summaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/base-files/etc/diag.sh
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker GatewayChris Blake2016-09-271-0/+3
| | | | | | | | | This patch adds support for Cisco's Z1. Detailed instructions for the flashing the device can be found in the OpenWrt wiki: <https://wiki.openwrt.org/toh/meraki/z1> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ar71xx: add support for Zbtlink ZBT-WE1526Piotr Dymacz2016-08-181-0/+3
| | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 650/400/200 MHz (CPU/DDR/AHB) - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - two external, non-detachable antennas - 8x LED, 1x button - UART header (pinout: VCC, RX, TX, GND) Flash instruction: Use sysupgrade in vendor firmare which is based on OpenWrt. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for gl-ar300mZhao Gang2016-07-201-0/+3
| | | | | | | This add initial support for gl-ar300m router. Product page: http://www.gl-inet.com/ar300m/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* ar71xx: add support for jjPlus JWAP230Piotr Dymacz2016-07-131-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 2x 10/100/1000 Mbps Ethernet - 128 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm - 3x MMCX connectors - power input: 802.3at PoE or wide range DC (36-57 V) - optional 802.3af PSE - 1x mini-PCIe connector with PCIe, USB buses and SIM slot - 1x mini-PCIe connector with PCIe bus - 1x USB type-A connector - 6x LED, 1x button (hardware reset) - RS232 (MAX3223) and (E)JTAG headers Default configuration: - WAN on eth1 (RJ45 near LEDs with PoE input) - LAN on eth0 (RJ45 near DC jack) - left top LED set to be status LED - all LEDs configurable form user space Flash instruction (do it under U-Boot, using RS232): 1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Wallys DR531Piotr Dymacz2016-07-131-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Short specification: - 550/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm - 2x MMCX connectors - mini-PCIe connector with PCIe/USB buses and SIM slot - 7x LED, 1x button, 1x optional buzzer - UART, (E)JTAG and LED headers Default configuration: - WAN on eth1 (RJ45 near DC jack) - LAN on eth0 (RJ45 near button) - S4 LED set to be status LED - all LEDs configurable form user space - button configured for reset Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for OpenEmbed SOM9331Allan Nick Pedrana2016-06-071-0/+3
| | | | | | | | This patch adds the target profile SOM9331 and configures hardware functionality for the 3x Eth Ports & corresponding LED's, the USB Host, the USART to USB bridge and the System LED. Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
* ar71xx: Fix TL-WR841N v11 LEDs, use separate machineStijn Segers2016-05-311-0/+1
| | | | Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* ar71xx: add user-space support for the OpenMesh MR1750v2Sven Eckelmann2016-05-231-1/+2
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add user-space support for the OpenMesh OM2P-HSv3Sven Eckelmann2016-05-231-0/+1
| | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ar71xx: add support for TP-LINK TL-WR842N/ND v3Cezary Jackiewicz2016-05-141-0/+1
| | | | | | | | | | | - CPU QCA9531-BL3A - RAM: 64MB - flash: 16MB - USB AP143 platform, similar to tl-wr841n v10/v11, but with USB Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ar71xx: Add support for Ubiquiti UniFi AP AC PROP.Wassi2016-05-121-1/+2
| | | | | Add support for the Ubiquiti UniFi AP AC PRO Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: Rename unifiac to unifiac-liteP.Wassi2016-05-121-1/+1
| | | | | | | To avoid confusion with different unifiac devices, rename existing target "unifiac" to "unifiac-lite", before "unifiac-pro" is introduced. Signed-off-by: P.Wassi <p.wassi at gmx.at>
* ar71xx: add TP-Link TL-WR810N supportblogic2016-05-101-0/+1
| | | | | | | | | This patch adds support for the TP-Link TL-WR810N. https://wiki.openwrt.org/toh/tp-link/tl-wr810n Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com> SVN-Revision: 49286
* ar71xx: Add support for the OMYlink OMY-G1John Crispin2016-04-261-0/+3
| | | | | | | | | | https://wiki.openwrt.org/toh/omylink/omy-g1 http://www.omylink.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49258
* ar71xx: add TP-Link TL-WA901ND-v4 supportJohn Crispin2016-04-091-0/+1
| | | | | | Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com> SVN-Revision: 49158
* ar71xx: add support for Compex WPJ342John Crispin2016-04-091-0/+3
| | | | | | | | | | | | OpenWrt can be flashed with following uboot commands: tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize Signed-off-by: Christian Mehlis <christian@m3hlis.de> SVN-Revision: 49157
* ar71xx: add user-space support for the OpenMesh OM5P-ACv2John Crispin2016-04-091-1/+2
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49150
* ar71xx: add user-space support for the OpenMesh OM5P-ACJohn Crispin2016-04-091-0/+3
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> SVN-Revision: 49142
