Index: compat-wireless-2008-05-26/config.mk =================================================================== --- compat-wireless-2008-05-26.orig/config.mk 2008-05-27 19:15:19.000000000 +0100 +++ compat-wireless-2008-05-26/config.mk 2008-05-27 19:52:31.000000000 +0100 @@ -28,73 +28,6 @@ CONFIG_NL80211=y # PCI Drivers ifneq ($(CONFIG_PCI),) -CONFIG_ATH5K=m -CONFIG_ATH5K_DEBUG=n - -# Required for older kernels which still use this flag. -CONFIG_IWLWIFI=m - -CONFIG_IWLCORE=m -CONFIG_IWL3945=m -CONFIG_IWL4965=m -CONFIG_IWL4965_HT=y -CONFIG_B43=m -# B43 uses PCMCIA only for Compact Flash. The Cardbus cards uses PCI -# Example, bcm4318: -# http://www.multicap.biz/wireless-lan/indoor-wlan-hardware/sdc-cf10g-80211g-compact-flash-module -CONFIG_B43_PCMCIA=y -CONFIG_B43_DMA=y -CONFIG_B43_PIO=y -# B43_PIO selects SSB_BLOCKIO -CONFIG_SSB_BLOCKIO=y -CONFIG_B43_DMA_AND_PIO_MODE=y -CONFIG_B43_PCI_AUTOSELECT=y -CONFIG_B43_PCICORE_AUTOSELECT=y -#CONFIG_B43_RFKILL=n -CONFIG_B43_LEDS=y -# CONFIG_B43_DEBUG is not set - -CONFIG_B43LEGACY=m -CONFIG_B43LEGACY_PCI_AUTOSELECT=y -CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y -CONFIG_B43LEGACY_DMA=y -CONFIG_B43LEGACY_PIO=y -CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y - -# The Intel ipws -CONFIG_IPW2100=m -CONFIG_IPW2100_MONITOR=y -CONFIG_IPW2200=m -CONFIG_IPW2200_MONITOR=y -CONFIG_IPW2200_RADIOTAP=y -CONFIG_IPW2200_PROMISCUOUS=y -# The above enables use a second interface prefixed 'rtap'. -# Example usage: -# -# % modprobe ipw2200 rtap_iface=1 -# % ifconfig rtap0 up -# % tethereal -i rtap0 -# -# If you do not specify 'rtap_iface=1' as a module parameter then -# the rtap interface will not be created and you will need to turn -# it on via sysfs: -# -# % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface -CONFIG_IPW2200_QOS=y - -NEED_IEEE80211=y - -CONFIG_P54_PCI=m - -CONFIG_SSB_PCIHOST_POSSIBLE=y -CONFIG_SSB_PCIHOST=y -CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y -CONFIG_SSB_DRIVER_PCICORE=y -CONFIG_SSB_B43_PCI_BRIDGE=y - -CONFIG_RTL8180=m -CONFIG_ADM8211=m - CONFIG_RT2X00_LIB_PCI=m CONFIG_RT2400PCI=m CONFIG_RT2500PCI=m @@ -116,33 +49,6 @@ CONFIG_EEPROM_93CX6=m # USB Drivers ifneq ($(CONFIG_USB),) -CONFIG_ZD1211RW=m - -# support for USB Wireless devices using Atmel at76c503, -# at76c505 or at76c505a chips. -CONFIG_USB_ATMEL=m - -# Stuff here things which depend on kernel versions for USB -ifeq ($(shell test -e $(KLIB_BUILD)/Makefile && echo yes),yes) -KERNEL_SUBLEVEL = $(shell $(MAKE) -C $(KLIB_BUILD) kernelversion | sed -n 's/^2\.6\.\([0-9]\+\).*/\1/p') -ifeq ($(shell test $(KERNEL_SUBLEVEL) -gt 21 && echo yes),yes) - -# Sorry, rndis_wlan uses cancel_work_sync which is new and can't be done in compat... - -# Wireless RNDIS USB support (RTL8185 802.11g) A-Link WL54PC -# All of these devices are based on Broadcom 4320 chip which -# is only wireless RNDIS chip known to date. -# Note: this depends on CONFIG_USB_NET_RNDIS_HOST and CONFIG_USB_NET_CDCETHER -# it also requires new RNDIS_HOST and CDC_ETHER modules which we add -CONFIG_USB_NET_RNDIS_HOST=m -CONFIG_USB_NET_RNDIS_WLAN=m -CONFIG_USB_NET_CDCETHER=m - -endif -endif - -CONFIG_P54_USB=m -CONFIG_RTL8187=m # RT2500USB does not require firmware CONFIG_RT2500USB=m @@ -168,39 +74,6 @@ ifeq ($(NEED_RT2X00_FIRMWARE),y) CONFIG_RT2X00_LIB_FIRMWARE=y endif -# p54 -CONFIG_P54_COMMON=m - -# Sonics Silicon Backplane -CONFIG_SSB_POSSIBLE=y -CONFIG_SSB=m -CONFIG_SSB_SPROM=y - -ifneq ($(CONFIG_PCMCIA),) -CONFIG_SSB_PCMCIAHOST=y -endif - -# These two are for mips -CONFIG_SSB_DRIVER_MIPS=n -CONFIG_SSB_PCICORE_HOSTMODE=n -# CONFIG_SSB_DEBUG is not set -# CONFIG_SSB_DRIVER_EXTIF=y - -ifneq ($(CONFIG_USB),) -CONFIG_LIBERTAS_USB=m -NEED_LIBERTAS=y -endif -ifneq ($(CONFIG_PCMCIA),) -CONFIG_LIBERTAS_CS=m -NEED_LIBERTAS=y -endif -ifeq ($(NEED_LIBERTAS),y) -CONFIG_LIBERTAS=m -# Libertas uses the old stack but not fully, it will soon -# be cleaned. -NEED_IEEE80211=y -endif - ifeq ($(NEED_IEEE80211),y) # Old ieee80211 "stack" # Note: old softmac is scheduled for removal so we