summaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: fix support Planex MZK-750DHP.John Crispin2016-04-201-4/+22
| | | | | | | | | | fix script for Planex MZK-750DHP. modification of the GPIO definition. add Profile. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49205
* ramips: rt3352 usbphy fix in dts-fileJohn Crispin2016-04-201-1/+8
| | | | | | | | Add missing rt3352 usb phy. Fix ticket #20499. Signed-Off-By:Serge Vasilugin <vasilugin@yandex.ru> SVN-Revision: 49204
* ramips: Fixes for LinkIt 7688John Crispin2016-04-091-0/+4
| | | | | | | | | | | | | Misc fixes for LinkIt 7688 board: - Copy the right wireless firmware for the mt7688 - Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4. - Remove SPI_DEV from linux config which otherwise causes a massive warning - Add wmac to LINKIT7688.dts so wireless works Signed-off-by: Adam Kent <adam@semicircular.net> SVN-Revision: 49130
* ramips: fix for Planex MZK-WDPR (lcd control gpio).John Crispin2016-04-091-0/+10
| | | | | | | | | add lcd control gpio pin for Planex MZK-WDPR. LCD board initial timming is GPIO control. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49128
* ramips: MiWifi-Nano - change gpios to leds, add to default build groupJohn Crispin2016-03-201-23/+15
| | | | | | | | | | | | 1) Use leds to indicate: Red - Power Amber - Radio On Blue - Wifi associated 2) Add profile to default build group for MT7628 subtarget Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> SVN-Revision: 49045
* ramips: Add support for Xiaomi MiWiFi NanoJohn Crispin2016-03-161-0/+99
| | | | | | | | | | | | | | | Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> v3 includes changes suggested by L. D. Pinney & Karl Palsson- Eliminate en25q64 (4MB) flash chip Alphabetization Remove hyphen in model Rename profile from miwifinano.mk to xiaomi.mk Add gpios that are attached to leds SVN-Revision: 49024
* ramips: Add support for GL-MT750John Crispin2016-03-101-0/+159
| | | | | | | | This patch adds support for GL-MT750. GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps. It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support. SVN-Revision: 48994
* ramips: Add support for GL-MT300NJohn Crispin2016-03-101-0/+153
| | | | | | | | This patch adds support for GL-MT300N. GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM, 2 LANs, USB, UART, GPIO and PoE support. SVN-Revision: 48993
* ramips: Add support for GL-MT300AJohn Crispin2016-03-101-0/+164
| | | | | | | | This patches adds support for GL-MT300A. GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM, Two LANs, USB, UART and MMC daughter board. SVN-Revision: 48992
* ramips: add support for Planex MZK-WDPR.John Crispin2016-03-081-0/+76
| | | | | | | | | | | add support for Planex MZK-WDPR. MZK-WDPR(MZK-WDPR-R01) is internet radio tuner. This patch is "network board" in MZK-WDPR. LCD board is non OpenWrt Platform. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 48968
* ramips: add linux 4.4 support, update mt7621 subtarget to 4.4Felix Fietkau2016-03-071-2/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48951
* ramips: mt7621: fix WF-2881 for ubi splitJohn Crispin2016-03-041-12/+2
| | | | | | | | This patch fix firmware split for WF-2881 which was previously manually partitioned. Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 48908
* ramips: Add device tree for JCG JHR-N926RJohn Crispin2016-03-041-0/+127
| | | | | | | | | | | | | | | | Add a device tree for JCG JHR-N825R This router is based on a RT3052 and has 4MB of CFI flash and 32MB of SDRAM. As a special feature, it comes with a two digit seven segment display that is connected to a pair of daisy-chained 74164 shift registers that can be controlled via GPIOs. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48904
* ramips: Add device tree for JCG JHR-N825RJohn Crispin2016-03-041-0/+81
| | | | | | | | | | | | Add a device tree for JCG JHR-N825R This router is based on a RT3052 and has 4MB of CFI flash and 32MB of SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48903
* ramips: Add device tree for JCG JHR-N805RJohn Crispin2016-03-041-0/+89
| | | | | | | | | | | | Add a device tree for JCG JHR-N805R This router is based on a RT3050 and has 4MB of SPI flash and 16MB of SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48902
* ramips: Added support for ZBT-826 / ZBT-1026John Crispin2016-03-011-0/+124
| | | | | | | | | Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826 Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996 Signed-off-by: Jamie Stuart <jamie@onebillion.org> SVN-Revision: 48865