* ar71xx: Add support for the OMYlink OMY-X1John Crispin2016-03-161-0/+3
| | | | | | | | | | | | This patch adds support for the OMYlink OMY-X1 https://wiki.openwrt.org/toh/omylink/omy-x1 http://www.omylink.com/ Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49026
* ar71xx: add support for the Telldus TellStick ZNet LiteJohn Crispin2016-03-101-0/+3
| | | | | | Signed-off-by: Micke Prag <micke.prag@telldus.se> SVN-Revision: 48977
* ar71xx: WNR2000v3: enable control of all LEDs and buttonsFelix Fietkau2016-03-051-0/+1
| | | | | | | | | This patch provides full GPIO support for WNR2000v3 (LEDs and buttons). It exposes all LEDs to operating system, including Ethernet ones. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48922
* ar71xx: Support for Ubiquiti UniFi AP AC LITEJohn Crispin2016-02-121-1/+2
| | | | | | | Add support for the Ubiquiti UniFi AP AC LITE Signed-off-by: P.Wassi <p.wassi at gmx.at> SVN-Revision: 48711
* ar71xx: add support for Netgear WPN824NJohn Crispin2016-01-191-1/+2
| | | | | | | | | | | | | | | | Add support for Netgear WPN824N. Hardware specs: * AR7240, 4 LAN ports, 1 WAN port * AR9285 WLAN * 32 MB RAM * 4 MB Flash * 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color effect) * 3 Buttons (not supported) Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> SVN-Revision: 48356
* V2 ar71xx : Add Support for the Bitmain Antrouter R1John Crispin2016-01-011-0/+3
| | | | | | | | | | This patch adds support for the Bitmain Antrouter R1 http://wiki.openwrt.org/toh/bitmain/r1 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 48058
* ar71xx: Add support for AirTight Networks C-55John Crispin2015-12-231-0/+3
| | | | | | | | This patch is to add support for the AirTight Networks C-55 Access Point Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47973
* ar71xx: PowerCloud CR5000 openwrt configurationFelix Fietkau2015-12-191-0/+3
| | | | | | | | | | | | OpenWrt configuration part of support for the PowerCloud Systems CR5000. The CR5000 is a dual-band 802.11n wireless router with 8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and five port gigabit ethernet switch. The CR5000 was sold as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47946
* ar71xx: PowerCloud CR3000 OpenWrt configurationFelix Fietkau2015-12-191-0/+3
| | | | | | | | | | | | OpenWRt configuration part of support for the PowerCloud Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast ethernet wan port that was sold by PowerCloud Systems as hardware for the Skydog cloud-managed router service. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47945
* ar71xx: PowerCloud CAP324 OpenWrt configurationFelix Fietkau2015-12-191-0/+3
| | | | | | | | | | | | | | | Openwrt configuration part of support for PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems who's stock firmware (CloudCommand) provides 'cloud' based managment of large numbers access points. The CAP324 is a dual-band 802.11n wireless access point with 16MB flash and 128MB RAM and single gigabit ethernet port. It can be powered via PoE or a wall wart. Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com> SVN-Revision: 47944
* ar71xx: add support for TRENDnet TEW-823DRUJohn Crispin2015-12-171-1/+2
| | | | | | | | | | | | | | Add support for TRENDnet TEW-823DRU: - cpu: QCA9558 @720MHz - flash: 16MB - ram: 256MB - 4+1 RJ45 100/1000Mbps - wifi: QCA9558 (bgn) and QCA9880-BR4A (ac) - 1x USB 2.0 Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 47927
* ar71xx: add support for Cisco's MR18John Crispin2015-12-121-0/+3
| | | | | | | | | | | This patch adds support for Cisco's MR18. Detailed instructions for the flashing the device can be found in the OpenWrt forum thread: <https://forum.openwrt.org/viewtopic.php?id=59248> Signed-off-by: Chris R Blake <chrisrblake93@gmail.com> SVN-Revision: 47878
* ar71xx: Add support for Wallys DR344John Crispin2015-12-111-0/+3
| | | | | | | | This patch is for Wallys DR344 support under OpenWRT Signed-off-by: Philippe Duchein <wireless-dev@duchein.net> SVN-Revision: 47847
* ar71xx: add support for the devolo dLAN HotspotJohn Crispin2015-11-211-0/+3
| | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 47554
* ar71xx: add support for TP-LINK TL-WR941ND v6 (international version)Felix Fietkau2015-11-081-1/+2
| | | | | | | | | | | | | | | The international version is completely different from the already supported Chinese version. The WLAN of the QCA956x SoC used by this router has been fixed in r46948. This patch looks like it changes a lot in 700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately, quilt decided to completely reorganize the Kconfig patch even though only a single section has been added. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 47420
* ar71xx: Add support for ZyXEL NBG6616.Felix Fietkau2015-11-071-1/+4
| | | | | | Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> SVN-Revision: 47405
