From 849369d6c66d3054688672f97d31fceb8e8230fb Mon Sep 17 00:00:00 2001 From: root Date: Fri, 25 Dec 2015 04:40:36 +0000 Subject: initial_commit --- Documentation/ioctl/hdio.txt | 1071 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1071 insertions(+) create mode 100644 Documentation/ioctl/hdio.txt (limited to 'Documentation/ioctl/hdio.txt') diff --git a/Documentation/ioctl/hdio.txt b/Documentation/ioctl/hdio.txt new file mode 100644 index 00000000..91a6ecba --- /dev/null +++ b/Documentation/ioctl/hdio.txt @@ -0,0 +1,1071 @@ + Summary of HDIO_ ioctl calls. + ============================ + + Edward A. Falk + + November, 2004 + +This document attempts to describe the ioctl(2) calls supported by +the HD/IDE layer. These are by-and-large implemented (as of Linux 2.6) +in drivers/ide/ide.c and drivers/block/scsi_ioctl.c + +ioctl values are listed in . As of this writing, they +are as follows: + + ioctls that pass argument pointers to user space: + + HDIO_GETGEO get device geometry + HDIO_GET_UNMASKINTR get current unmask setting + HDIO_GET_MULTCOUNT get current IDE blockmode setting + HDIO_GET_QDMA get use-qdma flag + HDIO_SET_XFER set transfer rate via proc + HDIO_OBSOLETE_IDENTITY OBSOLETE, DO NOT USE + HDIO_GET_KEEPSETTINGS get keep-settings-on-reset flag + HDIO_GET_32BIT get current io_32bit setting + HDIO_GET_NOWERR get ignore-write-error flag + HDIO_GET_DMA get use-dma flag + HDIO_GET_NICE get nice flags + HDIO_GET_IDENTITY get IDE identification info + HDIO_GET_WCACHE get write cache mode on|off + HDIO_GET_ACOUSTIC get acoustic value + HDIO_GET_ADDRESS get sector addressing mode + HDIO_GET_BUSSTATE get the bus state of the hwif + HDIO_TRISTATE_HWIF execute a channel tristate + HDIO_DRIVE_RESET execute a device reset + HDIO_DRIVE_TASKFILE execute raw taskfile + HDIO_DRIVE_TASK execute task and special drive command + HDIO_DRIVE_CMD execute a special drive command + HDIO_DRIVE_CMD_AEB HDIO_DRIVE_TASK + + ioctls that pass non-pointer values: + + HDIO_SET_MULTCOUNT change IDE blockmode + HDIO_SET_UNMASKINTR permit other irqs during I/O + HDIO_SET_KEEPSETTINGS keep ioctl settings on reset + HDIO_SET_32BIT change io_32bit flags + HDIO_SET_NOWERR change ignore-write-error flag + HDIO_SET_DMA change use-dma flag + HDIO_SET_PIO_MODE reconfig interface to new speed + HDIO_SCAN_HWIF register and (re)scan interface + HDIO_SET_NICE set nice flags + HDIO_UNREGISTER_HWIF unregister interface + HDIO_SET_WCACHE change write cache enable-disable + HDIO_SET_ACOUSTIC change acoustic behavior + HDIO_SET_BUSSTATE set the bus state of the hwif + HDIO_SET_QDMA change use-qdma flag + HDIO_SET_ADDRESS change lba addressing modes + + HDIO_SET_IDE_SCSI Set scsi emulation mode on/off + HDIO_SET_SCSI_IDE not implemented yet + + +The information that follows was determined from reading kernel source +code. It is likely that some corrections will be made over time. + + + + + + + +General: + + Unless otherwise specified, all ioctl calls return 0 on success + and -1 with errno set to an appropriate value on error. + + Unless otherwise specified, all ioctl calls return -1 and set + errno to EFAULT on a failed attempt to copy data to or from user + address space. + + Unless otherwise specified, all data structures and constants + are defined in + + + +HDIO_GETGEO get device geometry + + usage: + + struct hd_geometry geom; + ioctl(fd, HDIO_GETGEO, &geom); + + + inputs: none + + outputs: + + hd_geometry structure containing: + + heads number of heads + sectors number of sectors/track + cylinders number of cylinders, mod 65536 + start starting sector of this partition. + + + error returns: + EINVAL if the device is not a disk drive or floppy drive, + or if the user passes a null pointer + + + notes: + + Not particularly useful with modern disk drives, whose geometry + is a polite fiction anyway. Modern drives are addressed + purely by sector number nowadays (lba addressing), and the + drive geometry is an