1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
|
/*
ChibiOS/RT - Copyright (C) 2012
Joel Bodenmann aka Tectu <joel@unormal.org>
This file is part of ChibiOS/GFX.
ChibiOS/GFX is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or
(at your option) any later version.
ChibiOS/GFX is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#if !defined(GDISP_USE_SPI)
#error "GDISP_USE_SPI must be defined for the board"
#endif
/**
* @file drivers/gdisp/Nokia6610/gdisp_lld_board_olimexsam7ex256.h
* @brief GDISP Graphic Driver subsystem board interface for the Olimex SAM7-EX256 board.
*
* @addtogroup GDISP
* @{
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// mask definitions
#define BIT0 0x00000001
#define BIT1 0x00000002
#define BIT2 0x00000004
#define BIT3 0x00000008
#define BIT4 0x00000010
#define BIT5 0x00000020
#define BIT6 0x00000040
#define BIT7 0x00000080
#define BIT8 0x00000100
#define BIT9 0x00000200
#define BIT10 0x00000400
#define BIT11 0x00000800
#define BIT12 0x00001000
#define BIT13 0x00002000
#define BIT14 0x00004000
#define BIT15 0x00008000
#define BIT16 0x00010000
#define BIT17 0x00020000
#define BIT18 0x00040000
#define BIT19 0x00080000
#define BIT20 0x00100000
#define BIT21 0x00200000
#define BIT22 0x00400000
#define BIT23 0x00800000
#define BIT24 0x01000000
#define BIT25 0x02000000
#define BIT26 0x04000000
#define BIT27 0x08000000
#define BIT28 0x10000000
#define BIT29 0x20000000
#define BIT30 0x40000000
#define BIT31 0x80000000
// ******************************************************
// Pointers to AT91SAM7X256 peripheral data structures
// ******************************************************
volatile AT91PS_PIO pPIOA = AT91C_BASE_PIOA;
volatile AT91PS_PIO pPIOB = AT91C_BASE_PIOB;
volatile AT91PS_SPI pSPI = AT91C_BASE_SPI0;
volatile AT91PS_PMC pPMC = AT91C_BASE_PMC;
volatile AT91PS_PDC pPDC = AT91C_BASE_PDC_SPI0;
/**
* @brief Initialise the board for the display.
* @notes Performs the following functions:
* 1. initialise the spi port used by your display
* 2. initialise the reset pin (initial state not-in-reset)
* 3. initialise the chip select pin (initial state not-active)
* 4. initialise the backlight pin (initial state back-light off)
*
* @notapi
*/
static __inline void GDISP_LLD(init_board)(void) {
// *********************************************************************************************
// InitSpi( )
//
// Sets up SPI channel 0 for communications to Nokia 6610 LCD Display
//
// I/O ports used: PA2 = LCD Reset (set to low to reset)
// PA12 = LCD chip select (set to low to select the LCD chip)
// PA16 = SPI0_MISO Master In - Slave Out (not used in LCD interface)
// PA17 = SPI0_MOSI Master Out - Slave In pin (Serial Data to LCD slave)
// PA18 = SPI0_SPCK Serial Clock (to LCD slave)
// PB20 = backlight control (normally PWM control, 1 = full on)
//
// *********************************************************************************************}
/* This code should really use the ChibiOS driver for these functions */
// Pin for backlight
pPIOB->PIO_CODR = PIOB_LCD_BL_MASK; // Set PB20 to LOW
pPIOB->PIO_OER = PIOB_LCD_BL_MASK; // Configure PB20 as output
// Reset pin
pPIOA->PIO_SODR = PIOA_LCD_RESET_MASK; // Set PA2 to HIGH
pPIOA->PIO_OER = PIOA_LCD_RESET_MASK; // Configure PA2 as output
// CS pin - this seems to be ignored
// pPIOA->PIO_SODR = BIT12; // Set PA2 to HIGH