* ramips: create device tree node for MT7628 WMAC in preparation for future ↵Felix Fietkau2016-02-282-0/+17
| | | | | | | | work on driver support in mt76 Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48812
* ramips: fix GPIO names for RT5350F-OLinuXino-EVBJohn Crispin2016-02-261-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hi, the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14 as relay2 and relay1 respectively, as you can see from their rt5350f branch on GitHub. For some reason in the official stable build both the GPIOs are swapped and the wrong names are declared in the gpio-export directive. I'm submitting this patch which should roll back the wrong changes, so that we get backward compatibility with any script developed on RC3 which controls the relays. After patching correct operation is restored: root@OpenWrt:/# cat /sys/kernel/debug/gpio GPIOs 0-21, platform/10000600.gpio, 10000600.gpio: gpio-0 (button ) in hi gpio-12 (relay2 ) out lo gpio-14 (relay1 ) out lo Thank you, Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net> SVN-Revision: 48796
* ramips: fix WSR-1166 partition tableFelix Fietkau2016-02-221-2/+2
| | | | | | | | | - Fix typo in board_data partition start address - Increase board_data partition size in order to exploit all flash size Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> SVN-Revision: 48751
* ralink: fix mt7628 ehci supportJohn Crispin2016-02-191-1/+2
| | | | | | | | the u2_phy init was missing Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 48747
* ramips: Add support for Phicomm PSG1208John Crispin2016-02-151-0/+114
| | | | | | | | | | This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram. The WPS led is uesd as status_led because the power light can't be controlled with GPIO. It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> SVN-Revision: 48721
* ramips: Support LEDs on D-Link DIR-860L B1John Crispin2016-02-121-0/+20
| | | | | | | | Adds the required gpio definitions. Signed-off-by: Johannes Wienke <languitar@semipol.de> SVN-Revision: 48715
* ramips: Add support for Netgear EX2700John Crispin2016-02-121-0/+148
| | | | | | | | | | | | | | | | This patch adds support for the Netgear EX2700 and builds an approriate sysupgrade image. What's missing is the option to build a factory image flashable via the router's stock web interface, but this approach is hindered by the fact that u-boot operforms an additional integrity check, which expects a uImage header in the last 64 bytes of the "kernel" partition, which the bootloader expects to be 960k, a size exceeded by the standard OpenWrt kernel. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> SVN-Revision: 48698
* ramips: HLK-RM04 - Enable GPIO14 for WPS buttonJohn Crispin2016-02-084-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The top half of UARTF on the HLK-RM04 is used for GPIO. mode 1 mode 2 RIN GPIO14 DSR_N GPIO13 DCD_N GPIO12 DTR_N GPIO11 RXD GPIO10 CTS_N GPIO09 TXD GPIO08 RTS_N GPIO07 This patch applies 3'b101 mode to UARTF: GPIO14 GPIO13 GPIO12 GPIO11 RXD CTS_N TXD RTS_N Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi). This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file. Signed-off-by: John Clark <inindev@gmail.com> SVN-Revision: 48665
* rampis: HLK-RM04 - Setup I2C as GPIOJohn Crispin2016-02-081-1/+20
| | | | | | | | | | | | | | | | | | | The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2. Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0 Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1 group mode 1 mode 2 hlk-rm04 pin & export i2c i2c_sd gpio1 (pin 8, hlk-rm04:gpio0) i2c i2c_sclk gpio2 (pin 9, hlk-rm04:gpio1) reference: http://www.hlktech.net/product_detail.php?ProId=39 http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf Signed-off-by: John Clark <inindev@gmail.com> SVN-Revision: 48664
* ramips: HLK-RM04 - Fix push button functionsJohn Crispin2016-02-081-3/+7
| | | | | | | | | The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198 The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211 Signed-off-by: John Clark <inindev@gmail.com> SVN-Revision: 48663
* ramips: HLK-RM04 - Remove power LED configJohn Crispin2016-02-081-9/+0
| | | | | | | | | The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it. (Note that GPIO0 is actually connected to the RESET button.) Signed-off-by: John Clark <inindev@gmail.com> SVN-Revision: 48662
* ramips: fix serial baudrate for final version of ZBT-WG2626 boardJohn Crispin2016-01-191-1/+1