* ar71xx: Add Gainstrong MiniBox v1.0 support to trunkJohn Crispin2015-10-191-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch supersedes the v1 from September 17th. Bumping the patch version - the MiniBox profile showed up under M, but since it's called 'Gainstrong MiniBox v1.0' now it looks out of place. Renamed the profile to gs-minibox-v1.mk to fix that. The following patch adds support for the Gainstrong MiniBox into trunk (or 'Designated Driver' :D ). Fixed items: - Inverted LED polarity (OOLITE seems to suffer from the same problem). - Changed uppercase MINIBOX_V1_ prefix as requested. - Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor). - Mention the vendor (Gainstrong) in code headers. Compiles fine, has been confirmed working by owners on 15.05. Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c, the MiniBox images build fine without, so I'm wondering: do I need to add it in there as well? Any added benefit? Thank you Signed-off by: Stijn Segers <francesco.borromini@inventati.org> SVN-Revision: 47234
* ar71xx: Bitmain Antminer S1 & S3 cleanupJohn Crispin2015-10-191-2/+4
| | | | | | | | | | | | Sets the LEDs to boardname:color:led-name Sets the LAN to eth0 Other corrections such as the Machine Name and HWIDs v2 corrects the profile names in the Makefile and changes tabs to spaces in the Makefile 'define Device/' like the other devices. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 47221
* ar71xx: Add UBNT airGateway Pro supportJohn Crispin2015-09-161-1/+2
| | | | | | | | This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro. Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com> SVN-Revision: 46961
* ar71xx: add TP-LINK TL-WDR3320 v2 supportJohn Crispin2015-09-141-0/+1
| | | | | | | | | | This patch adds support for TP-LINK TL-WDR3320 v2. This router uses a chinese version 2 firmware header,. Signed-off-by: Weijie Gao <hackpascal@gmail.com> SVN-Revision: 46934
* ar71xx: add user-space support for the OpenMesh MR1750 boardJohn Crispin2015-09-141-0/+3
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46927
* target: ar71xx: add support for COMFAST CF-E316N v2 boardFelix Fietkau2015-09-111-0/+3
| | | | | | | | | | | | This adds full support (sans sysupgrading from vendor firmware) for the COMFAST CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is actively refusing to provide GPL'd sources for the OpenWrt version they ship with the device, damn them). Signed-off-by: Paul Fertser <fercerpav@gmail.com> SVN-Revision: 46852
* ar71xx: add support for TP-Link TL-WDR6500 v2John Crispin2015-08-171-0/+3
| | | | | | | | | | | Signed-off-by: Weijie Gao <hackpascal@gmail.com> This patch adds support for TP-Link TL-WDR6500 v2. The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for the whole firmware, so I have to create a new firmware creation method. SVN-Revision: 46663
* ar71xx: Add support for Black SwiftJohn Crispin2015-08-171-0/+3
| | | | | | | | | | | | Add support for the Black Swift board: http://www.black-swift.com/ Took relevant parts and slightly adapted from: https://github.com/blackswift/openwrt/blob/master/bsb.patch Signed-off-by: Bruno Randolf <br1@einfach.org> SVN-Revision: 46651
* ar71xx: add support for Onion OmegaJohn Crispin2015-07-241-0/+3
| | | | | | | | | | | | This patch adds support for the Onion Omega. https://onion.io/omega Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Acked-by: Boken Lin <bl@onion.io> Tested-by: Jacky Huang <huangfangcheng@163.com> SVN-Revision: 46458
* ar71xx: Add support for AP147-010 reference boardJohn Crispin2015-07-241-0/+3
| | | | | | Signed-off-by: Sven Eckelmann <sven@open-mesh.com> SVN-Revision: 46457
* Revert "ar71xx: Add support for Cisco-Linksys WAP4410N" (r46250)Felix Fietkau2015-07-191-3/+0
| | | | | | | | The commit is incomplete, it does not even build the mach-* file This reverts commit 6e6adcf7a197b1802cb728ddcccf05f890ca0574 SVN-Revision: 46425
* ar71xx: add support for the devolo dLAN pro 1200+ WiFi acJohn Crispin2015-07-141-0/+3
| | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46342
* ar71xx: add support for the devolo dLAN pro 500 Wireless+John Crispin2015-07-141-0/+3
| | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> SVN-Revision: 46338
* ar71xx: Add support for Cisco-Linksys WAP4410NJohn Crispin2015-07-071-0/+3
| | | | | | | | | | This patch adds support for the Cisco WAP4410N, an access point that uses the AR9132 SoC. Web upgrades from stock are not yet possible, UART access required for the initial flash. Signed-off-by: Ryan A Young <rayoung@utexas.edu> SVN-Revision: 46250
* ar71xx: add support for D-Link DIR-615 rev. Ix boardJohn Crispin2015-07-071-0/+1
| | | | | | | | Based on trunk r46212. Signed-off-by: Jaehoon You <teslamint@gmail.com> SVN-Revision: 46248
* ar71xx: Add Support for the Bitmain Antminer S3John Crispin2015-07-071-1/+2
| | | | | | | | | | This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner http://wiki.openwrt.org/toh/bitmain/s3 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 46236
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-10 03:41:31 +0000