summaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq/dts
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: Add the xbar to vr9.dtsJohn Crispin2016-01-011-1/+5
| | | | | | | | linux 4.4 (since commit 08b3c894e56580b8ed3e601212a25bda974c3cc2 "MIPS: lantiq: Disable xbar fpi burst mode") requires that the xbar is defined in the .dts of vrx200 (VR9) SoCs. SVN-Revision: 48056
* lantiq: TDW8980 - use devicename:colour:function led naming schemeJohn Crispin2016-01-011-1/+1
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48044
* lantiq: P2812HNUFX - move usb leds to P2812HNU-F1John Crispin2016-01-012-10/+18
| | | | | | | | | | The P2812HNU-F3 doesn't have usb leds. Only the P2812HNU-F1 has those leds. Reported-by: Sylwester Petela <sscapi@gmail.com> Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48043
* lantiq: use devicename:colour:function led naming schemeJohn Crispin2016-01-0129-368/+392
| | | | | | | | | | | | | | | | The leds of the following boards are not renamed due to lack of manuals/informations: - ARV7519PW - ARV7510PW22 - ARV4510PW The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't match the leds from the manual or pictures (e.g. there shouldn't be a wps led). Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48042
* lantiq: add support for indicating the boot state using three ledsJohn Crispin2016-01-0131-78/+173
| | | | | | | | | | | | | | The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48041
* lantiq: use dsl led defined in DTSJohn Crispin2016-01-012-2/+2
| | | | | | | | | | | | | | | | | dsl_control (dsl_notify.sh) is the only process which is aware of the state of the atm/ptm interface. Use the dsl led exclusive for the dsl line state. On boards which don't have a distinct internet and a dsl led, let the netdev status of the atm interface trigger the shared led. Triggering the shared led according to the status of the ppp interface isn't suitable, since the led would be switched of if the ppp connection goes down, but the line is still in sync. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48040
* lantiq: define default leds in dts filesJohn Crispin2016-01-0131-135/+371
| | | | | | | | | | - ARV7525PW: use the power led as dsl led as done by the stock firmware - FRITZ3370: use the info led as internet led - FRITZ7320: use the power led as dsl led as done by the stock firmware Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48037
* lantiq: ARV752DPW - fix dts fileJohn Crispin2016-01-011-9/+13
| | | | | | | | | | | | | | Use the same led logic and labels as the OEM firmware (red = okay, blue = failure). Add the red internet led. Remove missing usb led workaround. The workaround shouldn't be in the default configuration. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48036
* lantiq: ARV752DPW22 - fix dts fileJohn Crispin2016-01-011-22/+12
| | | | | | | | | | | No need to switch (and keep) on all leds at boot. Use the same led logic and labels as the OEM firmware (red = okay, blue = failure). Add the red internet led. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48035
* lantiq: DGN1000B - fix typo in dts fileJohn Crispin2016-01-011-1/+1
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48034
* lantiq: ARV4518PWR01* move redundant parts to dtsiJohn Crispin2016-01-013-356/+186
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48033
* lantiq: P2812HNUFX - move leds to dtsiJohn Crispin2016-01-013-114/+61
| | | | | | | | Beside the used labels, they are the same on both boards. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48031
* lantiq: TDW89x0 - increase spi frequencyJohn Crispin2015-12-231-2/+4
| | | | | | | | | | | | | | | | | Use the same max spi frequency as set in u-boot. According to the datasheets, the Q64-104HIP as well as the Winbond 25Q64FVSIG support spi frequencies up to 50 MHz. During my tests, the Q64-104HIP couldn't be recognized/initialized if the frequency was > 40MHz. Both chips do support fast read as well. While touching the dts file, I fixed the dtc compiler warnings. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 47994
* lantiq: Configure LED polarity for TDW8970 and TDW8980.John Crispin2015-12-232-4/+1
