1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
|
From: Benjamin Berg <benjamin.berg@open-mesh.com>
Date: Mon, 4 Jul 2016 14:37:22 +0200
Subject: [PATCH] ath9k: Use tsf offset helper in ath9k_hw_reset
These changes make ath9k_hw_reset more consistent with other places that
handle the TSF value by using the same helper routine.
A slight improvement is to not assume that a fixed time of 1.5ms has
passed for the initval writes when compared to the first write attempt.
Instead the TSF value is re-calculated which will yield a higher accuracy
of the restored TSF timer.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
---
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -1832,8 +1832,9 @@ int ath9k_hw_reset(struct ath_hw *ah, st
u32 saveLedState;
u32 saveDefAntenna;
u32 macStaId1;
+ struct timespec tsf_ts;
+ u32 tsf_offset;
u64 tsf = 0;
- s64 usec = 0;
int r;
bool start_mci_reset = false;
bool save_fullsleep = ah->chip_fullsleep;
@@ -1877,8 +1878,8 @@ int ath9k_hw_reset(struct ath_hw *ah, st
macStaId1 = REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_BASE_RATE_11B;
/* Save TSF before chip reset, a cold reset clears it */
+ getrawmonotonic(&tsf_ts);
tsf = ath9k_hw_gettsf64(ah);
- usec = ktime_to_us(ktime_get_raw());
saveLedState = REG_READ(ah, AR_CFG_LED) &
(AR_CFG_LED_ASSOC_CTL | AR_CFG_LED_MODE_SEL |
@@ -1911,8 +1912,8 @@ int ath9k_hw_reset(struct ath_hw *ah, st
}
/* Restore TSF */
- usec = ktime_to_us(ktime_get_raw()) - usec;
- ath9k_hw_settsf64(ah, tsf + usec);
+ tsf_offset = ath9k_hw_get_tsf_offset(&tsf_ts, NULL);
+ ath9k_hw_settsf64(ah, tsf + tsf_offset);
if (AR_SREV_9280_20_OR_LATER(ah))
REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL, AR_GPIO_JTAG_DISABLE);
@@ -1932,12 +1933,11 @@ int ath9k_hw_reset(struct ath_hw *ah, st
/*
* Some AR91xx SoC devices frequently fail to accept TSF writes
* right after the chip reset. When that happens, write a new
- * value after the initvals have been applied, with an offset
- * based on measured time difference
+ * value after the initvals have been applied.
*/
if (AR_SREV_9100(ah) && (ath9k_hw_gettsf64(ah) < tsf)) {
- tsf += 1500;
- ath9k_hw_settsf64(ah, tsf);
+ tsf_offset = ath9k_hw_get_tsf_offset(&tsf_ts, NULL);
+ ath9k_hw_settsf64(ah, tsf + tsf_offset);
}
ath9k_hw_init_mfp(ah);
|
