summaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ralink: drop old ethernet driverJohn Crispin2015-12-1721-6842/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47899
* ralink: add reworked ethernet driverJohn Crispin2015-12-1717-24/+7877
| | | | | | | | update to the version of the driver that is on its way upstream Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47898
* ramips: add missing kernel symbolsJohn Crispin2015-12-126-0/+6
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47884
* ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)John Crispin2015-12-127-2/+301
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
* ramips: add support for Spansion S34ML0[24]G2 flashJohn Crispin2015-12-121-0/+43
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47880
* ralink: remove stray "+" from ethernet driverJohn Crispin2015-12-121-1/+1
| | | | | | | | this is what you get if you manually apply patches with c&p Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47877
* ramips: move partition definitions out of mt7621.dtsi fileJohn Crispin2015-12-122-20/+22
| | | | | | | | | Partitions defined in parent dtsi cannot be undefined in children. This moves partitions defined in mt7621.dtsi into board's device tree. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47876
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-123-0/+112
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47875
* Revert "ramips: use gic timer as clocksource for mt7621"Felix Fietkau2015-12-113-101/+0
| | | | | | This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7. SVN-Revision: 47872
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-112-2/+2
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* ramips: add additional support for MQmaker WiTi boardJohn Crispin2015-12-117-1/+178
| | | | | | | | | | | | | | The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna. This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 47845
* ramips: Fix support for PBR-M1 boardJohn Crispin2015-12-113-22/+61
| | | | | | | | | | The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it. The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds. Signed-off-by: 郭传鈜 <gch981213@gmail.com> SVN-Revision: 47844
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-113-0/+101
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47843
* ramips: enable CPS for mt7621John Crispin2015-12-113-123/+21
| | | | | | | | | | | | | Enables CPS multiprocessing instead ob obsoleted CMP for mt7621. This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx: * iperf shows only 50Mbits on direct gigabit connection to desktop, * ping times jump to 5-6ms to dorectly connected desktop * /proc/interrupts shows spurious interrups (ERR) Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47842
* ramips: irq handlers do not get irq in 4.3 kernel, update patchesJohn Crispin2015-12-112-29/+4
| | | | | | | | | | | This resolves compilation warnings like this: drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_probe': drivers/gpio/gpio-mt7621.c:328:46: warning: passing argument 2 of 'irq_set_chained_handler' from incompatible pointer type [-Wincompatible-pointer-types] irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler); Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47841
* ramips: Fix CM_GCR_CPC_BASE_CPCBASE_{MSK, SHF} valuesJohn Crispin2015-12-111-0/+13
| | | | | | | | Update CM_GCR_CPC_BASE_CPCBASE_{MSK,SHF} to match datasheet Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47840
* ramips: fold gic patch into mt7621 support patchJohn Crispin2015-12-112-571/+23
| | | | | | | | All gic patch was doing is removing code added by mt7621 support patch. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47839
* ramips: backport series of patches that ensure GCRs of other CPUs are ↵John Crispin2015-12-113-0/+269
| | | | | | | | accessed properly Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47838
* ramips: backport batch fixing illegal instruction when booting secodnary ↵John Crispin2015-12-111-0/+53
| | | | | | | | CPUs in CPS mode Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47837
* ramips: mt7621: use symbolic names of gic interrupt settingsJohn Crispin2015-12-1111-18/+30
| | | | | | | | This also adds dts nodes for cpc and mc for documentation purposes Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47836
* ralink: bump to the target to v4.3John Crispin2015-12-10104-5437/+3943
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47831
* build: fix arch used during dts compilationFelix Fietkau2015-12-101-1/+1
| | | | | | | | | Use kernel arch for dts compilation. Also use Image/BuildDTB to build dts for ramips. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47823
* all: remove dummy ucidef_set_interface_loopback() from board.dJo-Philipp Wich2015-12-031-2/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47744
* board.d: remove redundant ucidef_set_interfaces_lan_wan() callsJo-Philipp Wich2015-12-031-19/+0
| | | | | | | | | | This removes calls to ucidef_set_interfaces_lan_wan() and ucidef_set_interfaces_lan() on boards where all relevant info can be inferred from the switch definition. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47722
* board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()Jo-Philipp Wich2015-12-031-40/+20
| | | | | | | | | | | | This changes uci-defaults-new.sh, config_generate and all relevant board.d files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into a single function. Also removes now superfluous enable and reset arguments. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47721
* base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()Jo-Philipp Wich2015-12-031-2/+4
| | | | | | | | | | | | | | | Out of 69 switch definitions, only 3 pass something different than "1" as values for reset and enable, with one of those three being invalid. This change ... * removes the reset and enable arguments from ucidef_add_switch() * unconditionally writes reset:1 and enable:1 to JSON * converts the three users of nonstandard values to ucidef_add_switch_attr() Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47720