abstraction which is actually subject + to change. Currently (as of Nov 2004), the geometry values + are the "bios" values -- presumably the values the drive had + when Linux first booted. + + In addition, the cylinders field of the hd_geometry is an + unsigned short, meaning that on most architectures, this + ioctl will not return a meaningful value on drives with more + than 65535 tracks. + + The start field is unsigned long, meaning that it will not + contain a meaningful value for disks over 219 Gb in size. + + + + +HDIO_GET_UNMASKINTR get current unmask setting + + usage: + + long val; + ioctl(fd, HDIO_GET_UNMASKINTR, &val); + + inputs: none + + outputs: + The value of the drive's current unmask setting + + + +HDIO_SET_UNMASKINTR permit other irqs during I/O + + usage: + + unsigned long val; + ioctl(fd, HDIO_SET_UNMASKINTR, val); + + inputs: + New value for unmask flag + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 1] + EBUSY Controller busy + + + + +HDIO_GET_MULTCOUNT get current IDE blockmode setting + + usage: + + long val; + ioctl(fd, HDIO_GET_MULTCOUNT, &val); + + inputs: none + + outputs: + The value of the current IDE block mode setting. This + controls how many sectors the drive will transfer per + interrupt. + + + +HDIO_SET_MULTCOUNT change IDE blockmode + + usage: + + int val; + ioctl(fd, HDIO_SET_MULTCOUNT, val); + + inputs: + New value for IDE block mode setting. This controls how many + sectors the drive will transfer per interrupt. + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range supported by disk. + EBUSY Controller busy or blockmode already set. + EIO Drive did not accept new block mode. + + notes: + + Source code comments read: + + This is tightly woven into the driver->do_special cannot + touch. DON'T do it again until a total personality rewrite + is committed. + + If blockmode has already been set, this ioctl will fail with + EBUSY + + + +HDIO_GET_QDMA get use-qdma flag + + Not implemented, as of 2.6.8.1 + + + +HDIO_SET_XFER set transfer rate via proc + + Not implemented, as of 2.6.8.1 + + + +HDIO_OBSOLETE_IDENTITY OBSOLETE, DO NOT USE + + Same as HDIO_GET_IDENTITY (see below), except that it only + returns the first 142 bytes of drive identity information. + + + +HDIO_GET_IDENTITY get IDE identification info + + usage: + + unsigned char identity[512]; + ioctl(fd, HDIO_GET_IDENTITY, identity); + + inputs: none + + outputs: + + ATA drive identity information. For full description, see + the IDENTIFY DEVICE and IDENTIFY PACKET DEVICE commands in + the ATA specification. + + error returns: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + ENOMSG IDENTIFY DEVICE information not available + + notes: + + Returns information that was obtained when the drive was + probed. Some of this information is subject to change, and + this ioctl does not re-probe the drive to update the + information. + + This information is also available from /proc/ide/hdX/identify + + + +HDIO_GET_KEEPSETTINGS get keep-settings-on-reset flag + + usage: + + long val; + ioctl(fd, HDIO_GET_KEEPSETTINGS, &val); + + inputs: none + + outputs: + The value of the current "keep settings" flag + + notes: + + When set, indicates that kernel should restore settings + after a drive reset. + + + +HDIO_SET_KEEPSETTINGS keep ioctl settings on reset + + usage: + + long val; + ioctl(fd, HDIO_SET_KEEPSETTINGS, val); + + inputs: + New value for keep_settings flag + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 1] + EBUSY Controller busy + + + +HDIO_GET_32BIT get current io_32bit setting + + usage: + + long val; + ioctl(fd, HDIO_GET_32BIT, &val); + + inputs: none + + outputs: + The value of the current io_32bit setting + + notes: + + 0=16-bit, 1=32-bit, 2,3 = 32bit+sync + + + +HDIO_GET_NOWERR get ignore-write-error flag + + usage: + + long val; + ioctl(fd, HDIO_GET_NOWERR, &val); + + inputs: none + + outputs: + The value of the current ignore-write-error flag + + + +HDIO_GET_DMA get