summaryrefslogtreecommitdiffstats
path: root/target/linux/ramips
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix typo in image makefile (#18712)Felix Fietkau2015-11-241-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47627
* ralink: add support for netis WF-2881John Crispin2015-11-2410-4/+198
| | | | | | | | | | | | | | | | | | | | | | | | | netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN. It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. this device only works on top of UBI. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons (reset button) * ethernet switch and USB diag LEDs * UART * GPIOs * sysupgrade Tested and not working * failsafe Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 47619
* ramips: add support for Youku YK1John Crispin2015-11-246-2/+141
| | | | | | | | | Changes since V1: I resend this patch for current trunk.The former V1 patch is for CC branch. Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47617
* ramips: add second spi master sysclkJohn Crispin2015-11-241-0/+30
| | | | | | | | for mt7620, rt3883 and rt5350 Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47616
* ramips: update dtsi files to support second spi deviceJohn Crispin2015-11-227-380/+143
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47580
* ramips: use transfer_one instead of transfer_one_message on rt2880 spiJohn Crispin2015-11-221-65/+62
| | | | | | | | | | | | * use kernel buildin transfer_one_message. we only need to implement transfer_one and set_cs function * should support use gpio as cs pin * deselected the spi device when setup and add debug info * only reset device when first driver probe Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47579
* ramips: move rt2880 spi clock and reset init code to spi_prepare_messageJohn Crispin2015-11-221-68/+62
| | | | | | | | | | before spi transfer. use spi_prepare_message to setup spi hardware. it will setup MSB, spi mode and speed remove sys_freq member and speed check code Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47578
* ramips: improve rt2880 spi setupJohn Crispin2015-11-221-11/+62
| | | | | | | | | | * check clock rate, SPI mode, and word sizes * setup spi polarity * enable spi1 hw if need Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47577
* ramips: clean up rt2880 spi probe/removeJohn Crispin2015-11-221-25/+34
| | | | | | | | | | * fill struct according to the member order * add error clean up * set min/max spi speed. so we don't need to check again Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47576
* ramips: improve rt2880 spi wait ready functionJohn Crispin2015-11-221-16/+15
| | | | | | | | | | | use loops_per_jiffy, spi clock speed and write bytes to get the spi loop count. if loop to 0 than spi operation timeout. remove usleep. we only write 1 byte to spi device. use busy loop would be better. Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47575
* ramips: remove rt2880 spi lock and clean bit operationJohn Crispin2015-11-221-18/+5
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47574
* ramips: add rt2880/mt7620 spi register definesJohn Crispin2015-11-221-2/+63
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47573
* ralink: add missing nand layer hackJohn Crispin2015-11-211-0/+179
| | | | | | | | | | | | | | | | | It turned out that mtk_nand driver uses some sophisticated accounting and a general nand code must be patched. This patch adds required read and erase calls to a general nand code. I used a code for re6500 released by Linksys as a reference. All required operations (erase, write and read) are usable. However I found that jffs2 filesystem can be created only on top of a ubi volume. I tried to create jffs2 directly on mtd device but pages with clean markers are became uncorrectable. Signed-off-by: Kirill Berezin <fyiwdt@gmail.com> SVN-Revision: 47565
* ramips: init usb power for Lenovo Y1SJohn Crispin2015-11-211-0/+21
| | | | | | Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47557
* ramips: minor fixes for mt7621 profilesFelix Fietkau2015-11-072-4/+2
| | | | | | | | | * remove references to non-existing kmod-usb3-mt7621 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!) Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47407
* ramips: fix previous commitJohn Crispin2015-11-052-22/+66
| | | | | | | | r47388 accidentially changed 2 files too many Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47389
* ramips: minor tweak to the lks7688 baord nameJohn Crispin2015-11-054-68/+24
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47388
* ramips: add feature to blink led on sysupgradeJohn Crispin2015-11-032-1/+11
