summaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: set the wifi mac address to the same as LAN on witiFelix Fietkau2016-01-011-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48029
* ramips: add a script to fix up the broken mac address on the witi boardFelix Fietkau2016-01-011-1/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48027
* ramips: fix inverted LEDs for RE6500Felix Fietkau2016-01-011-2/+2
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48022
* ramips: add mac address assignment for eth0 on RE6500Felix Fietkau2016-01-011-0/+4
| | | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48021
* ramips: fix firmware partition sizeFelix Fietkau2016-01-011-1/+1
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48020
* ramips: fix memory size for RE6500Felix Fietkau2016-01-011-1/+1
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48019
* ramips: disable NAND device in mt7621.dtsi to fix boot errors on many devicesFelix Fietkau2015-12-193-12/+4
| | | | | | | | Enable it from .dts files that need it, also remove redundant properties Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47936
* ramips: update DTS files to use jedec,spi-nor compatible string for m25p80 ↵Felix Fietkau2015-12-1894-94/+94
| | | | | | | | to fix probe issues Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47935
* ralink: fixup devicetree files to work with new ethernet driverJohn Crispin2015-12-17139-176/+190
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47900
* ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)John Crispin2015-12-121-0/+119
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
* ramips: move partition definitions out of mt7621.dtsi fileJohn Crispin2015-12-122-20/+22
| | | | | | | | | Partitions defined in parent dtsi cannot be undefined in children. This moves partitions defined in mt7621.dtsi into board's device tree. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47876
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-121-0/+26
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47875
* Revert "ramips: use gic timer as clocksource for mt7621"Felix Fietkau2015-12-111-14/+0
| | | | | | This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7. SVN-Revision: 47872
* ramips: add additional support for MQmaker WiTi boardJohn Crispin2015-12-111-0/+146
| | | | | | | | | | | | | | The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna. This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 47845
* ramips: Fix support for PBR-M1 boardJohn Crispin2015-12-111-14/+53
| | | | | | | | | | The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it. The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds. Signed-off-by: 郭传鈜 <gch981213@gmail.com> SVN-Revision: 47844
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-111-0/+14
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47843
* ramips: enable CPS for mt7621John Crispin2015-12-111-1/+1
| | | | | | | | | | | | | Enables CPS multiprocessing instead ob obsoleted CMP for mt7621. This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx: * iperf shows only 50Mbits on direct gigabit connection to desktop, * ping times jump to 5-6ms to dorectly connected desktop * /proc/interrupts shows spurious interrups (ERR) Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47842
* ramips: mt7621: use symbolic names of gic interrupt settingsJohn Crispin2015-12-1111-18/+30
| | | | | | | | This also adds dts nodes for cpc and mc for documentation purposes Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47836
* ralink: bump to the target to v4.3John Crispin2015-12-101-14/+18
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47831
* ramips: adapt VoCore to new second spi device codeJohn Crispin2015-11-283-70/+66
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47667
* ralink: add support for netis WF-2881John Crispin2015-11-241-0/+133
| | | | | | | | | | | | | | | | | | | | | | | | | netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN. It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. this device only works on top of UBI. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons (reset button) * ethernet switch and USB diag LEDs * UART * GPIOs * sysupgrade Tested and not working * failsafe Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 47619
* ramips: add support for Youku YK1John Crispin2015-11-241-0/+127
| | | | | | | | | Changes since V1: I resend this patch for current trunk.The former V1 patch is for CC branch. Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47617
* ramips: update dtsi files to support second spi deviceJohn Crispin2015-11-226-12/+143
| | | | | | Signed-off-by: Michael Lee <igvtee@gmail.com> SVN-Revision: 47580
* ramips: init usb power for Lenovo Y1SJohn Crispin2015-11-211-0/+21
| | | | | | Signed-off-by: Shonn Lu <countrysideboy@qq.com> SVN-Revision: 47557
* ramips: minor tweak to the lks7688 baord nameJohn Crispin2015-11-051-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47388
* ramips: add support for ZBT WG2626John Crispin2015-11-021-0/+127
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47351
* ramips: add eeprom mtd partition to the Asus RP-N53 dtsJohn Crispin2015-11-021-0/+4
| | | | | | | | This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working. Signed-off-by: Alberto Mattea <alberto@mattea.info> SVN-Revision: 47350
* ramips: add support for Dovado tiny ACJohn Crispin2015-11-021-0/+166
