aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
...
* image: move netgear-image to top and rename to -dniJonas Gorski2015-09-041-11/+2
| | | | | | | | Use the same naming as netgear-chk. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46791 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: rename NETGEAR_ variables to their netgear namesJonas Gorski2015-09-041-11/+11
| | | | | | | | Netgear names them BOARD_ID and HW_ID, so we should do the same. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46790 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: build images and add sysupgrade support for AP148Jonas Gorski2015-09-042-3/+35
| | | | | | | | | Add full ubi and sysupgrade images for AP148 and add sysupgrade support for ipq806x to allow updating the current installation. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46789 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: clear IMAGES for devicesJonas Gorski2015-09-041-0/+1
| | | | | | | | | Ensure that IMAGE-less devices won't keep the IMAGES of any previous devices. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46788 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: wrap legacy image in uImageJonas Gorski2015-09-041-2/+2
| | | | | | | | | Wrap the zImage in a uImage header so we can easily boot it from legacy u-boots. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46787 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: rename "rootfs" to "ubi" on nandJonas Gorski2015-09-042-0/+26
| | | | | | | | OpenWrt expects the ubi paritition to be named "ubi", not "rootfs". Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46786 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: enable smem-parser for nand on AP148Jonas Gorski2015-09-046-8/+30
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46785 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: enable ubiblock supportJonas Gorski2015-09-042-2/+2
| | | | | | | | To allow squashfs on ubi, enable ubiblock support in the kernel. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46782 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar7: fix HIGHMEM_START (#20427)Felix Fietkau2015-09-022-0/+22
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46773 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.18 to 3.18.21Jonas Gorski2015-09-0219-78/+43
| | | | | | | | | Changelog: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21 Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46768 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix devicetree corruption with some boot loaders if the caches are ↵Felix Fietkau2015-09-021-0/+18
| | | | | | | | not ready at boot Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46766 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: bridge, multicast-to-unicast: fix echoes on STAFelix Fietkau2015-09-022-18/+28
| | | | | | | | | | | | | | | | | | | | | Currently, multicast packets from an STA are sent to any according multicast listener directly through the bridge multicast-to-unicast feature. Unfortunately, so far this includes the originating STA, too, resulting in multicast packets being echo'ed back to the originating STA if it itself is a multicast listener for that group. This behaviour breaks IPv6 duplicate address detection: An IPv6 Neighbor Solicitation for IPv6 Duplicate Address Detection is being echo'ed back, resulting in the host falsely detecting an address collision, which makes the node unable to claim an IPv6 address and use IPv6 in general. Mac80211 unfortunately only prevents the echoes for us for multicast frames. For the multicast frames cast to a unicast destination we'll need to take care of excluding the originator ourselves. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46765 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: remove dead EASY33016 image recipeJonas Gorski2015-08-301-35/+0
| | | | | | | | | | Support for lantiq_svip_be has been removed a while ago, so EASY33016 images weren't buildable anymore. Remove the recipes as well as gzip compressed kernel support, as EASY33016 was the last user of it. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46760 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: disable the openwrt commandline hackJonas Gorski2015-08-306-6/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46759 3c298f89-4303-0410-b956-a3cf2f4a3e73
* malta: disable the openwrt commandline hackJonas Gorski2015-08-301-1/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46758 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm63xx: disable the openwrt commandline hackJonas Gorski2015-08-302-2/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46757 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: disable the openwrt commandline hackJonas Gorski2015-08-302-2/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46756 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ath25: disable the openwrt commandline hackJonas Gorski2015-08-301-1/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46755 3c298f89-4303-0410-b956-a3cf2f4a3e73
* adm5120: disable the openwrt commandline hackJonas Gorski2015-08-301-1/+0
| | | | | | | | We don't make use of it, so no need to have it enabled. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46754 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm63xx: remove legacy led/button related patchesJonas Gorski2015-08-3084-451/+309
| | | | | | | | | We register all gpio buttons and leds through DT, so no need to keep fixes/additions for the platform data based bay. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46753 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm63xx: add Comtrend VR-3026e supportJonas Gorski2015-08-3010-1/+267
| | | | | | | | | | Add support for Comtrend VR-3026e v1. The device is almost identical to the Comtrend VR-3025un. Signed-off-by: Martin Tesar <tesarmar@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46752 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix Linksys E1200 V2 image filenameRafał Miłecki2015-08-291-1/+1
| | | | | | | | Drop unwanted suffix (copy & paste mistake). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46742 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: support sysupgrade with Netgear R7000 original firmwareRafał Miłecki2015-08-261-0/+1
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46732 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: add OpenWrt specific stuff for Netgear R7000Rafał Miłecki2015-08-268-2/+64
| | | | | | | | This adds DT things that couldn't be upstreamed yet. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46731 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: use pending Netgear R7000 patchRafał Miłecki2015-08-264-118/+256
| | | | | | | | It includes support for LEDs and buttons. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46730 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: use backported patches for UART0 and profilingRafał Miłecki2015-08-265-25/+17
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46729 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm63xx: fix WAP-5813n default network configJonas Gorski2015-08-261-1/+1
| | | | | | | | | | | /etc/uci-defaults/02_network had a typo, making it generate the wrong network config. Closes #20407. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46727 3c298f89-4303-0410-b956-a3cf2f4a3e73
* linux: fix off-by-one in handling in /proc/net/routeJonas Gorski2015-08-261-0/+46