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47373
* ramips: add support for ZBT WG2626John Crispin2015-11-027-3/+161
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47351
* ramips: add eeprom mtd partition to the Asus RP-N53 dtsJohn Crispin2015-11-021-0/+4
| | | | | | | | This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working. Signed-off-by: Alberto Mattea <alberto@mattea.info> SVN-Revision: 47350
* ramips: preinit: use iproute2 instead of vconfigJohn Crispin2015-11-021-2/+2
| | | | | | | | | | | | | | | Replace use of vconfig with the corresponding iproute2 syntax in /lib/preinit/07_set_preinit_iface_ramips The switch reset work-around needed on some ramips targets used the deprecated vconfig tool to bring up the pre-init/failsafe interface. This doesn't work on recent builds where vconfig is no longer being deployed, resulting in the device being unreachable when triggered into failsafe mode. Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47349
* ramips: add support for Dovado tiny ACJohn Crispin2015-11-028-0/+202
| | | | | | | | | | | | | | | | Add support for Dovado tiny AC wifi router. Soc: mt7620a ram: 64MB flash: 8MB 1x usb 2.0 two gigabit lan ports 5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip. Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47348
* ramips: add function to change rt2x00 wifi eeprom macJohn Crispin2015-11-021-0/+12
| | | | | | | | | Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom. Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump. Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47347
* ramips: mt7620 add icplus phy driver kernel config symbolJohn Crispin2015-11-021-0/+1
| | | | | | | | | Add missing icplus phy driver kernel config symbol to mt7620 subtarget. This is needed since some mt7620 devices have icplus ip1001 ethernet transceiver Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47346
* ramips: add support for the Asus RP-N53 in the "02_network" boot scriptJohn Crispin2015-11-021-1/+2
| | | | | | | | This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device. Signed-off-by: Alberto Mattea <alberto@mattea.info> SVN-Revision: 47345
* ramips: rt305x: enable seama mtdsplit parserJohn Crispin2015-11-021-0/+1
| | | | | | | | | D-Link DIR-610 A1 needs seama mtdsplit parser. This patch should fix #18046. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 47341
* ramips: rt305x: update kernel config symbolsJohn Crispin2015-11-021-3/+4
| | | | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 47340
* kernel: update kernel 3.18 to version 3.18.23Hauke Mehrtens2015-11-0114-101/+101
| | | | | | | | | | Changelog: * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.22 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.23 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 47334
* ramips: fix for kernel 4.0 napi repoll need return budgets numberFelix Fietkau2015-10-301-1/+4
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47306
* ramips: make the alsa driver register the codecJohn Crispin2015-10-261-38/+15
| | | | | | | | this allows using the codec even if it is not listed in the DTS Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47256
* ramips: gpio-mt7621 was not handling irqs above 31 properlyJohn Crispin2015-10-201-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47238
* ramips: add alsa supportJohn Crispin2015-10-195-1/+8554
| | | | | | | | | add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960. mt7620 is only compile tested. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47205
* ramips: add a baurate hackJohn Crispin2015-10-191-0/+12
| | | | | | | | | When talking to an atmel controller we need 9600 or 250000 baud. as 250000 does not exist we use 2500000. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47204
* ramips: add LinkIt Smart7688 supportJohn Crispin2015-10-198-0/+311
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47203
* ramips: fix /target/linux/ramips/dts/HC5XXX.dtsiJohn Crispin2015-10-071-2/+0
| | | | | | | | dtb complained about those lines Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47151
* ramips: enable mt76 by default for the mt7620 subtarget (for devices with ↵Felix Fietkau2015-10-062-3/+2
| | | | | | | | mt7620 + mt7612) Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47146
* ramips: improve read performance of the m25p80 chunked io patchFelix Fietkau2015-10-051-7/+58
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47137
* ramips: improve systick timerJohn Crispin2015-10-051-6/+145
