From 849369d6c66d3054688672f97d31fceb8e8230fb Mon Sep 17 00:00:00 2001 From: root Date: Fri, 25 Dec 2015 04:40:36 +0000 Subject: initial_commit --- Documentation/misc-devices/spear-pcie-gadget.txt | 130 +++++++++++++++++++++++ 1 file changed, 130 insertions(+) create mode 100644 Documentation/misc-devices/spear-pcie-gadget.txt (limited to 'Documentation/misc-devices/spear-pcie-gadget.txt') diff --git a/Documentation/misc-devices/spear-pcie-gadget.txt b/Documentation/misc-devices/spear-pcie-gadget.txt new file mode 100644 index 00000000..02c13ef5 --- /dev/null +++ b/Documentation/misc-devices/spear-pcie-gadget.txt @@ -0,0 +1,130 @@ +Spear PCIe Gadget Driver: + +Author +============= +Pratyush Anand (pratyush.anand@st.com) + +Location +============ +driver/misc/spear13xx_pcie_gadget.c + +Supported Chip: +=================== +SPEAr1300 +SPEAr1310 + +Menuconfig option: +========================== +Device Drivers + Misc devices + PCIe gadget support for SPEAr13XX platform +purpose +=========== +This driver has several nodes which can be read/written by configfs interface. +Its main purpose is to configure selected dual mode PCIe controller as device +and then program its various registers to configure it as a particular device +type. This driver can be used to show spear's PCIe device capability. + +Description of different nodes: +================================= + +read behavior of nodes: +------------------------------ +link :gives ltssm status. +int_type :type of supported interrupt +no_of_msi :zero if MSI is not enabled by host. A positive value is the + number of MSI vector granted. +vendor_id :returns programmed vendor id (hex) +device_id :returns programmed device id(hex) +bar0_size: :returns size of bar0 in hex. +bar0_address :returns address of bar0 mapped area in hex. +bar0_rw_offset :returns offset of bar0 for which bar0_data will return value. +bar0_data :returns data at bar0_rw_offset. + +write behavior of nodes: +------------------------------ +link :write UP to enable ltsmm DOWN to disable +int_type :write interrupt type to be configured and (int_type could be + INTA, MSI or NO_INT). Select MSI only when you have programmed + no_of_msi node. +no_of_msi :number of MSI vector needed. +inta :write 1 to assert INTA and 0 to de-assert. +send_msi :write MSI vector to be sent. +vendor_id :write vendor id(hex) to be programmed. +device_id :write device id(hex) to be programmed. +bar0_size :write size of bar0 in hex. default bar0 size is 1000 (hex) + bytes. +bar0_address :write address of bar0 mapped area in hex. (default mapping of + bar0 is SYSRAM1(E0800000). Always program bar size before bar + address. Kernel might modify bar size and address for alignment, so + read back bar size and address after writing to cross check. +bar0_rw_offset :write offset of bar0 for which bar0_data will write value. +bar0_data :write data to be written at bar0_rw_offset. + +Node programming example +=========================== +Program all PCIe registers in such a way that when this device is connected +to the PCIe host, then host sees this device as 1MB RAM. +#mount -t configfs none /Config +For nth PCIe Device Controller +# cd /config/pcie_gadget.n/ +Now you have all the nodes in this directory. +program vendor id as 0x104a +# echo 104A >> vendor_id + +program device id as 0xCD80 +# echo CD80 >> device_id + +program BAR0 size as 1MB +# echo 100000 >> bar0_size + +check for programmed bar0 size +# cat bar0_size + +Program BAR0 Address as DDR (0x2100000). This is the physical address of +memory, which is to be made visible to PCIe host. Similarly any other peripheral +can also be made visible to PCIe host. E.g., if you program base address of UART +as BAR0 address then when this device will be connected to a host, it will be +visible as UART. +# echo 2100000 >> bar0_address + +program interrupt type : INTA +# echo INTA >> int_type + +go for link up now. +# echo UP >> link + +It will have to be insured that, once link up is done on gadget, then only host +is initialized and start to search PCIe devices on its port. + +/*wait till link is up*/ +# cat link +wait till it returns UP. + +To assert INTA +# echo 1 >> inta + +To de-assert INTA +# echo 0 >> inta + +if MSI is to be used as interrupt, program no of msi vector needed (say4) +# echo 4 >> no_of_msi + +select MSI as interrupt type +# echo MSI >> int_type + +go for link up now +# echo UP >> link + +wait till link is up +# cat link +An application can repetitively read this node till link is found UP. It can +sleep between two read. + +wait till msi is enabled +# cat no_of_msi +Should return 4 (number of requested MSI vector) + +to send msi vector 2 +# echo 2 >> send_msi +#cd - -- cgit v1.2.3