From 849369d6c66d3054688672f97d31fceb8e8230fb Mon Sep 17 00:00:00 2001 From: root Date: Fri, 25 Dec 2015 04:40:36 +0000 Subject: initial_commit --- Documentation/usb/callbacks.txt | 134 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 134 insertions(+) create mode 100644 Documentation/usb/callbacks.txt (limited to 'Documentation/usb/callbacks.txt') diff --git a/Documentation/usb/callbacks.txt b/Documentation/usb/callbacks.txt new file mode 100644 index 00000000..9e85846b --- /dev/null +++ b/Documentation/usb/callbacks.txt @@ -0,0 +1,134 @@ +What callbacks will usbcore do? +=============================== + +Usbcore will call into a driver through callbacks defined in the driver +structure and through the completion handler of URBs a driver submits. +Only the former are in the scope of this document. These two kinds of +callbacks are completely independent of each other. Information on the +completion callback can be found in Documentation/usb/URB.txt. + +The callbacks defined in the driver structure are: + +1. Hotplugging callbacks: + + * @probe: Called to see if the driver is willing to manage a particular + * interface on a device. + * @disconnect: Called when the interface is no longer accessible, usually + * because its device has been (or is being) disconnected or the + * driver module is being unloaded. + +2. Odd backdoor through usbfs: + + * @ioctl: Used for drivers that want to talk to userspace through + * the "usbfs" filesystem. This lets devices provide ways to + * expose information to user space regardless of where they + * do (or don't) show up otherwise in the filesystem. + +3. Power management (PM) callbacks: + + * @suspend: Called when the device is going to be suspended. + * @resume: Called when the device is being resumed. + * @reset_resume: Called when the suspended device has been reset instead + * of being resumed. + +4. Device level operations: + + * @pre_reset: Called when the device is about to be reset. + * @post_reset: Called after the device has been reset + +The ioctl interface (2) should be used only if you have a very good +reason. Sysfs is preferred these days. The PM callbacks are covered +separately in Documentation/usb/power-management.txt. + +Calling conventions +=================== + +All callbacks are mutually exclusive. There's no need for locking +against other USB callbacks. All callbacks are called from a task +context. You may sleep. However, it is important that all sleeps have a +small fixed upper limit in time. In particular you must not call out to +user space and await results. + +Hotplugging callbacks +===================== + +These callbacks are intended to associate and disassociate a driver with +an interface. A driver's bond to an interface is exclusive. + +The probe() callback +-------------------- + +int (*probe) (struct usb_interface *intf, + const struct usb_device_id *id); + +Accept or decline an interface. If you accept the device return 0, +otherwise -ENODEV or -ENXIO. Other error codes should be used only if a +genuine error occurred during initialisation which prevented a driver +from accepting a device that would else have been accepted. +You are strongly encouraged to use usbcore's facility, +usb_set_intfdata(), to associate a data structure with an interface, so +that you know which internal state and identity you associate with a +particular interface. The device will not be suspended and you may do IO +to the interface you are called for and endpoint 0 of the device. Device +initialisation that doesn't take too long is a good idea here. + +The disconnect() callback +------------------------- + +void (*disconnect) (struct usb_interface *intf); + +This callback is a signal to break any connection with an interface. +You are not allowed any IO to a device after returning from this +callback. You also may not do any other operation that may interfere +with another driver bound the interface, eg. a power management +operation. +If you are called due to a physical disconnection, all your URBs will be +killed by usbcore. Note that in this case disconnect will be called some +time after the physical disconnection. Thus your driver must be prepared +to deal with failing IO even prior to the callback. + +Device level callbacks +====================== + +pre_reset +--------- + +int (*pre_reset)(struct usb_interface *intf); + +A driver or user space is triggering a reset on the device which +contains the interface passed as an argument. Cease IO, wait for all +outstanding URBs to complete, and save any device state you need to +restore. No more URBs may be submitted until the post_reset method +is called. + +If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if you +are in atomic context. + +post_reset +---------- + +int (*post_reset)(struct usb_interface *intf); + +The reset has completed. Restore any saved device state and begin +using the device again. + +If you need to allocate memory here, use GFP_NOIO or GFP_ATOMIC, if you +are in atomic context. + +Call sequences +============== + +No callbacks other than probe will be invoked for an interface +that isn't bound to your driver. + +Probe will never be called for an interface bound to a driver. +Hence following a successful probe, disconnect will be called +before there is another probe for the same interface. + +Once your driver is bound to an interface, disconnect can be +called at any time except in between pre_reset and post_reset. +pre_reset is always followed by post_reset, even if the reset +failed or the device has been unplugged. + +suspend is always followed by one of: resume, reset_resume, or +disconnect. -- cgit v1.2.3