| | | | | | | | | | | | when sleep mode is disable use MIPS as clocksource and clockevent instead of systick. because MIPS timer has higher resolution 5ns less than systick 20us and larger counter bits 32 > 16. clean interrupt by write compare register at isr. fix typo cause sleep mode not enable. Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47122
* ramips: fix use remove_irq to release irqaction resourceJohn Crispin2015-10-051-1/+1
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47121
* ramips: add support for 16MB VoCoreJohn Crispin2015-10-054-35/+93
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47120
* ramips: fix size-cells for spi nodesJohn Crispin2015-10-056-6/+6
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47119
* ramips: Ralink RT3883 RGMII pinmux fix.John Crispin2015-10-051-2/+2
| | | | | | | | | Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio. Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port. Signed-off-by: Nick Leiten <nickleiten@gmail.com> SVN-Revision: 47118
* ramips: Enable rx of 1536 bytes ethernet frames on MT7621John Crispin2015-10-051-4/+4
| | | | | | | | | | | The default switch frame size (with FCS + header) is 1536 bytes. But the GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to receive ethernet frames using the full of MTU 1500 + an extra VLAN header + VLAN header added by the switch. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47117
* ramips: Fix too small rx bufferJohn Crispin2015-10-051-4/+12
| | | | | | | | | | | | | | | | | | The driver assumes that the maximum received buffer for non-jumbo frames is 1536 bytes. But the allocation of the rx fragment doesn't reflect that. It currently allocates fragments which will only be large enough to be used as rx buffer with the size of 1534 bytes. This is problematic because the GMAC will now try to write to 2 bytes which don't belong to its receive buffer when a large enough ethernet frame is received. This may already be a problem on existing chips but will at least become a problem when the 1536 byte rx modus is enabled on MT7621a. It is required on this SoC to receive ethernet frames which use their full 1500 bytes MTU and a VLAN header next to the switch VLAN tag. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47116
* ramips: Fix setting of rx buffer lengthJohn Crispin2015-10-052-2/+3
| | | | | | | | | | | | | | The length of the DMA rx buffer was always set to 0 because the function for extracting the length was used to calculate the value for setting it. Instead the macro has to be split in a get and set function similar to the TX_DMA_(GET_|)PLEN(0|1) macro. No problem was noticed on MT7621a before this was changed and thus maybe it was hidden by different problem which is not yet fixed. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47115
* ramips: Allow to receive vlan over untag ports on MT7530John Crispin2015-10-051-3/+33
| | | | | | | | | | | | | | | | | | | | The MT7530 switch driver with enable_vlan set will automatically set all ports to the user port mode. The hardware will remove the incoming vlan tag on these ports and use it for its internal vlan. This is usually not wanted and makes it impossible to communicate via vlan over the switch in both directions. It is possible to configure a switch port to "transparent mode" when this port is only used as untag in the switch VLANs. This will disable the VLAN untagging of packets when they were received on this port. The tagging on "tag" ports based on the vlan id is still working. The transparent port mode cannot be used when a port is both used in a VLAN as "tag" and in another one as "untag" port. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 47114
* ramips: Add build files for HiWiFi HC5x61 modelsJohn Crispin2015-10-052-0/+53
| | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Spaces -> Tabs 2: Removed some packages Signed-off-by: Xiaoning Kang <kangxn@163.com> SVN-Revision: 47113
* ramips: Add DTS files for HiWiFi HC5x61 modelsJohn Crispin2015-10-054-0/+299
| | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Merged most stuff into dtsi file 2: Remove unnecessary empty lines. Signed-off-by: Xiaoning Kang <kangxn@163.com> SVN-Revision: 47112
* ramips: Add base-files for HiWiFi HC5x61 modelsJohn Crispin2015-10-055-10/+45
| | | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Fixed model order 2: Remove manufacturer name from model name 3: Use a hacky but prettier way to get mac address. Signed-off-by: Xiaoning Kang <kangxn@163.com> SVN-Revision: 47111
* ralink: add irq to mt7628 gpio nodeJohn Crispin2015-10-011-0/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47076
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 04:15:31 +0000