| | | | | | | | | This patch configures the correct ath9k WLAN LED polarity for the TDW8970, and for the TDW8980 as well. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> SVN-Revision: 47969
* lantiq: fix ARV7519RW22 buttonsJohn Crispin2015-12-171-7/+7
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 47918
* lantiq: add the TDW8980 5GHz ledJohn Crispin2015-12-171-0/+7
| | | | | | | | | Still unused, but u-boot doesn't take care of the led, which results in a permanent switched on 5GHz LED. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 47915
* lantiq: Configure LED polarity for TDW8970.John Crispin2015-12-171-0/+4
| | | | | | | | This patch configures the correct ath9k WLAN LED polarity for the TDW8970. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> SVN-Revision: 47913
* lantiq: Configure disabled WLAN bands for TDW89X0.John Crispin2015-12-171-0/+1
| | | | | | | | | | | | | | | | | The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family. The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family. This means that the chip for both routers is 2.4 GHz only. Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition (at least on my TDW8970). So this patch disables the 5 GHz band. Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net> SVN-Revision: 47912
* lantiq: get rid of the dsl_fw mtd partitionFelix Fietkau2015-12-053-18/+3
| | | | | | | | | Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware, we can drop the dsl_fw partition and extend the firmware partition. Signed-off-by: Andre Heider <a.heider@gmail.com> SVN-Revision: 47783
* lantiq: re-enable spi-xway for TD-W89X0 now that it is fixedFelix Fietkau2015-12-041-58/+46
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47768
* lantiq: fix up m25p80 device ids (#20975)Felix Fietkau2015-12-025-10/+5
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 47690
* Revert "lantiq: activate spi-xway on TDW89X0"John Crispin2015-10-191-47/+59
| | | | | | | | | | This reverts commit 68c2e4789b4f071ee75d39248f4d08fe8283eb28. commit r47159 was bad Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47207
* lantiq: activate spi-xway on TDW89X0John Crispin2015-10-071-59/+47
| | | | | | | | use the hardware spi core in favour of spi-gpio. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 47159
* lantiq: several ARV7519RW22 fixesJohn Crispin2015-10-051-9/+13
| | | | | | | | | | | | | | Fixes ARV7519RW22 flash register (only 1 flash). Power LED is green, not red. Rename message LEDs to internet. Add LEDs configuration (lan, wan, power). Enable switch VLANs. Fix secondary USB. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com> SVN-Revision: 47132
* lantiq: Add target TP-Link TD-W8980John Crispin2015-10-053-250/+284
| | | | | | | | | The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 47130
* lantiq: Introduce DWC2 compatible DTS definitions for AR9 USBJohn Crispin2015-09-141-1/+10
| | | | | | | | | | | | Since the AR9 USB is very similar to the VR9 USB it too can be used with the upstream DWC2 driver. Here are the DTS definitions which make it compatible with the DWC2 driver. Signed-off-by: Antti Seppälä <a.seppala@gmail.com> SVN-Revision: 46914
* lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V)John Crispin2015-07-071-0/+162
| | | | | | | | lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V) Signed-off-by: Jannis Pinter <jannis@pinterjann.is> SVN-Revision: 46224
* lantiq: Add support for the BT Home Hub 5AJohn Crispin2015-07-071-0/+287
| | | | | | | | | | | | | | | u-boot support depends on the next "upstream" version ([0]) from Daniel Schwierzeck. Since the installation process is quite complicated a "how to" was added to the wiki: [1] [0] https://github.com/danielschwierzeck/u-boot-lantiq/tree/openwrt/v2014.01-next [1] http://wiki.openwrt.org/toh/bt/homehub_v5a V2: Use the correct PCI interrupt (fixes 2.4GHz wifi) Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46223
* lantiq: Make the MEI address available for kernel driversJohn Crispin2015-07-071-0/+1
| | | | | | | | Newer DSL driver versions depend on the address information. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46221
