| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47883 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
This patch adds the rx/tx register offsets for the qca955x SoC.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47882 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47881 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47880 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
Add 'platform_nand_pre_upgrade' callback to allow platform specific
preparation right before flashinng, when already in ramdisk.
Example uses might be setting correct values for CI_{KERNPART,UBIPART}.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47879 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47878 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
this is what you get if you manually apply patches with c&p
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47877 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47876 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47875 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47874 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47873 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47872 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47871 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47870 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47869 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47868 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47867 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47866 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
mostly implicit defines due to missing includes plus one const that
shouldn't be one.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47865 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Add the info on exceeding bytes also to the remaining log messages.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47864 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47863 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47862 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47861 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
OpenSSL moves old versions of the library from
http://www.openssl.org/source/ to
http://www.openssl.org/source/old/$version/ breaking the old links.
That behavior breaks the OpenWRT-build every time OpenSSL releases
a new version.
This patch adds http://www.openssl.org/source/old/$version/ to the
PKG_SOURCE_URL of OpenSSL to avoid breaking the build whenever
OpenSSL releases a new version.
Signed-off-by: Kevin Kirsch <ranlvor@starletp9.de>
Reviewed-by: Alexander Dahl <post@lespocky.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47860 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47859 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
-fixed-time <timestamp> set mkfs-timestamp and file-mtime to this timestamp.
Reproducible builds requires the removal of all timestamp or setting all to a specific one.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47858 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Add the option "--all-servers" which forces dnsmasq to send all
queries to all servers and then take the first answer.
Signed-off-by: Andréas Gustafsson <gurgalof@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47857 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
This patch adds firmware generation tool for Cisco's MR18
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47856 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47855 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
LEDs which are controlled by a PWM need to use the supplied
max_brightness instead. Otherwise they might appear to be
very dim / broken.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47854 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Packages using libncursesw can fail to build if both libncurses and libncursesw
are not installed. Currently the ncurses.h file is installed in "usr/include/ncursesw"
directory and includes other .h files in the "usr/include" directory incorrectly.
For example: Including <ncursesw/ncurses.h> fails due to these references. These build
changes will set the correct include paths within the developer includes.
Packages that expect ncurses.h (or curses.h) in the default "usr/include" path fail
even when expecting to build with libncursesw and will need to be fixed as well. However,
they cannot be fixed until this patch is applied.
Signed-off-by: Ted Hess <thess@kitschensync.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47853 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Useful when using sound players that can send to icecast, etc. without any sound device attached.
Signed-off-by: Ted Hess <thess@kitschensync.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47852 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47851 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.
This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.
This results for a BTHOMEHUBV5A into the following led configuration:
- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"
With the final result of a switched off power led after boot.
The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47850 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47849 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47848 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
This patch is for Wallys DR344 support under OpenWRT
Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47847 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Build image for the AP121 reference board with 16MB flash.
Signed-off-by: Norbert Wegener <nw@wegener-net.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47846 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47845 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47844 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47843 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47842 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This resolves compilation warnings like this:
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_probe':
drivers/gpio/gpio-mt7621.c:328:46: warning: passing argument 2 of 'irq_set_chained_handler' from incompatible pointer type [-Wincompatible-pointer-types]
irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler);
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47841 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Update CM_GCR_CPC_BASE_CPCBASE_{MSK,SHF} to match datasheet
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47840 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
All gic patch was doing is removing code added by mt7621 support patch.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47839 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
accessed properly
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47838 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
CPUs in CPS mode
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47837 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
This also adds dts nodes for cpc and mc for documentation purposes
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47836 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47835 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47834 3c298f89-4303-0410-b956-a3cf2f4a3e73
|