use-dma flag + + usage: + + long val; + ioctl(fd, HDIO_GET_DMA, &val); + + inputs: none + + outputs: + The value of the current use-dma flag + + + +HDIO_GET_NICE get nice flags + + usage: + + long nice; + ioctl(fd, HDIO_GET_NICE, &nice); + + inputs: none + + outputs: + + The drive's "nice" values. + + notes: + + Per-drive flags which determine when the system will give more + bandwidth to other devices sharing the same IDE bus. + See , near symbol IDE_NICE_DSC_OVERLAP. + + + + +HDIO_SET_NICE set nice flags + + usage: + + unsigned long nice; + ... + ioctl(fd, HDIO_SET_NICE, nice); + + inputs: + bitmask of nice flags. + + outputs: none + + error returns: + EACCES Access denied: requires CAP_SYS_ADMIN + EPERM Flags other than DSC_OVERLAP and NICE_1 set. + EPERM DSC_OVERLAP specified but not supported by drive + + notes: + + This ioctl sets the DSC_OVERLAP and NICE_1 flags from values + provided by the user. + + Nice flags are listed in , starting with + IDE_NICE_DSC_OVERLAP. These values represent shifts. + + + + + +HDIO_GET_WCACHE get write cache mode on|off + + usage: + + long val; + ioctl(fd, HDIO_GET_WCACHE, &val); + + inputs: none + + outputs: + The value of the current write cache mode + + + +HDIO_GET_ACOUSTIC get acoustic value + + usage: + + long val; + ioctl(fd, HDIO_GET_ACOUSTIC, &val); + + inputs: none + + outputs: + The value of the current acoustic settings + + notes: + + See HDIO_SET_ACOUSTIC + + + +HDIO_GET_ADDRESS + + usage: + + long val; + ioctl(fd, HDIO_GET_ADDRESS, &val); + + inputs: none + + outputs: + The value of the current addressing mode: + 0 = 28-bit + 1 = 48-bit + 2 = 48-bit doing 28-bit + 3 = 64-bit + + + +HDIO_GET_BUSSTATE get the bus state of the hwif + + usage: + + long state; + ioctl(fd, HDIO_SCAN_HWIF, &state); + + inputs: none + + outputs: + Current power state of the IDE bus. One of BUSSTATE_OFF, + BUSSTATE_ON, or BUSSTATE_TRISTATE + + error returns: + EACCES Access denied: requires CAP_SYS_ADMIN + + + + +HDIO_SET_BUSSTATE set the bus state of the hwif + + usage: + + int state; + ... + ioctl(fd, HDIO_SCAN_HWIF, state); + + inputs: + Desired IDE power state. One of BUSSTATE_OFF, BUSSTATE_ON, + or BUSSTATE_TRISTATE + + outputs: none + + error returns: + EACCES Access denied: requires CAP_SYS_RAWIO + EOPNOTSUPP Hardware interface does not support bus power control + + + + +HDIO_TRISTATE_HWIF execute a channel tristate + + Not implemented, as of 2.6.8.1. See HDIO_SET_BUSSTATE + + + +HDIO_DRIVE_RESET execute a device reset + + usage: + + int args[3] + ... + ioctl(fd, HDIO_DRIVE_RESET, args); + + inputs: none + + outputs: none + + error returns: + EACCES Access denied: requires CAP_SYS_ADMIN + ENXIO No such device: phy dead or ctl_addr == 0 + EIO I/O error: reset timed out or hardware error + + notes: + + Execute a reset on the device as soon as the current IO + operation has completed. + + Executes an ATAPI soft reset if applicable, otherwise + executes an ATA soft reset on the controller. + + + +HDIO_DRIVE_TASKFILE execute raw taskfile + + Note: If you don't have a copy of the ANSI ATA specification + handy, you should probably ignore this ioctl. + + Execute an ATA disk command directly by writing the "taskfile" + registers of the drive. Requires ADMIN and RAWIO access + privileges. + + usage: + + struct { + ide_task_request_t req_task; + u8 outbuf[OUTPUT_SIZE]; + u8 inbuf[INPUT_SIZE]; + } task; + memset(&task.req_task, 0, sizeof(task.req_task)); + task.req_task.out_size = sizeof(task.outbuf); + task.req_task.in_size = sizeof(task.inbuf); + ... + ioctl(fd, HDIO_DRIVE_TASKFILE, &task); + ... + + inputs: + + (See below for details on memory area passed to ioctl.) + + io_ports[8] values to be written to taskfile registers + hob_ports[8] high-order bytes, for extended commands. + out_flags flags indicating which registers are valid + in_flags flags indicating which registers should be returned + data_phase see below + req_cmd command type to be executed + out_size size of output buffer + outbuf buffer of data to be transmitted to disk + inbuf buffer of data to be received from disk (see [1]) + + outputs: + + io_ports[] values returned in the taskfile registers + hob_ports[] high-order bytes, for extended commands. + out_flags flags indicating which registers are valid (see [2]) + in_flags flags indicating which registers should be returned + outbuf buffer of data to be transmitted to disk (see [1]) + inbuf buffer of data to be received from disk + + error returns: + EACCES CAP_SYS_ADMIN or CAP_SYS_RAWIO privilege not set. + ENOMSG Device is not a disk drive. + ENOMEM Unable to allocate memory for task + EFAULT req_cmd == TASKFILE_IN_OUT (not implemented as of 2.6.8) + EPERM req_cmd == TASKFILE_MULTI_OUT and drive + multi-count not yet set. + EIO Drive failed the command. + + notes: + + [1] READ THE FOLLOWING NOTES *CAREFULLY*. THIS IOCTL IS + FULL OF GOTCHAS. Extreme caution should be used with using + this ioctl. A mistake can easily corrupt data or hang the + system. + + [2] Both the input and output buffers are copied from the + user and written back to the user, even when not used. + + [3] If one or more bits are set in out_flags and in_flags is + zero, the following values are used for in_flags.all and + written back into in_flags on completion. + + * IDE_TASKFILE_STD_IN_FLAGS | (IDE_HOB_STD_IN_FLAGS << 8) + if LBA48 addressing is enabled for the drive + * IDE_TASKFILE_STD_IN_FLAGS + if CHS/LBA28 + + The association between in_flags.all and each enable + bitfield flips depending on endianess; fortunately, TASKFILE + only uses inflags.b.data bit and ignores all other bits. + The end result is that, on any endian machines, it has no + effect other than modifying in_flags on completion. + + [4] The default value of SELECT is (0xa0|DEV_bit|LBA_bit) + except for four drives per port chipsets. For four drives + per port chipsets, it's (0xa0|DEV_bit|LBA_bit) for the first + pair and (0x80|DEV_bit|LBA_bit) for the second pair. + + [5] The argument to the ioctl is a pointer to a region of + memory containing a ide_task_request_t structure, followed + by an optional buffer of data to be transmitted to the + drive, followed by an optional buffer to receive data from + the drive. + + Command is passed to the disk drive via the ide_task_request_t + structure, which contains these fields: + + io_ports[8] values for the taskfile registers + hob_ports[8] high-order bytes, for extended commands + out_flags flags indicating which entries in the + io_ports[] and hob_ports[] arrays + contain valid values. Type ide_reg_valid_t. + in_flags flags indicating which entries in the + io_ports[] and hob_ports[] arrays + are expected to contain valid values + on return. + data_phase See below + req_cmd Command type, see below + out_size output (user->drive) buffer size, bytes + in_size input (drive->user) buffer size, bytes + + When out_flags is zero, the following registers are loaded. + + HOB_FEATURE If the drive supports LBA48 + HOB_NSECTOR If the drive supports LBA48 + HOB_SECTOR If the drive supports LBA48 + HOB_LCYL If the drive supports LBA48 + HOB_HCYL If the drive supports LBA48 + FEATURE + NSECTOR + SECTOR + LCYL + HCYL + SELECT First, masked with 0xE0 if LBA48, 0xEF + otherwise; then, or'ed with the default + value of SELECT. + + If any bit in out_flags is set, the following registers are loaded. + + HOB_DATA If out_flags.b.data is set. HOB_DATA will + travel on DD8-DD15 on little endian machines + and on DD0-DD7 on big endian machines. + DATA If out_flags.b.data is set. DATA will + travel on DD0-DD7 on little endian machines + and on DD8-DD15 on big endian machines. + HOB_NSECTOR If out_flags.b.nsector_hob is set + HOB_SECTOR If out_flags.b.sector_hob is set + HOB_LCYL If out_flags.b.lcyl_hob is set + HOB_HCYL If out_flags.b.hcyl_hob is set + FEATURE If out_flags.b.feature is set + NSECTOR If out_flags.b.nsector is set + SECTOR If