(6/6) bcm57xx: package

This is the bcm57xx package.  I have tested default vlan functions,
but I dont have the equipment to test more advanced setups.  The default
vlan setup seems to be working fine.  I also added the activate_gpio
parameter which will make the driver activate the switch via gpio before
probing for it.

I'm not sure which method is best for autoload.  For the wrt350n, I
need the activate_gpio parameter.  But its probably not a good idea
to add that to the autoload file.  On a system without a bcm57xx switch,
isn't it a bad idea to mess with the gpios looking for the switch? Ideally,
wouldn't it be best to load the bcm57xx module from broadcom-diag, after
it has determined which router its on?  I tried using 'request_module' from
there, but had no success.  For now, I am relying on preinit to load
the bcm57xx module with activate_gpio param, after it has failed to load
switch_robo and switch_adm.

Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>

SVN-Revision: 11471

1 files changed, 70 insertions, 0 deletions

diff --git a/package/broadcom-57xx/src/bcmrobo.h b/package/broadcom-57xx/src/bcmrobo.h
new file mode 100644
index 0000000000..ce9659bba0
--- /dev/null
+++ b/package/broadcom-57xx/src/bcmrobo.h
@@ -0,0 +1,70 @@
+/*
+ * RoboSwitch setup functions
+ *
+ * Copyright 2007, Broadcom Corporation
+ * All Rights Reserved.
+ * 
+ * THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
+ * KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
+ * SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
+ *
+ * $Id: bcmrobo.h,v 1.1.1.6 2007/05/31 08:00:41 michael Exp $
+ */
+
+#ifndef _bcm_robo_h_
+#define _bcm_robo_h_
+#include <switch-core.h>
+
+#define DEVID5325   0x25    /* 5325 (Not really be we fake it) */
+
+/* Forward declaration */
+typedef struct robo_info_s robo_info_t;
+
+/* Device access/config oprands */
+typedef struct {
+	/* low level routines */
+	void (*enable_mgmtif)(robo_info_t *robo);	/* enable mgmt i/f, optional */
+	void (*disable_mgmtif)(robo_info_t *robo);	/* disable mgmt i/f, optional */
+	int (*write_reg)(robo_info_t *robo, uint8 page, uint8 reg, void *val, int len);
+	int (*read_reg)(robo_info_t *robo, uint8 page, uint8 reg, void *val, int len);
+	/* description */
+	char *desc;
+} dev_ops_t;
+
+
+typedef	uint16 (*miird_f)(void *h, int add, int off);
+typedef	void (*miiwr_f)(void *h, int add, int off, uint16 val);
+
+/* Private state per RoboSwitch */
+struct robo_info_s {
+	sb_t	*sbh;			/* SiliconBackplane handle */
+	char	*vars;			/* nvram variables handle */
+	void	*h;			/* dev handle */
+	uint16	devid;			/* Device id for the switch */
+	char	*name;			/* Linux device name */
+	char	macaddr[6];
+
+	dev_ops_t *ops;			/* device ops */
+	uint8	page;			/* current page */
+
+	/* SPI */
+	uint32	ss, sck, mosi, miso;	/* GPIO mapping */
+
+	/* MII */
+	miird_f	miird;
+	miiwr_f	miiwr;
+};
+
+extern robo_info_t *bcm_robo_attach(sb_t *sbh, void *h, char *name, char *vars, miird_f miird, miiwr_f miiwr);
+extern void bcm_robo_detach(robo_info_t *robo);
+extern int bcm_robo_enable_device(robo_info_t *robo);
+extern int bcm_robo_config_vlan(robo_info_t *robo, uint8 *mac_addr);
+extern int bcm_robo_enable_switch(robo_info_t *robo);
+extern void bcm_robo_set_macaddr(robo_info_t *robo, char *macaddr);
+
+#ifdef BCMDBG
+extern void robo_dump_regs(robo_info_t *robo, struct bcmstrbuf *b);
+#endif /* BCMDBG */
+
+#endif /* _bcm_robo_h_ */