| | | | | | | | | | The bootloader was updated and now uses 115200 instead of 57600 baud for the serial console. Change this also in OpenWrt's DTS, so the rate is consistent for bootloader and linux kernel output. Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 48359
* ramips: fix duplicate /dts-v1/ line for WRTNODE2Felix Fietkau2016-01-061-2/+0
| | | | | | Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> SVN-Revision: 48138
* ralink: update the usb phy driver to the version sent upstreamJohn Crispin2016-01-046-8/+8
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 48114
* ralink: fix USB compatible stringsJohn Crispin2016-01-046-12/+12
| | | | | | | | switch to the upstream compatible strings for ehci and ohci support. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 48113
* ramips: Remove LED GPIO definitions in MQmaker WiTi device treeJohn Crispin2016-01-011-19/+0
| | | | | | | | LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 48055
* ralink: add WRTnode2 platform and led supportJohn Crispin2016-01-013-0/+149
| | | | | | Signed-off-by: xzmu <xzmu@wrtnode.com> SVN-Revision: 48049
* ramips: set the wifi mac address to the same as LAN on witiFelix Fietkau2016-01-011-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48029
* ramips: add a script to fix up the broken mac address on the witi boardFelix Fietkau2016-01-011-1/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48027
* ramips: fix inverted LEDs for RE6500Felix Fietkau2016-01-011-2/+2
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48022
* ramips: add mac address assignment for eth0 on RE6500Felix Fietkau2016-01-011-0/+4
| | | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48021
* ramips: fix firmware partition sizeFelix Fietkau2016-01-011-1/+1
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48020
* ramips: fix memory size for RE6500Felix Fietkau2016-01-011-1/+1
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48019
* ramips: disable NAND device in mt7621.dtsi to fix boot errors on many devicesFelix Fietkau2015-12-193-12/+4
| | | | | | | | Enable it from .dts files that need it, also remove redundant properties Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47936
* ramips: update DTS files to use jedec,spi-nor compatible string for m25p80 ↵Felix Fietkau2015-12-1894-94/+94
| | | | | | | | to fix probe issues Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47935
* ralink: fixup devicetree files to work with new ethernet driverJohn Crispin2015-12-17139-176/+190
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47900
* ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)John Crispin2015-12-121-0/+119
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
* ramips: move partition definitions out of mt7621.dtsi fileJohn Crispin2015-12-122-20/+22
| | | | | | | | | Partitions defined in parent dtsi cannot be undefined in children. This moves partitions defined in mt7621.dtsi into board's device tree. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47876
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-121-0/+26
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47875
* Revert "ramips: use gic timer as clocksource for mt7621"Felix Fietkau2015-12-111-14/+0
| | | | | | This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7. SVN-Revision: 47872
* ramips: add additional support for MQmaker WiTi boardJohn Crispin2015-12-111-0/+146
| | | | | | | | | | | | | | The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna. This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 47845
* ramips: Fix support for PBR-M1 boardJohn Crispin2015-12-111-14/+53
| | | | | | | | | | The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it. The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds. Signed-off-by: 郭传鈜 <gch981213@gmail.com> SVN-Revision: 47844
* ramips: use gic timer as clocksource for mt7621John Crispin2015-12-111-0/+14
| | | | | | | | | | * Switches clocksource to gic timer. * Moves frequency definitions to dtsi since frequency was hardcoded anyway Will work on proper frequency detection later. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47843
* ramips: enable CPS for mt7621John Crispin2015-12-111-1/+1
| | | | | | | | | | | | | Enables CPS multiprocessing instead ob obsoleted CMP for mt7621. This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx: * iperf shows only 50Mbits on direct gigabit connection to desktop, * ping times jump to 5-6ms to dorectly connected desktop * /proc/interrupts shows spurious interrups (ERR) Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47842
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-29 15:12:28 +0000