| | | | | | | | | | | | | | | | Add support for Dovado tiny AC wifi router. Soc: mt7620a ram: 64MB flash: 8MB 1x usb 2.0 two gigabit lan ports 5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip. Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47348
* ramips: add alsa supportJohn Crispin2015-10-191-0/+111
| | | | | | | | | add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960. mt7620 is only compile tested. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47205
* ramips: add LinkIt Smart7688 supportJohn Crispin2015-10-191-0/+173
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47203
* ramips: fix /target/linux/ramips/dts/HC5XXX.dtsiJohn Crispin2015-10-071-2/+0
| | | | | | | | dtb complained about those lines Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47151
* ramips: add support for 16MB VoCoreJohn Crispin2015-10-053-34/+82
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47120
* ramips: fix size-cells for spi nodesJohn Crispin2015-10-056-6/+6
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47119
* ramips: Add DTS files for HiWiFi HC5x61 modelsJohn Crispin2015-10-054-0/+299
| | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Merged most stuff into dtsi file 2: Remove unnecessary empty lines. Signed-off-by: Xiaoning Kang <kangxn@163.com> SVN-Revision: 47112
* ralink: add irq to mt7628 gpio nodeJohn Crispin2015-10-011-0/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47076
* ramips: Fix pinmux functions for MT7621John Crispin2015-09-161-7/+7
| | | | | | | | | The pinctrl-rt2880 code doesn't support multiple functions with the same name. This will result in a incorrect pinmux configuration. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46963
* ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350John Crispin2015-09-141-0/+180
| | | | | | | | This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor. Signed-off-by: Tobias Welz <tw@wiznet.eu> SVN-Revision: 46921
* ramips: add support for Planex DB-WRT01John Crispin2015-09-141-0/+100
| | | | | | | | | | This patch add support for Planex DB-WRT01. DANBOARD route on the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio. DANBOARD is Cartoon character. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 46918
* ramips: enable external amplifier for Xiaomi MiWiFi MiniFelix Fietkau2015-09-121-0/+5
| | | | | | | | Attempt to boost the 2.4 GHz signal, currently very low. Signed-off-by: D. Andrei Măceș <dmaces@nd.edu> SVN-Revision: 46891
* ramips: use consistent naming scheme for LEDsJohn Crispin2015-08-1778-267/+267
| | | | | | | | | | | | | The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach. The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target: * fixes wrong indentation * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body) * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files) * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46664
* ramips: fix 7Links PX-4885 dts{, i}, board, image and profile namesJohn Crispin2015-08-173-5/+5
| | | | | | | | The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46629
* ramips: fix Buffalo WMR-300 dts, board, image and profile namesJohn Crispin2015-08-171-3/+3
| | | | | | | | The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46628
* ramips: fix Omnima models, images and profiles namesJohn Crispin2015-08-173-15/+15
| | | | | | | | | | | | | | | | | | | | Official names for supported Omnima products are (as on website): * Omnima HPM * Omnima MiniEMBWiFi * Omnima MiniEMBPlug This patch changes: * board names * dts filenames * profile names * image filenames * LED names for Omnima devices, for consistency. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46627
* ramips: fix Tenda W150M model nameJohn Crispin2015-08-171-2/+2
| | | | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46625
* ramips: fix Aigale Ai-BR100 dts and profile namesJohn Crispin2015-08-171-1/+1
| | | | | | | | The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46624
* ramips: fix Olimex models, images and profiles namesJohn Crispin2015-08-172-3/+3
| | | | | | | | | | | | | | Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website. The following patch: * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}" * changes filenames of dts and profile files * changes image filenames for Olimex RT5350F-OLinuXino{,-EVB} devices. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46623
* ramips: fix Sitecom WL-341v3 board and image namesJohn Crispin2015-08-171-8/+8
| | | | | | | | | | | | | The following patch changes: * board name from "wl341v3" to "wl-341v3" * dts filename * LED names in dts file for Sitecom WL-341v3 device. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46622
* ramips: fix Argus ATP-52B board and image namesJohn Crispin2015-08-171-3/+3
| | | | | | | | | | | | | | The following patch: * changes board name from "argus-atp52b" to "atp-52b" * changes dts filename * fixes LED names in dts file and base-files scripts * removes manufacturer name from image filename for Argus ATP-52B device. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46621
* ramips: fix Asus RT-N56U dts filenameJohn Crispin2015-08-171-0/+0
| | | | | | | | Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46619
* ramips: fix UPVEL model namesJohn Crispin2015-08-172-2/+2
| | | | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46618
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 21:31:17 +0000