aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: lzma-loader: fix O32 ABI conformanceGabor Juhos2016-03-211-0/+3
| | | | | | | | | | | | | | | | | | | According to the calling convention of the o32 ABI the caller function must reserve stack space for $a0-$a3 registers in case the callee needs to save its arguments. The assembly startup code does not reserve stack space for these registers thus when the main C function needs to save its arguments, that will cause a stack overflow. Fix the assembly code to reserve stack space for the registers to avoid that. Untested. It seems that the lzma-loader is not used at all? Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49062 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: MiWifi-Nano - change gpios to leds, add to default build groupJohn Crispin2016-03-203-23/+21
| | | | | | | | | | | | 1) Use leds to indicate: Red - Power Amber - Radio On Blue - Wifi associated 2) Add profile to default build group for MT7628 subtarget Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49045 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add support for Xiaomi MiWiFi NanoJohn Crispin2016-03-166-0/+126
| | | | | | | | | | | | | | | Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> v3 includes changes suggested by L. D. Pinney & Karl Palsson- Eliminate en25q64 (4MB) flash chip Alphabetization Remove hyphen in model Rename profile from miwifinano.mk to xiaomi.mk Add gpios that are attached to leds git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49024 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add support for GL-MT750John Crispin2016-03-107-1/+177
| | | | | | | | This patch adds support for GL-MT750. GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps. It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48994 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add support for GL-MT300NJohn Crispin2016-03-107-1/+173
| | | | | | | | This patch adds support for GL-MT300N. GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM, 2 LANs, USB, UART, GPIO and PoE support. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48993 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add support for GL-MT300AJohn Crispin2016-03-107-0/+190
| | | | | | | | This patches adds support for GL-MT300A. GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM, Two LANs, USB, UART and MMC daughter board. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48992 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add support for Planex MZK-WDPR.John Crispin2016-03-085-0/+84
| | | | | | | | | | | add support for Planex MZK-WDPR. MZK-WDPR(MZK-WDPR-R01) is internet radio tuner. This patch is "network board" in MZK-WDPR. LCD board is non OpenWrt Platform. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48968 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: convert the remaining subtargets to 4.4Felix Fietkau2016-03-0789-35482/+65
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48954 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix subtarget kernel version assignment (only mt7621 is ready for now)Felix Fietkau2016-03-072-1/+3
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48953 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add linux 4.4 support, update mt7621 subtarget to 4.4Felix Fietkau2016-03-0769-13/+30076
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48951 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: mt7621: fix WF-2881 for ubi splitJohn Crispin2016-03-042-14/+5
| | | | | | | | This patch fix firmware split for WF-2881 which was previously manually partitioned. Signed-off-by: YounJae Rho <luxflow@live.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48908 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add profiles for JCG routersJohn Crispin2016-03-042-0/+60
| | | | | | | | | | This patch adds profiles and support for building factory and sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R. Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48906 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add JCG routers to base-filesJohn Crispin2016-03-044-0/+18
| | | | | | | | | | This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to various scripts in the base-files directory. Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48905 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add device tree for JCG JHR-N926RJohn Crispin2016-03-041-0/+127
| | | | | | | | | | | | | | | | Add a device tree for JCG JHR-N825R This router is based on a RT3052 and has 4MB of CFI flash and 32MB of SDRAM. As a special feature, it comes with a two digit seven segment display that is connected to a pair of daisy-chained 74164 shift registers that can be controlled via GPIOs. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48904 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add device tree for JCG JHR-N825RJohn Crispin2016-03-041-0/+81
| | | | | | | | | | | | Add a device tree for JCG JHR-N825R This router is based on a RT3052 and has 4MB of CFI flash and 32MB of SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48903 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add device tree for JCG JHR-N805RJohn Crispin2016-03-041-0/+89
| | | | | | | | | | | | Add a device tree for JCG JHR-N805R This router is based on a RT3050 and has 4MB of SPI flash and 16MB of SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48902 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Incorrect file mode changeJohn Crispin2016-03-034-0/+0
| | | | | | | | | | | Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026") incorrectly changed the mode of the ramips shell scripts from 755 to 644. I.e., they are not excutable any more and for example devices will be left with broken configs. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48893 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: enable mt76 on mt7688 by defaultFelix Fietkau2016-03-022-0/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48886 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Added support for ZBT-826 / ZBT-1026John Crispin2016-03-017-0/+155
| | | | | | | | | Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826 Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996 Signed-off-by: Jamie Stuart <jamie@onebillion.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48865 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add sysupgrade support for mt7628Felix Fietkau2016-02-281-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48813 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: create device tree node for MT7628 WMAC in preparation for future ↵Felix Fietkau2016-02-282-0/+17
| | | | | | | | work on driver support in mt76 Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48812 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix GPIO names for RT5350F-OLinuXino-EVBJohn Crispin2016-02-261-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hi, the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14 as relay2 and relay1 respectively, as you can see from their rt5350f branch on GitHub. For some reason in the official stable build both the GPIOs are swapped and the wrong names are declared in the gpio-export directive. I'm submitting this patch which should roll back the wrong changes, so that we get backward compatibility with any script developed on RC3 which controls the relays. After patching correct operation is restored: root@OpenWrt:/# cat /sys/kernel/debug/gpio GPIOs 0-21, platform/10000600.gpio, 10000600.gpio: gpio-0 (button ) in hi gpio-12 (relay2 ) out lo gpio-14 (relay1 ) out lo Thank you, Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48796 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: mt7620: fix failsafe switch configJohn Crispin2016-02-251-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | As indicated in the bug tracker[1], failsafe mode is broken on at least some devices using the mt7620 switch (and possibly mt7621). The thread explicitly mentions the Xiaomi MiWifi, and the Nexx WT3020, and an unspecified device using the mt7621 switch; the issue also applies to the Netgear EX2700. The problem is that failsafe mode uses eth0, but enable_vlan is always set to 1 by the switch driver. Connecting to and/or pinging the device fails. This patch fixes the failsafe preinit config, by making sure that vlan support is disabled. It currently only fixes the switch config on mt7620, but might apply to the mt7621 as well, so the patch has been designed with this in mind. A similar (line wrapped) patch was submitted in December by Simon Peter, but never accepted and/or discussed. This patch applies to both Chaos Calmer and trunk. [1] https://dev.openwrt.org/ticket/18768 Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48772 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: build factory images for Netgear EX2700John Crispin2016-02-252-1/+27
| | | | | | | | | | | | | | | | This patch adds support for building factory and sysupgrade images for the Netgear EX2700 that don't require modification of u-boot environment variables. The bootloader on this device expects the kernel partition to end on a 64k block boundary. The last 64 byte of the kernel partition must contain a valid uImage header - in the stock firmware, this is the uImage header of the root filesystem. For this patch, we're using the uImage header of a 0 byte partition (ex2700-fakeroot.uImage). Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48771 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix WSR-1166 partition tableFelix Fietkau2016-02-221-2/+2
| | | | | | | | | - Fix typo in board_data partition start address - Increase board_data partition size in order to exploit all flash size Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48751 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ralink: fix mt7628 ehci supportJohn Crispin2016-02-192-7/+61
| | | | | | | | the u2_phy init was missing Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48747 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ralink: unbreak port4 on mt7620John Crispin2016-02-191-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48746 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add support for Phicomm PSG1208John Crispin2016-02-158-1/+142
| | | | | | | | | | This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram. The WPS led is uesd as status_led because the power light can't be controlled with GPIO. It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48721 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Support LEDs on D-Link DIR-860L B1John Crispin2016-02-121-0/+20
| | | | | | | | Adds the required gpio definitions. Signed-off-by: Johannes Wienke <languitar@semipol.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48715 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add support for Netgear EX2700John Crispin2016-02-128-1/+177
| | | | | | | | | | | | | | | | This patch adds support for the Netgear EX2700 and builds an approriate sysupgrade image. What's missing is the option to build a factory image flashable via the router's stock web interface, but this approach is hindered by the fact that u-boot operforms an additional integrity check, which expects a uImage header in the last 64 bytes of the "kernel" partition, which the bootloader expects to be 960k, a size exceeded by the standard OpenWrt kernel. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48698 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix build error on oversized images by putting the dir-860l-b1 size ↵Felix Fietkau2016-02-081-2/+2