* lantiq: Add support for Arcadyan VGV7510KW22 (known as o2 Box 6431)John Crispin2015-06-053-0/+342
| | | | SVN-Revision: 45897
* lantiq: fix VG3503J rootfs offsetJonas Gorski2015-06-011-1/+1
| | | | | | | | | | In r44391 the kernel partion size was increased to allow larger kernels, but the rootfs partition offset was missed. Fix this by setting the rootfs offset to the expected value. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45868
* lantiq: Convert Zyxel P-2812HNU-FX and TP-Link TD-W8970 to support dwc2John Crispin2015-03-113-1/+19
| | | | | | | | | | | | | | Here the device tree entry for ifxhcd is listed as compatible with one supported in dwc2 (after patching the dwc driver appropriately). A second entry is added to support the second core of the hcd. This entry is listed to be compatible with only dwc2. Done this way there should be backwards support for both hcd drivers (ltq-hcd and dwc2) Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> SVN-Revision: 44676
* lantiq: fix DGN3500 root deviceJohn Crispin2015-02-131-1/+1
| | | | | | Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44428
* lantiq: fix VG3503J partition table for newer kernelsJohn Crispin2015-02-111-2/+2
| | | | | | | | the kernel has increased and does not fit into the 1,5MB anymore. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44391
* lantiq: td-w8970: fix reset buttonJohn Crispin2015-02-091-2/+2
| | | | | | | | For TP-LINK TD-W8970 button should work as "reset", not "BTN_1". Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 44352
* lantiq: add 3.18 supportJohn Crispin2015-02-096-340/+12
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44348
* lantiq: DGN3500 cleanupsJohn Crispin2015-01-181-1/+1
| | | | | | | | | This patch builds on the previous three to streamline support for the Netgear DGN3500. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44032
* Remove old P2812HNUFX dtsJohn Crispin2015-01-171-308/+0
| | | | | | | | Remove unused P2812HNUFX board definition. Signed-off-by: Sylwester Petela <sscapi@gmail.com> SVN-Revision: 43988
* lantiq: Add device tree for P2812HNUF1 and P2812HNUF3John Crispin2015-01-173-0/+472
| | | | | | | | Add device tree for P2812HNUF1 and P2812HNUF3. Signed-off-by: Sylwester Petela <sscapi@gmail.com> SVN-Revision: 43986
* lantiq: BT Home Hub3A - device treeJohn Crispin2015-01-081-0/+210
| | | | | | | | BT Home Hub3A - device tree Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> SVN-Revision: 43877
* lantiq: vgv7519: fix board_config on dts, read mac address and setJohn Crispin2014-10-292-14/+10
| | | | | | Signed-off-by: Eddi De Pieri <eddi@depieri.net> SVN-Revision: 43109
* vgv7519: support more recent board release with vrx288 v1.2John Crispin2014-10-261-1/+2
| | | | | | | | The existance of this new board has been confirmed and tested by the guy on this commit https://github.com/openwrt-vgv7519/uboot-bin/commit/76fdd8e638f81e324ffe77856481bd147398f6e8 SVN-Revision: 43072
* lantiq: allow pcie to be disabled by dts + vgv7519 fix pci irq + disable ↵John Crispin2014-10-141-1/+5
| | | | | | | | pcie by dts Signed-off-by: Eddi De Pieri <eddi@depieri.net> SVN-Revision: 42907
* lantiq - vgv7519: load rt5362 eeprom from bootloader param patitionJohn Crispin2014-10-063-0/+19
| | | | SVN-Revision: 42824
* lantiq - vgv7519: enable pci busJohn Crispin2014-10-061-2/+3
| | | | SVN-Revision: 42823
* lantiq - vgv7519: remove spi_cs4, since the board use this line for ↵John Crispin2014-10-061-1/+1
| | | | | | something else SVN-Revision: 42822
* lantiq - vgv7519: fix open-drain configuration for stpJohn Crispin2014-10-061-8/+6
| | | | SVN-Revision: 42821
* lantiq - vgv7519: add pci-rst entry into dtsJohn Crispin2014-10-061-0/+6
| | | | SVN-Revision: 42820
* lantiq - vgv7519: remove exin definition copied from dev-board dtsJohn Crispin2014-10-061-8/+0
| | | | SVN-Revision: 42819
* lantiq - vgv7519: we don't have pcie bus so we don't need the reset device ↵John Crispin2014-10-061-5/+0
| | | | | | tree for this board SVN-Revision: 42818
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 21:48:59 +0000