// pPIOA->PIO_OER = BIT12; // Configure PA2 as output
// Init SPI0
// Disable the following pins from PIO control (will be used instead by the SPI0 peripheral)
// BIT12 = PA12 -> SPI0_NPCS0 chip select
// BIT16 = PA16 -> SPI0_MISO Master In - Slave Out (not used in LCD interface)
// BIT17 = PA17 -> SPI0_MOSI Master Out - Slave In pin (Serial Data to LCD slave)
// BIT18 = PA18 -> SPI0_SPCK Serial Clock (to LCD slave)
pPIOA->PIO_PDR = BIT12 | BIT16 | BIT17 | BIT18;
pPIOA->PIO_ASR = BIT12 | BIT16 | BIT17 | BIT18;
pPIOA->PIO_BSR = 0;
//enable the clock of SPI
pPMC->PMC_PCER = 1 << AT91C_ID_SPI0;
// Fixed mode
pSPI->SPI_CR = 0x81; //SPI Enable, Sowtware reset
pSPI->SPI_CR = 0x01; //SPI Enable
//pSPI->SPI_MR = 0xE0019; //Master mode, fixed select, disable decoder, FDIV=1 (MCK), PCS=1110
pSPI->SPI_MR = 0xE0011; //Master mode, fixed select, disable decoder, FDIV=0 (MCK), PCS=1110
//pSPI->SPI_CSR[0] = 0x01010C11; //9bit, CPOL=1, ClockPhase=0, SCLK = 48Mhz/32*12 = 125kHz
pSPI->SPI_CSR[0] = 0x01010311; //9bit, CPOL=1, ClockPhase=0, SCLK = 48Mhz/8 = 6MHz if using commented MR line above
}
/**
* @brief Set or clear the lcd reset pin.
*
* @param[in] state TRUE = lcd in reset, FALSE = normal operation
*
* @notapi
*/
static __inline void GDISP_LLD(setpin_reset)(bool_t state) {
if (state)
palClearPad(IOPORT1, PIOA_LCD_RESET);
// pPIOA->PIO_CODR = PIOA_LCD_RESET_MASK;
else
palSetPad(IOPORT1, PIOA_LCD_RESET);
// pPIOA->PIO_SODR = PIOA_LCD_RESET_MASK;
}
/**
* @brief Set the lcd back-light level.
* @note For now 0% turns the backlight off, anything else the backlight is on.
* While the hardware supports PWM backlight control, we are not using it
* yet.
*
* @param[in] percent 0 to 100%
*
* @notapi
*/
static __inline void GDISP_LLD(set_backlight)(uint8_t percent) {
if (percent)
palSetPad(IOPORT2, PIOB_LCD_BL);
// pPIOB->PIO_SODR = PIOB_LCD_BL_MASK;
else
palClearPad(IOPORT2, PIOB_LCD_BL);
// pPIOB->PIO_CODR = PIOB_LCD_BL_MASK;
}
/**
* @brief Take exclusive control of the bus
*
* @notapi
*/
static __inline void GDISP_LLD(get_bus)(void) {
// Nothing to do for this board as the LCD is the only device on the SPI port
}
/**
* @brief Release exclusive control of the bus
*
* @notapi
*/
static __inline void GDISP_LLD(release_bus)(void) {
// Nothing to do for this board as the LCD is the only device on the SPI port
}
/**
* @brief Send an 8 bit command to the lcd.
*
* @param[in] cmd The command to send
*
* @notapi
*/
static __inline void GDISP_LLD(write_cmd)(uint16_t cmd) {
// wait for the previous transfer to complete
while((pSPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0);
// send the command
pSPI->SPI_TDR = data & 0xFF;
}
/**
* @brief Send an 8 bit data to the lcd.
*
* @param[in] data The data to send
*
* @notapi
*/
static __inline void GDISP_LLD(write_data)(uint16_t data) {
// wait for the previous transfer to complete
while((pSPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0);
// send the data
pSPI->SPI_TDR = data | 0x0100;
}
#if GDISP_HARDWARE_READPIXEL || GDISP_HARDWARE_SCROLL || defined(__DOXYGEN__)
/**
* @brief Read data from the lcd.
*
* @return The data from the lcd
*
* @notapi
*/
static __inline uint16_t GDISP_LLD(read_data)(void) {
#error "gdispNokia6610: GDISP_HARDWARE_READPIXEL and GDISP_HARDWARE_SCROLL are not supported on this board"
return 0;
}
#endif
#endif /* _GDISP_LLD_BOARD_H */
/** @} */
|