out_flags.b.sector is set + LCYL If out_flags.b.lcyl is set + HCYL If out_flags.b.hcyl is set + SELECT Or'ed with the default value of SELECT and + loaded regardless of out_flags.b.select. + + Taskfile registers are read back from the drive into + {io|hob}_ports[] after the command completes iff one of the + following conditions is met; otherwise, the original values + will be written back, unchanged. + + 1. The drive fails the command (EIO). + 2. One or more than one bits are set in out_flags. + 3. The requested data_phase is TASKFILE_NO_DATA. + + HOB_DATA If in_flags.b.data is set. It will contain + DD8-DD15 on little endian machines and + DD0-DD7 on big endian machines. + DATA If in_flags.b.data is set. It will contain + DD0-DD7 on little endian machines and + DD8-DD15 on big endian machines. + HOB_FEATURE If the drive supports LBA48 + HOB_NSECTOR If the drive supports LBA48 + HOB_SECTOR If the drive supports LBA48 + HOB_LCYL If the drive supports LBA48 + HOB_HCYL If the drive supports LBA48 + NSECTOR + SECTOR + LCYL + HCYL + + The data_phase field describes the data transfer to be + performed. Value is one of: + + TASKFILE_IN + TASKFILE_MULTI_IN + TASKFILE_OUT + TASKFILE_MULTI_OUT + TASKFILE_IN_OUT + TASKFILE_IN_DMA + TASKFILE_IN_DMAQ == IN_DMA (queueing not supported) + TASKFILE_OUT_DMA + TASKFILE_OUT_DMAQ == OUT_DMA (queueing not supported) + TASKFILE_P_IN unimplemented + TASKFILE_P_IN_DMA unimplemented + TASKFILE_P_IN_DMAQ unimplemented + TASKFILE_P_OUT unimplemented + TASKFILE_P_OUT_DMA unimplemented + TASKFILE_P_OUT_DMAQ unimplemented + + The req_cmd field classifies the command type. It may be + one of: + + IDE_DRIVE_TASK_NO_DATA + IDE_DRIVE_TASK_SET_XFER unimplemented + IDE_DRIVE_TASK_IN + IDE_DRIVE_TASK_OUT unimplemented + IDE_DRIVE_TASK_RAW_WRITE + + [6] Do not access {in|out}_flags->all except for resetting + all the bits. Always access individual bit fields. ->all + value will flip depending on endianess. For the same + reason, do not use IDE_{TASKFILE|HOB}_STD_{OUT|IN}_FLAGS + constants defined in hdreg.h. + + + +HDIO_DRIVE_CMD execute a special drive command + + Note: If you don't have a copy of the ANSI ATA specification + handy, you should probably ignore this ioctl. + + usage: + + u8 args[4+XFER_SIZE]; + ... + ioctl(fd, HDIO_DRIVE_CMD, args); + + inputs: + + Commands other than WIN_SMART + args[0] COMMAND + args[1] NSECTOR + args[2] FEATURE + args[3] NSECTOR + + WIN_SMART + args[0] COMMAND + args[1] SECTOR + args[2] FEATURE + args[3] NSECTOR + + outputs: + + args[] buffer is filled with register values followed by any + data returned by the disk. + args[0] status + args[1] error + args[2] NSECTOR + args[3] undefined + args[4+] NSECTOR * 512 bytes of data returned by the command. + + error returns: + EACCES Access denied: requires CAP_SYS_RAWIO + ENOMEM Unable to allocate memory for task + EIO Drive reports error + + notes: + + [1] For commands other than WIN_SMART, args[1] should equal + args[3]. SECTOR, LCYL and HCYL are undefined. For + WIN_SMART, 0x4f and 0xc2 are loaded into LCYL and HCYL + respectively. In both cases SELECT will contain the default + value for the drive. Please refer to HDIO_DRIVE_TASKFILE + notes for the default value of SELECT. + + [2] If NSECTOR value is greater than zero and the drive sets + DRQ when interrupting for the command, NSECTOR * 512 bytes + are read from the device into the area following NSECTOR. + In the above example, the area would be + args[4..4+XFER_SIZE]. 