ipq806x: update target to v3.18

Patches in the ipq806x/patches folder were out of tree in v3.14. The
newest patch at the time was from June, so we can safely assume that
either the patches have been merged, or they have been rejected for
a good reason. If patches are seen missing, we'll cherry-pick them
on a per-needed basis.

This new kernel have been tested on AP148, which seems to works fine.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44386

1 files changed, 0 insertions, 125 deletions

diff --git a/target/linux/ipq806x/patches/0158-usb-dwc3-qcom-Add-device-tree-binding.patch b/target/linux/ipq806x/patches/0158-usb-dwc3-qcom-Add-device-tree-binding.patch
deleted file mode 100644
index ffe2a8d597..0000000000
--- a/target/linux/ipq806x/patches/0158-usb-dwc3-qcom-Add-device-tree-binding.patch
+++ /dev/null
@@ -1,125 +0,0 @@
-From c7045330c5976eb31bd79bc57c5db684588d595e Mon Sep 17 00:00:00 2001
-From: "Ivan T. Ivanov" <iivanov@mm-sol.com>
-Date: Mon, 7 Oct 2013 10:44:55 +0300
-Subject: [PATCH 158/182] usb: dwc3: qcom: Add device tree binding
-
-QCOM USB3.0 core wrapper consist of USB3.0 IP from Synopsys
-(SNPS) and HS, SS PHY's control and configuration registers.
-
-It could operate in device mode (SS, HS, FS) and host
-mode (SS, HS, FS, LS).
-
-Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
-Acked-by: Stephen Warren <swarren@nvidia.com>
----
- .../devicetree/bindings/usb/qcom,dwc3.txt          |  104 ++++++++++++++++++++
- 1 file changed, 104 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.txt
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
-@@ -0,0 +1,104 @@
-+Qualcomm SuperSpeed DWC3 USB SoC controller
-+
-+
-+QCOM DWC3 Highspeed USB PHY
-+========================
-+Required properities:
-+- compatible:	should contain "qcom,dwc3-hsphy";
-+- reg:			offset and length of the register set in the memory map
-+- clocks:		A list of phandle + clock-specifier pairs for the
-+				clocks listed in clock-names
-+- clock-names:	Should contain the following:
-+  "utmi"		UTMI clock
-+- v1p8-supply:	phandle to the regulator for the 1.8v supply to HSPHY.
-+- v3p3-supply:	phandle to the regulator for the 3.3v supply to HSPHY.
-+- vbus-supply:	phandle to the regulator for the vbus supply for host
-+		mode.
-+- vddcx-supply: phandle to the regulator for the vdd supply for HSPHY
-+                digital circuit operation.
-+
-+Optional clocks:
-+  "xo"			External reference clock
-+
-+
-+QCOM DWC3 Superspeed USB PHY
-+=========================
-+Required properities:
-+- compatible:	should contain "qcom,dwc3-ssphy";
-+- reg:			offset and length of the register set in the memory map
-+- clocks:		A list of phandle + clock-specifier pairs for the
-+				clocks listed in clock-names
-+- clock-names:	Should contain the following:
-+  "ref"			Reference clock used in host mode.
-+- v1p8-supply:	phandle to the regulator for the 1.8v supply to HSPHY.
-+- vddcx-supply: phandle to the regulator for the vdd supply for HSPHY
-+                digital circuit operation.
-+
-+Optional clocks:
-+  "xo"			External reference clock
-+
-+QCOM DWC3 controller wrapper
-+===========================
-+Required properties:
-+- compatible:	should contain "qcom,dwc3"
-+- clocks:		A list of phandle + clock-specifier pairs for the
-+				clocks listed in clock-names
-+- clock-names:	Should contain the following:
-+  "core"		Master/Core clock, have to be >= 125 MHz for SS
-+				operation and >= 60MHz for HS operation
-+
-+Optional clocks:
-+  "iface"		System bus AXI clock.  Not present on all platforms
-+  "sleep"		Sleep clock, used when USB3 core goes into low
-+				power mode (U3).
-+
-+Optional regulator:
-+- gdsc-supply:	phandle to the regulator from globally distributed
-+				switch controller
-+
-+Required child node:
-+A child node must exist to represent the core DWC3 IP block. The name of
-+the node is not important. The content of the node is defined in dwc3.txt.
-+
-+Example device nodes:
-+
-+		hs_phy_0: phy@110f8800 {
-+			compatible = "qcom,dwc3-hsphy";
-+			reg = <0x110f8800 0x30>;
-+			clocks = <&gcc USB30_0_UTMI_CLK>;
-+			clock-names = "utmi";
-+
-+			status = "disabled";
-+		};
-+
-+		ss_phy_0: phy@110f8830 {
-+			compatible = "qcom,dwc3-ssphy";
-+			reg = <0x110f8830 0x30>;
-+
-+			clocks = <&gcc USB30_0_MASTER_CLK>;
-+			clock-names = "ref";
-+
-+			status = "disabled";
-+		};
-+
-+		usb3_0: usb30@0 {
-+			compatible = "qcom,dwc3";
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+			clocks = <&gcc USB30_0_MASTER_CLK>;
-+			clock-names = "core";
-+
-+			ranges;
-+
-+			status = "disabled";
-+
-+			dwc3@11000000 {
-+				compatible = "snps,dwc3";
-+				reg = <0x11000000 0xcd00>;
-+				interrupts = <0 110 0x4>;
-+				usb-phy = <&hs_phy_0>, <&ss_phy_0>;
-+				phy-names = "usb2-phy", "usb3-phy";
-+				tx-fifo-resize;
-+				dr_mode = "host";
-+			};
-+		};