++ usb2_vbus-supply = <®_usb2_vbus>; ++ status = "okay"; ++ }; ++ ++ ehci0: usb@01c14000 { ++ status = "okay"; ++ }; ++ ++ ohci0: usb@01c14400 { ++ status = "okay"; ++ }; ++ ++ ahci: sata@01c18000 { ++ status = "okay"; ++ }; ++ ++ ehci1: usb@01c1c000 { ++ status = "okay"; ++ }; ++ ++ ohci1: usb@01c1c400 { ++ status = "okay"; ++ }; ++ ++ pinctrl@01c20800 { ++ usb1_vbus_pin_bananapro: usb1_vbus_pin@0 { ++ allwinner,pins = "PH0"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; ++ ++ usb2_vbus_pin_bananapro: usb2_vbus_pin@0 { ++ allwinner,pins = "PH1"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; ++ ++ mmc0_cd_pin_bananapi: mmc0_cd_pin@0 { ++ allwinner,pins = "PH10"; ++ allwinner,function = "gpio_in"; ++ allwinner,drive = <0>; ++ allwinner,pull = <1>; ++ }; ++ ++ vmmc3_pin_bananapro: vmmc3_pin@0 { ++ allwinner,pins = "PH22"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; ++ ++ gmac_power_pin_bananapi: gmac_power_pin@0 { ++ allwinner,pins = "PH23"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; ++ ++ led_pins_bananapi: led_pins@0 { ++ allwinner,pins = "PH24", "PG2"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; ++ }; ++ ++ ir0: ir@01c21800 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&ir0_pins_a>; ++ status = "okay"; ++ }; ++ ++ uart0: serial@01c28000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins_a>; ++ status = "okay"; ++ }; ++ ++ uart2: serial@01c28800 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart2_pins_a>; ++ status = "okay"; ++ }; ++ ++ uart7: serial@01c29c00 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart7_pins_a>; ++ status = "okay"; ++ }; ++ ++ i2c0: i2c@01c2ac00 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins_a>; ++ status = "okay"; ++ ++ axp209: pmic@34 { ++ compatible = "x-powers,axp209"; ++ reg = <0x34>; ++ interrupt-parent = <&nmi_intc>; ++ interrupts = <0 8>; ++ ++ interrupt-controller; ++ #interrupt-cells = <1>; ++ }; ++ }; ++ ++ i2c2: i2c@01c2b400 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c2_pins_a>; ++ status = "okay"; ++ }; ++ ++ gmac: ethernet@01c50000 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gmac_pins_rgmii_a>; ++ phy = <&phy1>; ++ phy-mode = "rgmii"; ++ phy-supply = <®_gmac_3v3>; ++ status = "okay"; ++ ++ phy1: ethernet-phy@1 { ++ reg = <1>; ++ }; ++ }; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&led_pins_bananapi>; ++ ++ green { ++ label = "bananapi:green:usr"; ++ gpios = <&pio 7 24 0>; ++ }; ++ blue { ++ label = "bananapi:blue:usr"; ++ gpios = <&pio 6 2 0>; ++ }; ++ }; ++ ++ reg_usb1_vbus: usb1-vbus { ++ pinctrl-0 = <&usb1_vbus_pin_bananapro>; ++ gpio = <&pio 7 0 0>; /* PH0 */ ++ status = "okay"; ++ }; ++ ++ reg_usb2_vbus: usb2-vbus { ++ pinctrl-0 = <&usb2_vbus_pin_bananapro>; ++ gpio = <&pio 7 1 0>; /* PH1 */ ++ status = "okay"; ++ }; ++ ++ reg_gmac_3v3: gmac-3v3 { ++ compatible = "regulator-fixed"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gmac_power_pin_bananapi>; ++ regulator-name = "gmac-3v3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ startup-delay-us = <100000>; ++ enable-active-high; ++ gpio = <&pio 7 23 0>; ++ }; ++ ++ reg_vmmc3: vmmc3 { ++ compatible = "regulator-fixed"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vmmc3_pin_bananapro>; ++ regulator-name = "vmmc3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ enable-active-high; ++ gpio = <&pio 7 22 0>; ++ }; ++}; -- cgit v1.2.3