From 849369d6c66d3054688672f97d31fceb8e8230fb Mon Sep 17 00:00:00 2001 From: root Date: Fri, 25 Dec 2015 04:40:36 +0000 Subject: initial_commit --- .../video4linux/cx2341x/fw-decoder-api.txt | 297 +++++++++++++++++++++ 1 file changed, 297 insertions(+) create mode 100644 Documentation/video4linux/cx2341x/fw-decoder-api.txt (limited to 'Documentation/video4linux/cx2341x/fw-decoder-api.txt') diff --git a/Documentation/video4linux/cx2341x/fw-decoder-api.txt b/Documentation/video4linux/cx2341x/fw-decoder-api.txt new file mode 100644 index 00000000..8c317b7a --- /dev/null +++ b/Documentation/video4linux/cx2341x/fw-decoder-api.txt @@ -0,0 +1,297 @@ +Decoder firmware API description +================================ + +Note: this API is part of the decoder firmware, so it's cx23415 only. + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_PING_FW +Enum 0/0x00 +Description + This API call does nothing. It may be used to check if the firmware + is responding. + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_START_PLAYBACK +Enum 1/0x01 +Description + Begin or resume playback. +Param[0] + 0 based frame number in GOP to begin playback from. +Param[1] + Specifies the number of muted audio frames to play before normal + audio resumes. (This is not implemented in the firmware, leave at 0) + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_STOP_PLAYBACK +Enum 2/0x02 +Description + Ends playback and clears all decoder buffers. If PTS is not zero, + playback stops at specified PTS. +Param[0] + Display 0=last frame, 1=black + Note: this takes effect immediately, so if you want to wait for a PTS, + then use '0', otherwise the screen goes to black at once. + You can call this later (even if there is no playback) with a 1 value + to set the screen to black. +Param[1] + PTS low +Param[2] + PTS high + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_PLAYBACK_SPEED +Enum 3/0x03 +Description + Playback stream at speed other than normal. There are two modes of + operation: + Smooth: host transfers entire stream and firmware drops unused + frames. + Coarse: host drops frames based on indexing as required to achieve + desired speed. +Param[0] + Bitmap: + 0:7 0 normal + 1 fast only "1.5 times" + n nX fast, 1/nX slow + 30 Framedrop: + '0' during 1.5 times play, every other B frame is dropped + '1' during 1.5 times play, stream is unchanged (bitrate + must not exceed 8mbps) + 31 Speed: + '0' slow + '1' fast + Note: n is limited to 2. Anything higher does not result in + faster playback. Instead the host should start dropping frames. +Param[1] + Direction: 0=forward, 1=reverse + Note: to make reverse playback work you have to write full GOPs in + reverse order. +Param[2] + Picture mask: + 1=I frames + 3=I, P frames + 7=I, P, B frames +Param[3] + B frames per GOP (for reverse play only) + Note: for reverse playback the Picture Mask should be set to I or I, P. + Adding B frames to the mask will result in corrupt video. This field + has to be set to the correct value in order to keep the timing correct. +Param[4] + Mute audio: 0=disable, 1=enable +Param[5] + Display 0=frame, 1=field +Param[6] + Specifies the number of muted audio frames to play before normal audio + resumes. (Not implemented in the firmware, leave at 0) + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_STEP_VIDEO +Enum 5/0x05 +Description + Each call to this API steps the playback to the next unit defined below + in the current playback direction. +Param[0] + 0=frame, 1=top field, 2=bottom field + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_DMA_BLOCK_SIZE +Enum 8/0x08 +Description + Set DMA transfer block size. Counterpart to API 0xC9 +Param[0] + DMA transfer block size in bytes. A different size may be specified + when issuing the DMA transfer command. + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_GET_XFER_INFO +Enum 9/0x09 +Description + This API call may be used to detect an end of stream condition. +Result[0] + Stream type +Result[1] + Address offset +Result[2] + Maximum bytes to transfer +Result[3] + Buffer fullness + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_GET_DMA_STATUS +Enum 10/0x0A +Description + Status of the last DMA transfer +Result[0] + Bit 1 set means transfer complete + Bit 2 set means DMA error + Bit 3 set means linked list error +Result[1] + DMA type: 0=MPEG, 1=OSD, 2=YUV + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SCHED_DMA_FROM_HOST +Enum 11/0x0B +Description + Setup DMA from host operation. Counterpart to API 0xCC +Param[0] + Memory address of link list +Param[1] + Total # of bytes to transfer +Param[2] + DMA type (0=MPEG, 1=OSD, 2=YUV) + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_PAUSE_PLAYBACK +Enum 13/0x0D +Description + Freeze playback immediately. In this mode, when internal buffers are + full, no more data will be accepted and data request IRQs will be + masked. +Param[0] + Display: 0=last frame, 1=black + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_HALT_FW +Enum 14/0x0E +Description + The firmware is halted and no further API calls are serviced until + the firmware is uploaded again. + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_STANDARD +Enum 16/0x10 +Description + Selects display standard +Param[0] + 0=NTSC, 1=PAL + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_GET_VERSION +Enum 17/0x11 +Description + Returns decoder firmware version information +Result[0] + Version bitmask: + Bits 0:15 build + Bits 16:23 minor + Bits 24:31 major + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_STREAM_INPUT +Enum 20/0x14 +Description + Select decoder stream input port +Param[0] + 0=memory (default), 1=streaming + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_GET_TIMING_INFO +Enum 21/0x15 +Description + Returns timing information from start of playback +Result[0] + Frame count by decode order +Result[1] + Video PTS bits 0:31 by display order +Result[2] + Video PTS bit 32 by display order +Result[3] + SCR bits 0:31 by display order +Result[4] + SCR bit 32 by display order + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_AUDIO_MODE +Enum 22/0x16 +Description + Select audio mode +Param[0] + Dual mono mode action + 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged +Param[1] + Stereo mode action: + 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_EVENT_NOTIFICATION +Enum 23/0x17 +Description + Setup firmware to notify the host about a particular event. + Counterpart to API 0xD5 +Param[0] + Event: 0=Audio mode change between mono, (joint) stereo and dual channel. + Event: 3=Decoder started + Event: 4=Unknown: goes off 10-15 times per second while decoding. + Event: 5=Some sync event: goes off once per frame. +Param[1] + Notification 0=disabled, 1=enabled +Param[2] + Interrupt bit +Param[3] + Mailbox slot, -1 if no mailbox required. + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_DISPLAY_BUFFERS +Enum 24/0x18 +Description + Number of display buffers. To decode all frames in reverse playback you + must use nine buffers. +Param[0] + 0=six buffers, 1=nine buffers + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_EXTRACT_VBI +Enum 25/0x19 +Description + Extracts VBI data +Param[0] + 0=extract from extension & user data, 1=extract from private packets +Result[0] + VBI table location +Result[1] + VBI table size + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_DECODER_SOURCE +Enum 26/0x1A +Description + Selects decoder source. Ensure that the parameters passed to this + API match the encoder settings. +Param[0] + Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host +Param[1] + YUV picture width +Param[2] + YUV picture height +Param[3] + Bitmap: see Param[0] of API 0xBD + +------------------------------------------------------------------------------- + +Name CX2341X_DEC_SET_PREBUFFERING +Enum 30/0x1E +Description + Decoder prebuffering, when enabled up to 128KB are buffered for + streams <8mpbs or 640KB for streams >8mbps +Param[0] + 0=off, 1=on -- cgit v1.2.3