diff options
Diffstat (limited to 'Documentation/networking/ixgbe.txt')
| -rw-r--r-- | Documentation/networking/ixgbe.txt | 260 |
1 files changed, 260 insertions, 0 deletions
diff --git a/Documentation/networking/ixgbe.txt b/Documentation/networking/ixgbe.txt new file mode 100644 index 00000000..af77ed3c --- /dev/null +++ b/Documentation/networking/ixgbe.txt @@ -0,0 +1,260 @@ +Linux Base Driver for 10 Gigabit PCI Express Intel(R) Network Connection +======================================================================== + +Intel Gigabit Linux driver. +Copyright(c) 1999 - 2010 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Additional Configurations +- Performance Tuning +- Known Issues +- Support + +Identifying Your Adapter +======================== + +The driver in this release is compatible with 82598 and 82599-based Intel +Network Connections. + +For more information on how to identify your adapter, go to the Adapter & +Driver ID Guide at: + + http://support.intel.com/support/network/sb/CS-012904.htm + +SFP+ Devices with Pluggable Optics +---------------------------------- + +82599-BASED ADAPTERS + +NOTES: If your 82599-based Intel(R) Network Adapter came with Intel optics, or +is an Intel(R) Ethernet Server Adapter X520-2, then it only supports Intel +optics and/or the direct attach cables listed below. + +When 82599-based SFP+ devices are connected back to back, they should be set to +the same Speed setting via ethtool. Results may vary if you mix speed settings. +82598-based adapters support all passive direct attach cables that comply +with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach +cables are not supported. + +Supplier Type Part Numbers + +SR Modules +Intel DUAL RATE 1G/10G SFP+ SR (bailed) FTLX8571D3BCV-IT +Intel DUAL RATE 1G/10G SFP+ SR (bailed) AFBR-703SDDZ-IN1 +Intel DUAL RATE 1G/10G SFP+ SR (bailed) AFBR-703SDZ-IN2 +LR Modules +Intel DUAL RATE 1G/10G SFP+ LR (bailed) FTLX1471D3BCV-IT +Intel DUAL RATE 1G/10G SFP+ LR (bailed) AFCT-701SDDZ-IN1 +Intel DUAL RATE 1G/10G SFP+ LR (bailed) AFCT-701SDZ-IN2 + +The following is a list of 3rd party SFP+ modules and direct attach cables that +have received some testing. Not all modules are applicable to all devices. + +Supplier Type Part Numbers + +Finisar SFP+ SR bailed, 10g single rate FTLX8571D3BCL +Avago SFP+ SR bailed, 10g single rate AFBR-700SDZ +Finisar SFP+ LR bailed, 10g single rate FTLX1471D3BCL + +Finisar DUAL RATE 1G/10G SFP+ SR (No Bail) FTLX8571D3QCV-IT +Avago DUAL RATE 1G/10G SFP+ SR (No Bail) AFBR-703SDZ-IN1 +Finisar DUAL RATE 1G/10G SFP+ LR (No Bail) FTLX1471D3QCV-IT +Avago DUAL RATE 1G/10G SFP+ LR (No Bail) AFCT-701SDZ-IN1 +Finistar 1000BASE-T SFP FCLF8522P2BTL +Avago 1000BASE-T SFP ABCU-5710RZ + +82599-based adapters support all passive and active limiting direct attach +cables that comply with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. + +Laser turns off for SFP+ when ifconfig down +------------------------------------------- +"ifconfig down" turns off the laser for 82599-based SFP+ fiber adapters. +"ifconfig up" turns on the later. + + +82598-BASED ADAPTERS + +NOTES for 82598-Based Adapters: +- Intel(R) Network Adapters that support removable optical modules only support + their original module type (i.e., the Intel(R) 10 Gigabit SR Dual Port + Express Module only supports SR optical modules). If you plug in a different + type of module, the driver will not load. +- Hot Swapping/hot plugging optical modules is not supported. +- Only single speed, 10 gigabit modules are supported. +- LAN on Motherboard (LOMs) may support DA, SR, or LR modules. Other module + types are not supported. Please see your system documentation for details. + +The following is a list of 3rd party SFP+ modules and direct attach cables that +have received some testing. Not all modules are applicable to all devices. + +Supplier Type Part Numbers + +Finisar SFP+ SR bailed, 10g single rate FTLX8571D3BCL +Avago SFP+ SR bailed, 10g single rate AFBR-700SDZ +Finisar SFP+ LR bailed, 10g single rate FTLX1471D3BCL + +82598-based adapters support all passive direct attach cables that comply +with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach +cables are not supported. + + +Flow Control +------------ +Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable +receiving and transmitting pause frames for ixgbe. When TX is enabled, PAUSE +frames are generated when the receive packet buffer crosses a predefined +threshold. When rx is enabled, the transmit unit will halt for the time delay +specified when a PAUSE frame is received. + +Flow Control is enabled by default. If you want to disable a flow control +capable link partner, use ethtool: + + ethtool -A eth? autoneg off RX off TX off + +NOTE: For 82598 backplane cards entering 1 gig mode, flow control default +behavior is changed to off. Flow control in 1 gig mode on these devices can +lead to Tx hangs. + +Additional Configurations +========================= + + Jumbo Frames + ------------ + The driver supports Jumbo Frames for all adapters. Jumbo Frames support is + enabled by changing the MTU to a value larger than the default of 1500. + The maximum value for the MTU is 16110. Use the ifconfig command to + increase the MTU size. For example: + + ifconfig ethx mtu 9000 up + + The maximum MTU setting for Jumbo Frames is 16110. This value coincides + with the maximum Jumbo Frames size of 16128. + + Generic Receive Offload, aka GRO + -------------------------------- + The driver supports the in-kernel software implementation of GRO. GRO has + shown that by coalescing Rx traffic into larger chunks of data, CPU + utilization can be significantly reduced when under large Rx load. GRO is an + evolution of the previously-used LRO interface. GRO is able to coalesce + other protocols besides TCP. It's also safe to use with configurations that + are problematic for LRO, namely bridging and iSCSI. + + Data Center Bridging, aka DCB + ----------------------------- + DCB is a configuration Quality of Service implementation in hardware. + It uses the VLAN priority tag (802.1p) to filter traffic. That means + that there are 8 different priorities that traffic can be filtered into. + It also enables priority flow control which can limit or eliminate the + number of dropped packets during network stress. Bandwidth can be + allocated to each of these priorities, which is enforced at the hardware + level. + + To enable DCB support in ixgbe, you must enable the DCB netlink layer to + allow the userspace tools (see below) to communicate with the driver. + This can be found in the kernel configuration here: + + -> Networking support + -> Networking options + -> Data Center Bridging support + + Once this is selected, DCB support must be selected for ixgbe. This can + be found here: + + -> Device Drivers + -> Network device support (NETDEVICES [=y]) + -> Ethernet (10000 Mbit) (NETDEV_10000 [=y]) + -> Intel(R) 10GbE PCI Express adapters support + -> Data Center Bridging (DCB) Support + + After these options are selected, you must rebuild your kernel and your + modules. + + In order to use DCB, userspace tools must be downloaded and installed. + The dcbd tools can be found at: + + http://e1000.sf.net + + Ethtool + ------- + The driver utilizes the ethtool interface for driver configuration and + diagnostics, as well as displaying statistical information. The latest + ethtool version is required for this functionality. + + The latest release of ethtool can be found from + http://ftp.kernel.org/pub/software/network/ethtool/ + + FCoE + ---- + This release of the ixgbe driver contains new code to enable users to use + Fiber Channel over Ethernet (FCoE) and Data Center Bridging (DCB) + functionality that is supported by the 82598-based hardware. This code has + no default effect on the regular driver operation, and configuring DCB and + FCoE is outside the scope of this driver README. Refer to + http://www.open-fcoe.org/ for FCoE project information and contact + e1000-eedc@lists.sourceforge.net for DCB information. + + MAC and VLAN anti-spoofing feature + ---------------------------------- + When a malicious driver attempts to send a spoofed packet, it is dropped by + the hardware and not transmitted. An interrupt is sent to the PF driver + notifying it of the spoof attempt. + + When a spoofed packet is detected the PF driver will send the following + message to the system log (displayed by the "dmesg" command): + + Spoof event(s) detected on VF (n) + + Where n=the VF that attempted to do the spoofing. + + +Performance Tuning +================== + +An excellent article on performance tuning can be found at: + +http://www.redhat.com/promo/summit/2008/downloads/pdf/Thursday/Mark_Wagner.pdf + + +Known Issues +============ + + Enabling SR-IOV in a 32-bit Microsoft* Windows* Server 2008 Guest OS using + Intel (R) 82576-based GbE or Intel (R) 82599-based 10GbE controller under KVM + ----------------------------------------------------------------------------- + KVM Hypervisor/VMM supports direct assignment of a PCIe device to a VM. This + includes traditional PCIe devices, as well as SR-IOV-capable devices using + Intel 82576-based and 82599-based controllers. + + While direct assignment of a PCIe device or an SR-IOV Virtual Function (VF) + to a Linux-based VM running 2.6.32 or later kernel works fine, there is a + known issue with Microsoft Windows Server 2008 VM that results in a "yellow + bang" error. This problem is within the KVM VMM itself, not the Intel driver, + or the SR-IOV logic of the VMM, but rather that KVM emulates an older CPU + model for the guests, and this older CPU model does not support MSI-X + interrupts, which is a requirement for Intel SR-IOV. + + If you wish to use the Intel 82576 or 82599-based controllers in SR-IOV mode + with KVM and a Microsoft Windows Server 2008 guest try the following + workaround. The workaround is to tell KVM to emulate a different model of CPU + when using qemu to create the KVM guest: + + "-cpu qemu64,model=13" + + +Support +======= + +For general information, go to the Intel support website at: + + http://support.intel.com + +or the Intel Wired Networking project hosted by Sourceforge at: + + http://e1000.sourceforge.net + +If an issue is identified with the released source code on the supported +kernel with a supported adapter, email the specific information related +to the issue to e1000-devel@lists.sf.net |