From d9d14f267c54d1015ef292a97403b4cd623b9b76 Mon Sep 17 00:00:00 2001 From: Zoltan HERPAI Date: Fri, 21 Nov 2014 18:42:43 +0000 Subject: sunxi: add initial 3.18 support Signed-off-by: Zoltan HERPAI git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43337 3c298f89-4303-0410-b956-a3cf2f4a3e73 --- .../202-dt-sun7i-add-bluetooth-to-cubietruck.patch | 75 ++++++++++++++++++++++ 1 file changed, 75 insertions(+) create mode 100644 target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch (limited to 'target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch') diff --git a/target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch b/target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch new file mode 100644 index 0000000000..f819849448 --- /dev/null +++ b/target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch @@ -0,0 +1,75 @@ +From c6e2b7dad39a7887f935458d1c8de84db06243e1 Mon Sep 17 00:00:00 2001 +From: Chen-Yu Tsai +Date: Thu, 26 Dec 2013 17:15:47 +0800 +Subject: [PATCH] ARM: dts: sun7i: add bluetooth module to CubieTruck DTS + +The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The +Bluetooth part is a BCM20710 IC connected to UART2 in the A20 +SoC. The IC also takes a 32.768 KHz low power clock input, a power +enable signal and a wake signal via GPIO. + +The Bluetooth module supports out-of-band interrupt signaling via +GPIO, but this is not supported in this patch. +--- + arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 36 ++++++++++++++++++++++++++++++ + 1 file changed, 36 insertions(+) + +diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +index f9ab5d4..69d8c4c 100644 +--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts ++++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +@@ -103,6 +103,20 @@ + allwinner,drive = <0>; + allwinner,pull = <0>; + }; ++ ++ bt_pwr_pin: bt_pwr_pin@0 { ++ allwinner,pins = "PH18"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; ++ ++ bt_wake_pin: bt_wake_pin@0 { ++ allwinner,pins = "PH24"; ++ allwinner,function = "gpio_out"; ++ allwinner,drive = <0>; ++ allwinner,pull = <0>; ++ }; + }; + + pwm: pwm@01c20e00 { +@@ -123,6 +137,12 @@ + status = "okay"; + }; + ++ uart2: serial@01c28800 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart2_pins_a>; ++ status = "okay"; ++ }; ++ + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; +@@ -214,4 +234,20 @@ + enable-active-high; + gpio = <&pio 7 9 0>; + }; ++ ++ rfkill-switches { ++ compatible = "simple-bus"; ++ pinctrl-names = "default"; ++ ++ rfkill_bt { ++ compatible = "rfkill-gpio"; ++ pinctrl-0 = <&bt_pwr_pin>, <&clk_out_a_pins_a>; ++ rfkill-name = "bt"; ++ rfkill-type = <2>; ++ bt_shutdown-gpios = <0>, <&pio 7 18 0>; /* PH18 */ ++ bt_reset-gpios = <&pio 7 24 0>; /* PH24 */ ++ clocks = <&clk_out_a>; ++ clock-frequency = <32768>; ++ }; ++ }; + }; -- cgit v1.2.3