| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
| |
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44063 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43734 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
pointer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43588 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Similar to patch 2. Replace further mdelay calls.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43540 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43539 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43538 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43401 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43385 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43382 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43307 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Sets the system LED on the EasyLink M150 and mini to lower-case "easylink"
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43271 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43265 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43258 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Michaël Burtin <mburtin@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43173 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43026 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42922 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42897 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42782 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42552 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
completed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42457 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42432 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
(#13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42429 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42428 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
(improves performance) (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42427 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
tx hangs in some setups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42333 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.
Fixes #13072
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42328 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42280 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42193 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42184 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42130 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
Signed-off-by: Zhao, Gang <gang.zhao.42@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42038 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41993 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41932 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41814 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
LED script expects WLAN LED to be "gl-connect:red:wlan".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41793 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41788 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41769 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41658 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41649 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41643 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5714/
[juhosg:
- drop nvram.c modifications,
- create a separate kernel patch,
- use ath79_setup_qca955x_eth_cfg helper,
- merge esr900_{010,common}_setup functions,
- statically init AR8327 pad configurations,
- use pr_err instead of printk]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41640 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41627 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
[juhosg:
- fix coding style in mach-esr1750.c,
- rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41624 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5839/
[juhosg: fix coding style]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41623 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41622 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41618 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
New router/repeater from TP-LINK
- CPU: Atheros AR9341-DL3A (AP123)
- Flash: 4MB
- Ram: 32MB
Similar to TL-WA850RE.
Changes: rename file after r41596
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41598 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Corrected patch ath79 insted of auth79. Sorry.
Signed-off-by: Fredrik Jonson <fredrik@famjonson.se>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41596 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41450 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
sorry, the downside when applying patches with patch
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41350 3c298f89-4303-0410-b956-a3cf2f4a3e73
|