From 849369d6c66d3054688672f97d31fceb8e8230fb Mon Sep 17 00:00:00 2001 From: root Date: Fri, 25 Dec 2015 04:40:36 +0000 Subject: initial_commit --- .../bindings/powerpc/fsl/cpm_qe/qe/ucc.txt | 70 ++++++++++++++++++++++ 1 file changed, 70 insertions(+) create mode 100644 Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt (limited to 'Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt') diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 00000000..e47734be --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,70 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- device_type : should be "network", "hldc", "uart", "transparent" + "bisync", "atm", or "serial". +- compatible : could be "ucc_geth" or "fsl_atm" and so on. +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- interrupts : where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- pio-handle : The phandle for the Parallel I/O port configuration. +- port-number : for UART drivers, the port number to use, between 0 and 3. + This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. + The port number is added to the minor number of the device. Unlike the + CPM UART driver, the port-number is required for the QE UART driver. +- soft-uart : for UART drivers, if specified this means the QE UART device + driver should use "Soft-UART" mode, which is needed on some SOCs that have + broken UART hardware. Soft-UART is provided via a microcode upload. +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. + +Required properties for network device_type: +- mac-address : list of bytes representing the ethernet address. +- phy-handle : The phandle for the PHY connected to this controller. + +Recommended properties: +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = ; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; -- cgit v1.2.3