| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
solicitation (#17625)"
This reverts commit a080e8e1943156168913d0353a2e99d1151102aa.
It did not fix the problem but just hid some symptom. The real issue was
that IGMP/MLD report suppression was not considered for the
multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD
reports between STAs by utilizing AP-isolation and bridge-hairpinning
should have fixed this.
It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor
Solicitations, too (once that feature is configured correctly).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46720
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied
in 4.1.6. This fixes the following build error:
arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here
arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here
scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed
Reported-by: swalker
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46715
|
|
|
|
|
|
|
|
| |
Fix patches not applying anymore since r46654.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46714
|
|
|
|
|
|
|
|
|
| |
Changelog:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.6
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46713
|
|
|
|
|
|
|
|
|
| |
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without
generic phy support.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46711
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some CFEs seem to misconfigure the mapped memory flash access with
fast read but without a dummy byte, causing all accesses to be prefixed
with 0xff.
This of course breaks reading out the nvram, so do not just move back to
single i/o accessors, but also ensure that the dummy byte is correctly
set.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46707
|
|
|
|
|
|
| |
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 46705
|
|
|
|
|
|
| |
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 46704
|
|
|
|
|
|
| |
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 46703
|
|
|
|
|
|
| |
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 46702
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Now that the switch driver can handle two devices with
the same MAC address in separate VLANs we can go back
to using the same address on both interfaces.
This is the Linksys firmware's default behavior.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46700
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
in the ATU. This created problems in the case of a system where two ports/devices share a MAC address (e.g. Linksys WRT1900AC eth0/eth1).
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46699
|
|
|
|
|
|
|
|
| |
Thanks Sebastian for spotting it.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46697
|
|
|
|
|
|
| |
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 46696
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The u-boot boot counter was never reset after a successful boot,
which sometimes could make some variables become out of sync.
This patch adds support for the boot counter and enables
auto_recovery unconditionally.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46690
|
|
|
|
|
|
|
|
|
| |
The patch submitted in [46649] was mangled in the use of gmails webmail interface, tabs replaced with spaces, resulting in a patch which dit not apply.
This should fix the issue, sorry for the noise.
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
SVN-Revision: 46676
|
|
|
|
|
|
|
|
|
|
| |
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46672
|
|
|
|
|
|
|
|
|
|
| |
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46671
|
|
|
|
|
|
|
|
|
|
| |
The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's
PHY driver (for his u-boot sources) already supports that PHY because
it uses a PHY ID mask of 0xfffffff8.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46670
|
|
|
|
|
|
| |
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 46668
|
|
|
|
|
|
|
|
| |
0073 needs to applied afert 0102
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46667
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Instead of using board name provided explicitly as text in LED name, ex.:
[...]
mlwg2)
status_led="mlwg2:blue:system"
[...]
use $board variable, which allows to combine together multiple boards with same color and LED names, ex:
[...]
mlw221|\
mlwg2)
status_led="$board:blue:system"
[...]
The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46665
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
* fixes wrong indentation
* keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
* fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
* combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46664
|
|
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
|
|
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds flash layout parser for TP-Link firmwares which have a 64kb
bootloader.
This is used for TP-Link TL-WDR6500 v2.
SVN-Revision: 46662
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46660
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46659
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
*Enable SMEM MTD parser and its dependencies (SMEM & HW spinlocks) in
the kernel config
*Replaces the MTD layout in DT by the dynamic layout provided by the
SMEM parser for AP148
Using the OF based parser is still possible on platforms which have a
fixed MTD partition layout.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46658
|
|
|
|
|
|
|
|
|
| |
This patch adds a new parser which uses the SMEM available on IPQ and
some other QCOM platforms to map the MTD partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46657
|
|
|
|
|
|
|
|
|
|
|
|
| |
2 patches are cherry-picked from the following LKML thread:
*https://lkml.org/lkml/2015/4/11/208
The last patch (036-soc-qcom-add-smem-to-IPQ806x-platforms.patch) is
adding the corresponding DT nodes required for IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46656
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This change cherry-picks the following 3 changes from linux-next:
*fb7737 hwspinlock/core: add device tree support
*19a0f6 hwspinlock: qcom: Add support for Qualcomm HW Mutex block
*bd5717 hwspinlock: qcom: Correct msb in regmap_field
We're also adding a patch to add the hardware spinlock device nodes on
IPQ806x platforms (033-soc-qcom-Add-sfbp-device-to-IPQ806x-dts.patch).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46655
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The "linux,part-probe" dts parsing is a pretty neat generic feature.
It has been posted to kernel.org and could easily be reused by all
targets.
This change moves the patch to the 3.18 and 4.1 generic folders, and
makes the feature available to all platforms who may want to use it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46654
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for the Black Swift board:
http://www.black-swift.com/
Took relevant parts and slightly adapted from:
https://github.com/blackswift/openwrt/blob/master/bsb.patch
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 46651
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch is backport of a fix to a USB prototype mismatch bug found
in 3.18 kernels, originally submitted by Boris Brezillon [1].
The symptom of this bug was that devices attached to the at91 using
at91_ohci on a hub never appeared and failed to initialise.
[1] http://www.spinics.net/lists/linux-usb/msg125969.html
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
SVN-Revision: 46649
|
|
|
|
|
|
|
|
|
| |
to avoid editing the dts every time the kernel size changes.
uImage is now bigger than 1MB. Pad uImage to 64k erase block size.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46648
|
|
|
|
|
|
|
|
|
|
| |
Switch to generich chip irqs/irq domains.
Interrupts were broken since kernel 3.14. dLAN USB extender is now
booting again.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46647
|
|
|
|
|
|
|
|
|
|
| |
Switch to new 8250 debug uart code because the old
mach-mcs814x/include/mach/debug-macro.S tries to include
asm/hardware/debug-8250.S which no longer exists since kernel 3.14
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46646
|
|
|
|
|
|
|
|
|
|
|
| |
The MT7621 uses a 2 bit wide configuration of the sdhci, spi, mdio, pcie,
wdt, uart2 and uart3 in the GPIO_MODE register. It was correctly done
for sdhci, spi, pcie and wdt, The same has to be done for uart3, uart2
and mdio.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46645
|
|
|
|
|
|
|
|
|
| |
The PINS conntrolled by the SPI bits in the GPIO_MODE register is always
7 and not 8 for nand mode.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46644
|
|
|
|
|
|
|
|
|
| |
The uart3 setting in GPIO_MODE register is before the uart2 setting. Also
don't mix uart2 and uart3 function/groups.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46643
|
|
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46642
|
|
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46641
|
|
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46640
|
|
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46639
|
|
|
|
|
|
| |
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 46637
|
|
|
|
|
|
| |
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 46636
|
|
|
|
|
|
|
|
| |
This device doesn't have defined LEDs in its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46635
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
base-files/etc/board.d/02_network
The following patch:
* fixes wrong indentation
* combines together boards with same configuration
* removes unnecessary spaces
* removes empty lines after ";;" and uses only "|\" (for consistency)
* orders boards alphabetically
in base-files/etc/board.d/02_network script.
One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs().
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46634
|
|
|
|
|
|
|
|
| |
Always use "|\" (without spaces) and keep boards in alphabetical order.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46633
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch:
* fixes various mistakes (leading spaces, wrong or missing model names)
* shortens model strings (we don't need to use whole model string from dts file, make it for consistency and as optimization)
* sorts boards alphabetically
in base-files/lib/ramips.sh script.
Case statement was tested after above changes with simple script, which:
* takes model string from dts{,i} file (model = "...")
* provides this value as case input ($machine)
* returns output ($name)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46632
|