From 4a4f3f4a88c2edcdd8dcaa1982ade136aecf2ae2 Mon Sep 17 00:00:00 2001 From: Luka Perkov Date: Tue, 10 Sep 2013 22:26:36 +0000 Subject: imx6: backport ahci support Signed-off-by: Tim Harvey Signed-off-by: Luka Perkov git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37936 3c298f89-4303-0410-b956-a3cf2f4a3e73 --- ...mx-add-ahci-sata-support-on-imx-platforms.patch | 306 +++++++++++++++++++++ 1 file changed, 306 insertions(+) create mode 100644 target/linux/imx6/patches-3.10/0005-ahci_imx-add-ahci-sata-support-on-imx-platforms.patch (limited to 'target/linux/imx6/patches-3.10/0005-ahci_imx-add-ahci-sata-support-on-imx-platforms.patch') diff --git a/target/linux/imx6/patches-3.10/0005-ahci_imx-add-ahci-sata-support-on-imx-platforms.patch b/target/linux/imx6/patches-3.10/0005-ahci_imx-add-ahci-sata-support-on-imx-platforms.patch new file mode 100644 index 0000000000..1adb41d25f --- /dev/null +++ b/target/linux/imx6/patches-3.10/0005-ahci_imx-add-ahci-sata-support-on-imx-platforms.patch @@ -0,0 +1,306 @@ +From 9e54eae23bc9cca0d8a955018c35b1250e09a73a Mon Sep 17 00:00:00 2001 +From: Richard Zhu +Date: Wed, 24 Jul 2013 14:15:29 +0800 +Subject: [PATCH] ahci_imx: add ahci sata support on imx platforms + +imx6q contains one Synopsys AHCI SATA controller, But it can't share +ahci_platform driver with other controllers because there are some +misalignments of the generic AHCI controller - the bits definitions of +the HBA registers, the Vendor Specific registers, the AHCI PHY clock +and the AHCI signals adjustment window(GPR13 register). + + - CAP_SSS(bit20) of the HOST_CAP is writable, default value is '0', + should be configured to be '1' + + - bit0 (only one AHCI SATA port on imx6q) of the HOST_PORTS_IMPL + should be set to be '1'.(default 0) + + - One Vendor Specific register HOST_TIMER1MS(offset:0xe0) should be + configured regarding to the frequency of AHB bus clock. + + - Configurations of the AHCI PHY clock, and the signal parameters of + the GPR13 + +Setup its own ahci sata driver, contained the imx6q specific +initialized codes, re-use the generic ahci_platform driver, and keep +the generic ahci_platform driver clean as much as possible. + +tj: patch description reformatted + +Signed-off-by: Richard Zhu +Reviewed-by: Shawn Guo +Signed-off-by: Tejun Heo +--- + drivers/ata/Kconfig | 9 ++ + drivers/ata/Makefile | 1 + + drivers/ata/ahci_imx.c | 236 +++++++++++++++++++++++++++++++++++++++++++++++++ + 3 files changed, 246 insertions(+) + create mode 100644 drivers/ata/ahci_imx.c + +--- a/drivers/ata/Kconfig ++++ b/drivers/ata/Kconfig +@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM + + If unsure, say N. + ++config AHCI_IMX ++ tristate "Freescale i.MX AHCI SATA support" ++ depends on SATA_AHCI_PLATFORM ++ help ++ This option enables support for the Freescale i.MX SoC's ++ onboard AHCI SATA. ++ ++ If unsure, say N. ++ + config SATA_FSL + tristate "Freescale 3.0Gbps SATA support" + depends on FSL_SOC +--- a/drivers/ata/Makefile ++++ b/drivers/ata/Makefile +@@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X) += sata_inic + obj-$(CONFIG_SATA_SIL24) += sata_sil24.o + obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o + obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o ++obj-$(CONFIG_AHCI_IMX) += ahci_imx.o + + # SFF w/ custom DMA + obj-$(CONFIG_PDC_ADMA) += pdc_adma.o +--- /dev/null ++++ b/drivers/ata/ahci_imx.c +@@ -0,0 +1,236 @@ ++/* ++ * Freescale IMX AHCI SATA platform driver ++ * Copyright 2013 Freescale Semiconductor, Inc. ++ * ++ * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms and conditions of the GNU General Public License, ++ * version 2, as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope it will be useful, but WITHOUT ++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or ++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for ++ * more details. ++ * ++ * You should have received a copy of the GNU General Public License along with ++ * this program. If not, see . ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include "ahci.h" ++ ++enum { ++ HOST_TIMER1MS = 0xe0, /* Timer 1-ms */ ++}; ++ ++struct imx_ahci_priv { ++ struct platform_device *ahci_pdev; ++ struct clk *sata_ref_clk; ++ struct clk *ahb_clk; ++ struct regmap *gpr; ++}; ++ ++static int imx6q_sata_init(struct device *dev, void __iomem *mmio) ++{ ++ int ret = 0; ++ unsigned int reg_val; ++ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent); ++ ++ imxpriv->gpr = ++ syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr"); ++ if (IS_ERR(imxpriv->gpr)) { ++ dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n"); ++ return PTR_ERR(imxpriv->gpr); ++ } ++ ++ ret = clk_prepare_enable(imxpriv->sata_ref_clk); ++ if (ret < 0) { ++ dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret); ++ return ret; ++ } ++ ++ /* ++ * set PHY Paremeters, two steps to configure the GPR13, ++ * one write for rest of parameters, mask of first write ++ * is 0x07fffffd, and the other one write for setting ++ * the mpll_clk_en. ++ */ ++ regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK ++ | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK ++ | IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK ++ | IMX6Q_GPR13_SATA_SPD_MODE_MASK ++ | IMX6Q_GPR13_SATA_MPLL_SS_EN ++ | IMX6Q_GPR13_SATA_TX_ATTEN_MASK ++ | IMX6Q_GPR13_SATA_TX_BOOST_MASK ++ | IMX6Q_GPR13_SATA_TX_LVL_MASK ++ | IMX6Q_GPR13_SATA_TX_EDGE_RATE ++ , IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB ++ | IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M ++ | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F ++ | IMX6Q_GPR13_SATA_SPD_MODE_3P0G ++ | IMX6Q_GPR13_SATA_MPLL_SS_EN ++ | IMX6Q_GPR13_SATA_TX_ATTEN_9_16 ++ | IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB ++ | IMX6Q_GPR13_SATA_TX_LVL_1_025_V); ++ regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN, ++ IMX6Q_GPR13_SATA_MPLL_CLK_EN); ++ usleep_range(100, 200); ++ ++ /* ++ * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL, ++ * and IP vendor specific register HOST_TIMER1MS. ++ * Configure CAP_SSS (support stagered spin up). ++ * Implement the port0. ++ * Get the ahb clock rate, and configure the TIMER1MS register. ++ */ ++ reg_val = readl(mmio + HOST_CAP); ++ if (!(reg_val & HOST_CAP_SSS)) { ++ reg_val |= HOST_CAP_SSS; ++ writel(reg_val, mmio + HOST_CAP); ++ } ++ reg_val = readl(mmio + HOST_PORTS_IMPL); ++ if (!