* ramips: switch ucidef_add_switch_vlan() to ucidef_add_switch_ports()Jo-Philipp Wich2015-12-031-38/+41
| | | | | | | | | | This migrates the final board.d user of ucidef_add_switch_vlan() to the new ucidef_add_switch_ports() approach, fixing some logic errors for a few boards along the way. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47717
* ramips: remove duplicate patchJohn Crispin2015-11-281-30/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47670
* ramips: adapt VoCore to new second spi device codeJohn Crispin2015-11-283-70/+66
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47667
* ramips: add second SPI clocksJohn Crispin2015-11-281-0/+30
| | | | | | | | These clocks were missing in the changes introduced in r47573-47580 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47666
* ramips: hg255d: replace ucidef_set_led_interface() with ucidef_set_led_netdev()Jo-Philipp Wich2015-11-261-1/+1
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47657
* ralink: renable nand supportJohn Crispin2015-11-241-0/+1
| | | | | | | | CONFIG_MTK_MTD_NAND was incorrectly disabled by r47619. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47640
* ramips: fix typo in image makefile (#18712)Felix Fietkau2015-11-241-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47627
* ralink: add support for netis WF-2881John Crispin2015-11-2410-4/+198
| | | | | | | | | | | | | | | | | | | | | | | | | netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN. It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. this device only works on top of UBI. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons (reset button) * ethernet switch and USB diag LEDs * UART * GPIOs * sysupgrade Tested and not working * failsafe Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 47619
* ramips: add support for Youku YK1John Crispin2015-11-246-2/+141
| | | | | | | | | Changes since V1: I resend this patch for current trunk.The former V1 patch is for CC branch. Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47617
* ramips: add second spi master sysclkJohn Crispin2015-11-241-0/+30
| | | | | | | | for mt7620, rt3883 and rt5350 Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47616
* ramips: update dtsi files to support second spi deviceJohn Crispin2015-11-227-380/+143
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47580
* ramips: use transfer_one instead of transfer_one_message on rt2880 spiJohn Crispin2015-11-221-65/+62
| | | | | | | | | | | | * use kernel buildin transfer_one_message. we only need to implement transfer_one and set_cs function * should support use gpio as cs pin * deselected the spi device when setup and add debug info * only reset device when first driver probe Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47579
* ramips: move rt2880 spi clock and reset init code to spi_prepare_messageJohn Crispin2015-11-221-68/+62
| | | | | | | | | | before spi transfer. use spi_prepare_message to setup spi hardware. it will setup MSB, spi mode and speed remove sys_freq member and speed check code Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47578
* ramips: improve rt2880 spi setupJohn Crispin2015-11-221-11/+62
| | | | | | | | | | * check clock rate, SPI mode, and word sizes * setup spi polarity * enable spi1 hw if need Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47577
* ramips: clean up rt2880 spi probe/removeJohn Crispin2015-11-221-25/+34
| | | | | | | | | | * fill struct according to the member order * add error clean up * set min/max spi speed. so we don't need to check again Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47576
* ramips: improve rt2880 spi wait ready functionJohn Crispin2015-11-221-16/+15
| | | | | | | | | | | use loops_per_jiffy, spi clock speed and write bytes to get the spi loop count. if loop to 0 than spi operation timeout. remove usleep. we only write 1 byte to spi device. use busy loop would be better. Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47575
* ramips: remove rt2880 spi lock and clean bit operationJohn Crispin2015-11-221-18/+5
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47574
* ramips: add rt2880/mt7620 spi register definesJohn Crispin2015-11-221-2/+63
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47573
* ralink: add missing nand layer hackJohn Crispin2015-11-211-0/+179
| | | | | | | | | | | | | | | | | It turned out that mtk_nand driver uses some sophisticated accounting and a general nand code must be patched. This patch adds required read and erase calls to a general nand code. I used a code for re6500 released by Linksys as a reference. All required operations (erase, write and read) are usable. However I found that jffs2 filesystem can be created only on top of a ubi volume. I tried to create jffs2 directly on mtd device but pages with clean markers are became uncorrectable. Signed-off-by: Kirill Berezin <fyiwdt@gmail.com> SVN-Revision: 47565
* ramips: init usb power for Lenovo Y1SJohn Crispin2015-11-211-0/+21
| | | | | | Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47557
* ramips: minor fixes for mt7621 profilesFelix Fietkau2015-11-072-4/+2
| | | | | | | | | * remove references to non-existing kmod-usb3-mt7621 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!) Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47407
* ramips: fix previous commitJohn Crispin2015-11-052-22/+66
| | | | | | | | r47388 accidentially changed 2 files too many Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47389
* ramips: minor tweak to the lks7688 baord nameJohn Crispin2015-11-054-68/+24
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47388
* ramips: add feature to blink led on sysupgradeJohn Crispin2015-11-032-1/+11
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47373
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 15:27:42 +0000