16bit PIO is used regardless of + HDIO_SET_32BIT setting. + + [3] If COMMAND == WIN_SETFEATURES && FEATURE == SETFEATURES_XFER + && NSECTOR >= XFER_SW_DMA_0 && the drive supports any DMA + mode, IDE driver will try to tune the transfer mode of the + drive accordingly. + + + +HDIO_DRIVE_TASK execute task and special drive command + + Note: If you don't have a copy of the ANSI ATA specification + handy, you should probably ignore this ioctl. + + usage: + + u8 args[7]; + ... + ioctl(fd, HDIO_DRIVE_TASK, args); + + inputs: + + Taskfile register values: + args[0] COMMAND + args[1] FEATURE + args[2] NSECTOR + args[3] SECTOR + args[4] LCYL + args[5] HCYL + args[6] SELECT + + outputs: + + Taskfile register values: + args[0] status + args[1] error + args[2] NSECTOR + args[3] SECTOR + args[4] LCYL + args[5] HCYL + args[6] SELECT + + error returns: + EACCES Access denied: requires CAP_SYS_RAWIO + ENOMEM Unable to allocate memory for task + ENOMSG Device is not a disk drive. + EIO Drive failed the command. + + notes: + + [1] DEV bit (0x10) of SELECT register is ignored and the + appropriate value for the drive is used. All other bits + are used unaltered. + + + +HDIO_DRIVE_CMD_AEB HDIO_DRIVE_TASK + + Not implemented, as of 2.6.8.1 + + + +HDIO_SET_32BIT change io_32bit flags + + usage: + + int val; + ioctl(fd, HDIO_SET_32BIT, val); + + inputs: + New value for io_32bit flag + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 3] + EBUSY Controller busy + + + + +HDIO_SET_NOWERR change ignore-write-error flag + + usage: + + int val; + ioctl(fd, HDIO_SET_NOWERR, val); + + inputs: + New value for ignore-write-error flag. Used for ignoring + WRERR_STAT + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 1] + EBUSY Controller busy + + + +HDIO_SET_DMA change use-dma flag + + usage: + + long val; + ioctl(fd, HDIO_SET_DMA, val); + + inputs: + New value for use-dma flag + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 1] + EBUSY Controller busy + + + +HDIO_SET_PIO_MODE reconfig interface to new speed + + usage: + + long val; + ioctl(fd, HDIO_SET_PIO_MODE, val); + + inputs: + New interface speed. + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 255] + EBUSY Controller busy + + + +HDIO_SCAN_HWIF register and (re)scan interface + + usage: + + int args[3] + ... + ioctl(fd, HDIO_SCAN_HWIF, args); + + inputs: + args[0] io address to probe + args[1] control address to probe + args[2] irq number + + outputs: none + + error returns: + EACCES Access denied: requires CAP_SYS_RAWIO + EIO Probe failed. + + notes: + + This ioctl initializes the addresses and irq for a disk + controller, probes for drives, and creates /proc/ide + interfaces as appropriate. + + + +HDIO_UNREGISTER_HWIF unregister interface + + usage: + + int index; + ioctl(fd, HDIO_UNREGISTER_HWIF, index); + + inputs: + index index of hardware interface to unregister + + outputs: none + + error returns: + EACCES Access denied: requires CAP_SYS_RAWIO + + notes: + + This ioctl removes a hardware interface from the kernel. + + Currently (2.6.8) this ioctl silently fails if any drive on + the interface is busy. + + + +HDIO_SET_WCACHE change write cache enable-disable + + usage: + + int val; + ioctl(fd, HDIO_SET_WCACHE, val); + + inputs: + New value for write cache enable + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 1] + EBUSY Controller busy + + + +HDIO_SET_ACOUSTIC change acoustic behavior + + usage: + + int val; + ioctl(fd, HDIO_SET_ACOUSTIC, val); + + inputs: + New value for drive acoustic settings + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 254] + EBUSY Controller busy + + + +HDIO_SET_QDMA change use-qdma flag + + Not implemented, as of 2.6.8.1 + + + +HDIO_SET_ADDRESS change lba addressing modes + + usage: + + int val; + ioctl(fd, HDIO_SET_ADDRESS, val); + + inputs: + New value for addressing mode + 0 = 28-bit + 1 = 48-bit + 2 = 48-bit doing 28-bit + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 2] + EBUSY Controller busy + EIO Drive does not support lba48 mode. + + +HDIO_SET_IDE_SCSI + + usage: + + long val; + ioctl(fd, HDIO_SET_IDE_SCSI, val); + + inputs: + New value for scsi emulation mode (?) + + outputs: none + + error return: + EINVAL (bdev != bdev->bd_contains) (not sure what this means) + EACCES Access denied: requires CAP_SYS_ADMIN + EINVAL value out of range [0 1] + EBUSY Controller busy + + + +HDIO_SET_SCSI_IDE + + Not implemented, as of 2.6.8.1 + + -- cgit v1.2.3