From 849369d6c66d3054688672f97d31fceb8e8230fb Mon Sep 17 00:00:00 2001
From: root <root@artemis.panaceas.org>
Date: Fri, 25 Dec 2015 04:40:36 +0000
Subject: initial_commit

---
 Documentation/power/swsusp-and-swap-files.txt | 60 +++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/power/swsusp-and-swap-files.txt

(limited to 'Documentation/power/swsusp-and-swap-files.txt')

diff --git a/Documentation/power/swsusp-and-swap-files.txt b/Documentation/power/swsusp-and-swap-files.txt
new file mode 100644
index 00000000..f281886d
--- /dev/null
+++ b/Documentation/power/swsusp-and-swap-files.txt
@@ -0,0 +1,60 @@
+Using swap files with software suspend (swsusp)
+	(C) 2006 Rafael J. Wysocki <rjw@sisk.pl>
+
+The Linux kernel handles swap files almost in the same way as it handles swap
+partitions and there are only two differences between these two types of swap
+areas:
+(1) swap files need not be contiguous,
+(2) the header of a swap file is not in the first block of the partition that
+holds it.  From the swsusp's point of view (1) is not a problem, because it is
+already taken care of by the swap-handling code, but (2) has to be taken into
+consideration.
+
+In principle the location of a swap file's header may be determined with the
+help of appropriate filesystem driver.  Unfortunately, however, it requires the
+filesystem holding the swap file to be mounted, and if this filesystem is
+journaled, it cannot be mounted during resume from disk.  For this reason to
+identify a swap file swsusp uses the name of the partition that holds the file
+and the offset from the beginning of the partition at which the swap file's
+header is located.  For convenience, this offset is expressed in <PAGE_SIZE>
+units.
+
+In order to use a swap file with swsusp, you need to:
+
+1) Create the swap file and make it active, eg.
+
+# dd if=/dev/zero of=<swap_file_path> bs=1024 count=<swap_file_size_in_k>
+# mkswap <swap_file_path>
+# swapon <swap_file_path>
+
+2) Use an application that will bmap the swap file with the help of the
+FIBMAP ioctl and determine the location of the file's swap header, as the
+offset, in <PAGE_SIZE> units, from the beginning of the partition which
+holds the swap file.
+
+3) Add the following parameters to the kernel command line:
+
+resume=<swap_file_partition> resume_offset=<swap_file_offset>
+
+where <swap_file_partition> is the partition on which the swap file is located
+and <swap_file_offset> is the offset of the swap header determined by the
+application in 2) (of course, this step may be carried out automatically
+by the same application that determines the swap file's header offset using the
+FIBMAP ioctl)
+
+OR
+
+Use a userland suspend application that will set the partition and offset
+with the help of the SNAPSHOT_SET_SWAP_AREA ioctl described in
+Documentation/power/userland-swsusp.txt (this is the only method to suspend
+to a swap file allowing the resume to be initiated from an initrd or initramfs
+image).
+
+Now, swsusp will use the swap file in the same way in which it would use a swap
+partition.  In particular, the swap file has to be active (ie. be present in
+/proc/swaps) so that it can be used for suspending.
+
+Note that if the swap file used for suspending is deleted and recreated,
+the location of its header need not be the same as before.  Thus every time
+this happens the value of the "resume_offset=" kernel command line parameter
+has to be updated.
-- 
cgit v1.2.3