| | | | | | | | check at the end of the chain Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48681 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: HLK-RM04 - Enable GPIO14 for WPS buttonJohn Crispin2016-02-084-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The top half of UARTF on the HLK-RM04 is used for GPIO. mode 1 mode 2 RIN GPIO14 DSR_N GPIO13 DCD_N GPIO12 DTR_N GPIO11 RXD GPIO10 CTS_N GPIO09 TXD GPIO08 RTS_N GPIO07 This patch applies 3'b101 mode to UARTF: GPIO14 GPIO13 GPIO12 GPIO11 RXD CTS_N TXD RTS_N Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi). This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file. Signed-off-by: John Clark <inindev@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48665 3c298f89-4303-0410-b956-a3cf2f4a3e73
* rampis: HLK-RM04 - Setup I2C as GPIOJohn Crispin2016-02-081-1/+20
| | | | | | | | | | | | | | | | | | | The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2. Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0 Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1 group mode 1 mode 2 hlk-rm04 pin & export i2c i2c_sd gpio1 (pin 8, hlk-rm04:gpio0) i2c i2c_sclk gpio2 (pin 9, hlk-rm04:gpio1) reference: http://www.hlktech.net/product_detail.php?ProId=39 http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf Signed-off-by: John Clark <inindev@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48664 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: HLK-RM04 - Fix push button functionsJohn Crispin2016-02-081-3/+7
| | | | | | | | | The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198 The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211 Signed-off-by: John Clark <inindev@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48663 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: HLK-RM04 - Remove power LED configJohn Crispin2016-02-081-9/+0
| | | | | | | | | The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it. (Note that GPIO0 is actually connected to the RESET button.) Signed-off-by: John Clark <inindev@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48662 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: add IMAGE_SIZE to DEVICE_VARS, it is used by build templatesFelix Fietkau2016-02-011-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48611 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: make tp-link firmware size errors non-fatalFelix Fietkau2016-01-281-6/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48526 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix image size checks for Buffalo WSR-1166 and WSR-600Felix Fietkau2016-01-261-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48508 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update kernel 4.3 to version 4.3.4Hauke Mehrtens2016-01-251-1/+1
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48498 3c298f89-4303-0410-b956-a3cf2f4a3e73
* base-files: remove default /etc/config/network, generate it via board.d insteadFelix Fietkau2016-01-251-5/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48493 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: re-enable highmem support for MT7621 now that it's fixedFelix Fietkau2016-01-242-0/+13
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48469 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix serial baudrate for final version of ZBT-WG2626 boardJohn Crispin2016-01-191-1/+1
| | | | | | | | | | The bootloader was updated and now uses 115200 instead of 57600 baud for the serial console. Change this also in OpenWrt's DTS, so the rate is consistent for bootloader and linux kernel output. Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48359 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: HiLink HLK-RM04 image name typo (RM02 -> RM04)John Crispin2016-01-191-1/+1
| | | | | | | | The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02" Signed-off-by: John Clark <inindev@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48355 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: delete the broken sound driverFelix Fietkau2016-01-182-8488/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48318 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: mark kmod-sound-mtk as broken, it does not compile properlyFelix Fietkau2016-01-181-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48317 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix kernel config handling for mt7620/mt7628 sound moduleFelix Fietkau2016-01-181-4/+35
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48316 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel/4.3: update to version 4.3.3Hauke Mehrtens2016-01-125-31/+20
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48224 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: do not rely on $(BIN_DIR) installed files during image build (for ↵Felix Fietkau2016-01-061-3/+3
| | | | | | | | ubnt-erx) Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48147 3c298f89-4303-0410-b956-a3cf2f4a3e73
* targets: add kernel image dependencies on device tree filesFelix Fietkau2016-01-061-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48146 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: do not attempt to build ubnt-erx initramfs image if initramfs ↵Felix Fietkau2016-01-061-1/+1
| | | | | | | | support is disabled Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@48144 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 15:28:11 +0000