(reg_val & 0x1)) { ++ reg_val |= 0x1; ++ writel(reg_val, mmio + HOST_PORTS_IMPL); ++ } ++ ++ reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000; ++ writel(reg_val, mmio + HOST_TIMER1MS); ++ ++ return 0; ++} ++ ++static void imx6q_sata_exit(struct device *dev) ++{ ++ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent); ++ ++ regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN, ++ !IMX6Q_GPR13_SATA_MPLL_CLK_EN); ++ clk_disable_unprepare(imxpriv->sata_ref_clk); ++} ++ ++static struct ahci_platform_data imx6q_sata_pdata = { ++ .init = imx6q_sata_init, ++ .exit = imx6q_sata_exit, ++}; ++ ++static const struct of_device_id imx_ahci_of_match[] = { ++ { .compatible = "fsl,imx6q-ahci", .data = &imx6q_sata_pdata}, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, imx_ahci_of_match); ++ ++static int imx_ahci_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct resource *mem, *irq, res[2]; ++ const struct of_device_id *of_id; ++ const struct ahci_platform_data *pdata = NULL; ++ struct imx_ahci_priv *imxpriv; ++ struct device *ahci_dev; ++ struct platform_device *ahci_pdev; ++ int ret; ++ ++ imxpriv = devm_kzalloc(dev, sizeof(*imxpriv), GFP_KERNEL); ++ if (!imxpriv) { ++ dev_err(dev, "can't alloc ahci_host_priv\n"); ++ return -ENOMEM; ++ } ++ ++ ahci_pdev = platform_device_alloc("ahci", -1); ++ if (!ahci_pdev) ++ return -ENODEV; ++ ++ ahci_dev = &ahci_pdev->dev; ++ ahci_dev->parent = dev; ++ ++ imxpriv->ahb_clk = devm_clk_get(dev, "ahb"); ++ if (IS_ERR(imxpriv->ahb_clk)) { ++ dev_err(dev, "can't get ahb clock.\n"); ++ ret = PTR_ERR(imxpriv->ahb_clk); ++ goto err_out; ++ } ++ ++ imxpriv->sata_ref_clk = devm_clk_get(dev, "sata_ref"); ++ if (IS_ERR(imxpriv->sata_ref_clk)) { ++ dev_err(dev, "can't get sata_ref clock.\n"); ++ ret = PTR_ERR(imxpriv->sata_ref_clk); ++ goto err_out; ++ } ++ ++ imxpriv->ahci_pdev = ahci_pdev; ++ platform_set_drvdata(pdev, imxpriv); ++ ++ of_id = of_match_device(imx_ahci_of_match, dev); ++ if (of_id) { ++ pdata = of_id->data; ++ } else { ++ ret = -EINVAL; ++ goto err_out; ++ } ++ ++ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); ++ if (!mem || !irq) { ++ dev_err(dev, "no mmio/irq resource\n"); ++ ret = -ENOMEM; ++ goto err_out; ++ } ++ ++ res[0] = *mem; ++ res[1] = *irq; ++ ++ ahci_dev->coherent_dma_mask = DMA_BIT_MASK(32); ++ ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask; ++ ahci_dev->of_node = dev->of_node; ++ ++ ret = platform_device_add_resources(ahci_pdev, res, 2); ++ if (ret) ++ goto err_out; ++ ++ ret = platform_device_add_data(ahci_pdev, pdata, sizeof(*pdata)); ++ if (ret) ++ goto err_out; ++ ++ ret = platform_device_add(ahci_pdev); ++ if (ret) { ++err_out: ++ platform_device_put(ahci_pdev); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int imx_ahci_remove(struct platform_device *pdev) ++{ ++ struct imx_ahci_priv *imxpriv = platform_get_drvdata(pdev); ++ struct platform_device *ahci_pdev = imxpriv->ahci_pdev; ++ ++ platform_device_unregister(ahci_pdev); ++ return 0; ++} ++ ++static struct platform_driver imx_ahci_driver = { ++ .probe = imx_ahci_probe, ++ .remove = imx_ahci_remove, ++ .driver = { ++ .name = "ahci-imx", ++ .owner = THIS_MODULE, ++ .of_match_table = imx_ahci_of_match, ++ }, ++}; ++module_platform_driver(imx_ahci_driver); ++ ++MODULE_DESCRIPTION("Freescale i.MX AHCI SATA platform driver"); ++MODULE_AUTHOR("Richard Zhu "); ++MODULE_LICENSE("GPL"); ++MODULE_ALIAS("ahci:imx"); -- cgit v1.2.3