diff options
Diffstat (limited to 'package/mac80211/src/net/mac80211/Kconfig')
| -rw-r--r-- | package/mac80211/src/net/mac80211/Kconfig | 168 |
1 files changed, 0 insertions, 168 deletions
diff --git a/package/mac80211/src/net/mac80211/Kconfig b/package/mac80211/src/net/mac80211/Kconfig deleted file mode 100644 index 45c7c0c387..0000000000 --- a/package/mac80211/src/net/mac80211/Kconfig +++ /dev/null @@ -1,168 +0,0 @@ -config MAC80211 - tristate "Generic IEEE 802.11 Networking Stack (mac80211)" - select CRYPTO - select CRYPTO_ECB - select CRYPTO_ARC4 - select CRYPTO_AES - select CRC32 - select WIRELESS_EXT - select CFG80211 - select NET_SCH_FIFO - ---help--- - This option enables the hardware independent IEEE 802.11 - networking stack. - -menu "Rate control algorithm selection" - depends on MAC80211 != n - -choice - prompt "Default rate control algorithm" - default MAC80211_RC_DEFAULT_PID - ---help--- - This option selects the default rate control algorithm - mac80211 will use. Note that this default can still be - overriden through the ieee80211_default_rc_algo module - parameter if different algorithms are available. - -config MAC80211_RC_DEFAULT_PID - bool "PID controller based rate control algorithm" - select MAC80211_RC_PID - ---help--- - Select the PID controller based rate control as the - default rate control algorithm. You should choose - this unless you know what you are doing. - -config MAC80211_RC_DEFAULT_SIMPLE - bool "Simple rate control algorithm" - select MAC80211_RC_SIMPLE - ---help--- - Select the simple rate control as the default rate - control algorithm. Note that this is a non-responsive, - dumb algorithm. You should choose the PID rate control - instead. - -config MAC80211_RC_DEFAULT_NONE - bool "No default algorithm" - depends on EMBEDDED - help - Selecting this option will select no default algorithm - and allow you to not build any. Do not choose this - option unless you know your driver comes with another - suitable algorithm. -endchoice - -comment "Selecting 'y' for an algorithm will" -comment "build the algorithm into mac80211." - -config MAC80211_RC_DEFAULT - string - default "pid" if MAC80211_RC_DEFAULT_PID - default "simple" if MAC80211_RC_DEFAULT_SIMPLE - default "" - -config MAC80211_RC_PID - tristate "PID controller based rate control algorithm" - ---help--- - This option enables a TX rate control algorithm for - mac80211 that uses a PID controller to select the TX - rate. - - Say Y or M unless you're sure you want to use a - different rate control algorithm. - -config MAC80211_RC_SIMPLE - tristate "Simple rate control algorithm (DEPRECATED)" - ---help--- - This option enables a very simple, non-responsive TX - rate control algorithm. This algorithm is deprecated - and will be removed from the kernel in the near future. - It has been replaced by the PID algorithm. - - Say N unless you know what you are doing. -endmenu - -config MAC80211_LEDS - bool "Enable LED triggers" - depends on MAC80211 && LEDS_TRIGGERS - ---help--- - This option enables a few LED triggers for different - packet receive/transmit events. - -config MAC80211_DEBUGFS - bool "Export mac80211 internals in DebugFS" - depends on MAC80211 && DEBUG_FS - ---help--- - Select this to see extensive information about - the internal state of mac80211 in debugfs. - - Say N unless you know you need this. - -config MAC80211_DEBUG_PACKET_ALIGNMENT - bool "Enable packet alignment debugging" - depends on MAC80211 - help - This option is recommended for driver authors and strongly - discouraged for everybody else, it will trigger a warning - when a driver hands mac80211 a buffer that is aligned in - a way that will cause problems with the IP stack on some - architectures. - - Say N unless you're writing a mac80211 based driver. - -config MAC80211_DEBUG - bool "Enable debugging output" - depends on MAC80211 - ---help--- - This option will enable debug tracing output for the - ieee80211 network stack. - - If you are not trying to debug or develop the ieee80211 - subsystem, you most likely want to say N here. - -config MAC80211_HT_DEBUG - bool "Enable HT debugging output" - depends on MAC80211_DEBUG - ---help--- - This option enables 802.11n High Throughput features - debug tracing output. - - If you are not trying to debug of develop the ieee80211 - subsystem, you most likely want to say N here. - -config MAC80211_VERBOSE_DEBUG - bool "Verbose debugging output" - depends on MAC80211_DEBUG - -config MAC80211_LOWTX_FRAME_DUMP - bool "Debug frame dumping" - depends on MAC80211_DEBUG - ---help--- - Selecting this option will cause the stack to - print a message for each frame that is handed - to the lowlevel driver for transmission. This - message includes all MAC addresses and the - frame control field. - - If unsure, say N and insert the debugging code - you require into the driver you are debugging. - -config TKIP_DEBUG - bool "TKIP debugging" - depends on MAC80211_DEBUG - -config MAC80211_DEBUG_COUNTERS - bool "Extra statistics for TX/RX debugging" - depends on MAC80211_DEBUG - -config MAC80211_IBSS_DEBUG - bool "Support for IBSS testing" - depends on MAC80211_DEBUG - ---help--- - Say Y here if you intend to debug the IBSS code. - -config MAC80211_VERBOSE_PS_DEBUG - bool "Verbose powersave mode debugging" - depends on MAC80211_DEBUG - ---help--- - Say Y here to print out verbose powersave - mode debug messages. |