| | | | | | | | | | | | | Add an upstream fix for /proc/net/route causing missing routes doing several continued reads from it. Only 4.1+ is affected. Closes #20403. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46726 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm63xx: enable dual rx/tx spi support for hsspiJonas Gorski2015-08-253-4/+74
| | | | | | | | | | should improve flash access times. Should be harmless to gnerally enable regardless if a flash supporting dual reads is attached. In doubt, spi-nor will just fall back to serial reads. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46725 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: bridge, multicast-to-unicast: assign src after pskb_may_pull()Felix Fietkau2015-08-252-37/+56
| | | | | | | | | | A call to pskb_may_pull() might reallocate skb->data. Therefore we should only assign the src-pointer after any potential reallocations. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46721 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Revert "kernel: disable multicast-to-unicast translation for ipv6 neighbor ↵Felix Fietkau2015-08-252-40/+34
| | | | | | | | | | | | | | | | | | | | solicitation (#17625)" This reverts commit a080e8e1943156168913d0353a2e99d1151102aa. It did not fix the problem but just hid some symptom. The real issue was that IGMP/MLD report suppression was not considered for the multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD reports between STAs by utilizing AP-isolation and bridge-hairpinning should have fixed this. It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor Solicitations, too (once that feature is configured correctly). Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46720 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: remove already upstream applied patchJonas Gorski2015-08-231-73/+0
| | | | | | | | | | | | | | | | Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied in 4.1.6. This fixes the following build error: arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int' arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int' arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed Reported-by: swalker Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46715 3c298f89-4303-0410-b956-a3cf2f4a3e73
* adm5120: make patches apply againJonas Gorski2015-08-232-17/+17
| | | | | | | | Fix patches not applying anymore since r46654. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46714 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 4.1 to 4.1.6Jonas Gorski2015-08-2310-166/+41
| | | | | | | | | Changelog: * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.6 Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46713 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: kirkwood: fix ehci-orion probe if generic-phy isn't enabledJonas Gorski2015-08-233-0/+105
| | | | | | | | | Properly treat -ENOSYS as no PHY, else ehci-orion won't work without generic phy support. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46711 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm63xx: ensure dummy byte is set for mapped spi flash with fast readJonas Gorski2015-08-2318-78/+120
| | | | | | | | | | | | | Some CFEs seem to misconfigure the mapped memory flash access with fast read but without a dummy byte, causing all accesses to be prefixed with 0xff. This of course breaks reading out the nvram, so do not just move back to single i/o accessors, but also ensure that the dummy byte is correctly set. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46707 3c298f89-4303-0410-b956-a3cf2f4a3e73
* sunxi: bump to 4.1Zoltan HERPAI2015-08-211-1/+3
| | | | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46705 3c298f89-4303-0410-b956-a3cf2f4a3e73
* sunxi: add audio module for 4.1 Zoltan HERPAI2015-08-211-0/+17
| | | | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46704 3c298f89-4303-0410-b956-a3cf2f4a3e73
* sunxi: update ahci package list for a couple board profilesZoltan HERPAI2015-08-218-9/+16
| | | | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46703 3c298f89-4303-0410-b956-a3cf2f4a3e73
* sunxi: reorganize kmod-ata-sunxi dependenciesZoltan HERPAI2015-08-211-4/+2
| | | | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46702 3c298f89-4303-0410-b956-a3cf2f4a3e73
* This had been set in r44508 as a workaround for switchImre Kaloz2015-08-211-2/+1
| | | | | | | | | | | | | | | | problems. Now that the switch driver can handle two devices with the same MAC address in separate VLANs we can go back to using the same address on both interfaces. This is the Linksys firmware's default behavior. Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46700 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Previously, all VLANs (port-based or 802.1q) were sharingImre Kaloz2015-08-212-4/+19
| | | | | | | | | | | | | | | | | | | a single database in the ATU. This created problems in the case of a system where two ports/devices share a MAC address (e.g. Linksys WRT1900AC eth0/eth1). This also clears any bootloader-set FDB defaults. This had caused issues creating port-based VLANs when mappings overlapped previous VLANs. Packets destined to a port not in the default port group flooded all ports. Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC) Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46699 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: fix cobra chainmaskImre Kaloz2015-08-211-2/+2
| | | | | | | | | | Thanks Sebastian for spotting it. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46697 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: add missing symbols for 4.1Zoltan HERPAI2015-08-201-0/+3
| | | | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46696 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: add support for the Linksys boot counterImre Kaloz2015-08-192-14/+20
| | | | | | | | | | | | | | The u-boot boot counter was never reset after a successful boot, which sometimes could make some variables become out of sync. This patch adds support for the boot counter and enables auto_recovery unconditionally. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46690 3c298f89-4303-0410-b956-a3cf2f4a3e73
* at91: fix usb rate backport patch tab mangleJohn Crispin2015-08-171-14/+14
| | | | | | | | | The patch submitted in [46649] was mangled in the use of gmails webmail interface, tabs replaced with spaces, resulting in a patch which dit not apply. This should fix the issue, sorry for the noise. Signed-off-by: Ben Whitten <benwhitten@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46676 3c298f89-4303-0410-b956-a3cf2f4a3e73
* orion: remove IRQF_DISABLEDJohn Crispin2015-08-171-2/+2
| | | | | | | | | | no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46672 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: crypto: remove IRQF_DISABLEDJohn Crispin2015-08-173-3/+3
| | | | | | | | | | no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46671 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: Support newer versions of the PEF7071 ethernet PHYsJohn Crispin2015-08-172-2/+2
| | | | | | | | | | The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's PHY driver (for his u-boot sources) already supports that PHY because it uses a PHY ID mask of 0xfffffff8. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46670 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: remove support for kernel 3.18 and 4.0John Crispin2015-08-1728-1554/+0
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46668 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-09 21:14:50 +0000