!!omap
- ADC0_CR:
    fields: !!omap
    - SEL:
        access: rw
        description: Selects which of the ADCn_[7:0] inputs are to be sampled and
          converted
        lsb: 0
        reset_value: '0'
        width: 8
    - CLKDIV:
        access: rw
        description: The ADC clock is divided by the CLKDIV value plus one to produce
          the clock for the A/D converter
        lsb: 8
        reset_value: '0'
        width: 8
    - BURST:
        access: rw
        description: Controls Burst mode
        lsb: 16
        reset_value: '0'
        width: 1
    - CLKS:
        access: rw
        description: This field selects the number of clocks used for each conversion
          in Burst mode and the number of bits of accuracy of the result in the LS
          bits of ADDR, between 11 clocks (10 bits) and 4 clocks (3 bits).
        lsb: 17
        reset_value: '0'
        width: 3
    - PDN:
        access: rw
        description: Power mode
        lsb: 21
        reset_value: '0'
        width: 1
    - START:
        access: rw
        description: Controls the start of an A/D conversion when the BURST bit is
          0
        lsb: 24
        reset_value: '0'
        width: 3
    - EDGE:
        access: rw
        description: Controls rising or falling edge on the selected signal for the
          start of a conversion
        lsb: 27
        reset_value: '0'
        width: 1
- ADC1_CR:
    fields: !!omap
    - SEL:
        access: rw
        description: Selects which of the ADCn_[7:0] inputs are to be sampled and
          converted
        lsb: 0
        reset_value: '0'
        width: 8
    - CLKDIV:
        access: rw
        description: The ADC clock is divided by the CLKDIV value plus one to produce
          the clock for the A/D converter
        lsb: 8
        reset_value: '0'
        width: 8
    - BURST:
        access: rw
        description: Controls Burst mode
        lsb: 16
        reset_value: '0'
        width: 1
    - CLKS:
        access: rw
        description: This field selects the number of clocks used for each conversion
          in Burst mode and the number of bits of accuracy of the result in the LS
          bits of ADDR, between 11 clocks (10 bits) and 4 clocks (3 bits).
        lsb: 17
        reset_value: '0'
        width: 3
    - PDN:
        access: rw
        description: Power mode
        lsb: 21
        reset_value: '0'
        width: 1
    - START:
        access: rw
        description: Controls the start of an A/D conversion when the BURST bit is
          0
        lsb: 24
        reset_value: '0'
        width: 3
    - EDGE:
        access: rw
        description: Controls rising or falling edge on the selected signal for the
          start of a conversion
        lsb: 27
        reset_value: '0'
        width: 1
- ADC0_GDR:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADCn pin selected by the SEL field, divided by the reference
          voltage on the VDDA pin
        lsb: 6
        reset_value: '0'
        width: 10
    - CHN:
        access: r
        description: These bits contain the channel from which the LS bits were converted
        lsb: 24
        reset_value: '0'
        width: 3
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an analog-to-digital conversion completes.
          It is cleared when this register is read and when the AD0/1CR register is
          written
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_GDR:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADCn pin selected by the SEL field, divided by the reference
          voltage on the VDDA pin
        lsb: 6
        reset_value: '0'
        width: 10
    - CHN:
        access: r
        description: These bits contain the channel from which the LS bits were converted
        lsb: 24
        reset_value: '0'
        width: 3
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an analog-to-digital conversion completes.
          It is cleared when this register is read and when the AD0/1CR register is
          written
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_INTEN:
    fields: !!omap
    - ADINTEN:
        access: rw
        description: These bits allow control over which A/D channels generate interrupts
          for conversion completion
        lsb: 0
        reset_value: '0'
        width: 8
    - ADGINTEN:
        access: rw
        description: When 1, enables the global DONE flag in ADDR to generate an interrupt.
          When 0, only the individual A/D channels enabled by ADINTEN 7:0 will generate
          interrupts.
        lsb: 8
        reset_value: '1'
        width: 1
- ADC1_INTEN:
    fields: !!omap
    - ADINTEN:
        access: rw
        description: These bits allow control over which A/D channels generate interrupts
          for conversion completion
        lsb: 0
        reset_value: '0'
        width: 8
    - ADGINTEN:
        access: rw
        description: When 1, enables the global DONE flag in ADDR to generate an interrupt.
          When 0, only the individual A/D channels enabled by ADINTEN 7:0 will generate
          interrupts.
        lsb: 8
        reset_value: '1'
        width: 1
- ADC0_DR0:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC0 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR0:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC0 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR1:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC1 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR1:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC1 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR2:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC2 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR2:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC2 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR3:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC3 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR3:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC3 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR4:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC4 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR4:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC4 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR5:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC5 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR5:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC5 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR6:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC6 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR6:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC6 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_DR7:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC7 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC1_DR7:
    fields: !!omap
    - V_VREF:
        access: r
        description: When DONE is 1, this field contains a binary fraction representing
          the voltage on the ADC7 pin divided by the reference voltage on the VDDA
          pin
        lsb: 6
        reset_value: '0'
        width: 10
    - OVERRUN:
        access: r
        description: This bit is 1 in burst mode if the results of one or more conversions
          was (were) lost and overwritten before the conversion that produced the
          result in the V_VREF bits in this register.
        lsb: 30
        reset_value: '0'
        width: 1
    - DONE:
        access: r
        description: This bit is set to 1 when an A/D conversion completes.
        lsb: 31
        reset_value: '0'
        width: 1
- ADC0_STAT:
    fields: !!omap
    - DONE:
        access: r
        description: These bits mirror the DONE status flags that appear in the result
          register for each A/D channel.
        lsb: 0
        reset_value: '0'
        width: 8
    - OVERRUN:
        access: r
        description: These bits mirror the OVERRRUN status flags that appear in the
          result register for each A/D channel.
        lsb: 8
        reset_value: '0'
        width: 8
    - ADINT:
        access: r
        description: This bit is the A/D interrupt flag. It is one when any of the
          individual A/D channel Done flags is asserted and enabled to contribute
          to the A/D interrupt via the ADINTEN register.
        lsb: 16
        reset_value: '0'
        width: 1