From ab8668b14ee05854dfe935bf143be7ebe051b8f5 Mon Sep 17 00:00:00 2001 From: Dean Camera Date: Tue, 4 May 2010 11:33:51 +0000 Subject: Removed software PDI/TPI emulation from the AVRISP-MKII clone project, as it was very buggy. PDI and TPI must now be implemented via seperate headers instead of the one unified ISP/TPI/PDI header. --- Projects/AVRISP-MKII/AVRISP.txt | 30 +--- Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c | 243 +-------------------------- Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.h | 28 --- 3 files changed, 8 insertions(+), 293 deletions(-) (limited to 'Projects') diff --git a/Projects/AVRISP-MKII/AVRISP.txt b/Projects/AVRISP-MKII/AVRISP.txt index 610903110..034df6717 100644 --- a/Projects/AVRISP-MKII/AVRISP.txt +++ b/Projects/AVRISP-MKII/AVRISP.txt @@ -56,17 +56,12 @@ * Note that this design currently has the following limitations: * - Minimum ISP target clock speed of 500KHz due to hardware SPI module prescaler limitations * - No reversed/shorted target connector detection and notification - * - Very slow TPI and PDI programming when in software emulated USART mode + * - A seperate header is required for each of the ISP, PDI and TPI programming protocols that the user wishes to use * * On AVR models with an ADC converter, AVCC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be * set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models * without an ADC converter, VTARGET will report a fixed 5V level at all times. * - * When compiled for the XPLAIN board target, this will automatically configure itself for the correct connections to the - * XPLAIN's XMEGA AVR, and will enable hardware PDI/TPI only programming support (since ISP mode is not needed). Note that - * the first revision XPLAIN board lacks a bootloader on the AT90USB1287, and thus for this firmware to be loaded, an external - * programmer will be required. - * * While this application can be compiled for USB AVRs with as little as 8KB of FLASH, for full functionality 16KB or more * of FLASH is required. On 8KB devices, ISP or PDI/TPI programming support can be disabled to reduce program size. * @@ -128,7 +123,7 @@ * PDI 6 Pin Layout: * * - * MISO 2 + * Tx/Rx 2 * DATA * 1 * @@ -148,7 +143,7 @@ * 4 * * - * PORTx.y 2, 3 + * XCLK * CLOCK * 5 * @@ -160,9 +155,7 @@ * * * 1 Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only \n - * 2 When XPROG_VIA_HARDWARE_USART is set, the AVR's Tx and Rx become the DATA line when connected together - * via a pair of 220 ohm resistors, and the AVR's XCK pin becomes CLOCK. \n - * 3 See AUX line related tokens in the \ref SSec_Options section + * 2 The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors \n * * \section Sec_TPI TPI Connections * Connections to the device for TPI programming1 (when enabled): @@ -174,7 +167,7 @@ * TPI 6 Pin Layout: * * - * MISO 2 + * Tx/Rx 2 * DATA * 1 * @@ -184,7 +177,7 @@ * 2 * * - * SCLK 2 + * XCLK 2 * CLOCK * 3 * @@ -206,8 +199,7 @@ * * * 1 Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only \n - * 2 When XPROG_VIA_HARDWARE_USART is set, the AVR's Tx and Rx become the DATA line when connected together - * via a pair of 220 ohm resistors, and the AVR's XCK pin becomes CLOCK. \n + * 2 The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors \n * 3 See AUX line related tokens in the \ref SSec_Options section * * \section SSec_Options Project Options @@ -261,14 +253,6 @@ * Define to enable PDI and TPI programming protocol support. Ignored when compiled for the XPLAIN board. * * - * XPROG_VIA_HARDWARE_USART - * Makefile CDEFS - * Define to force the PDI and TPI protocols (when enabled) to use the much faster hardware USART instead of bit-banging - * to match the official AVRISP pinout. This breaks pinout compatibility with the official AVRISP MKII (and requires - * seperate ISP, PDI, and TPI programming headers) but increases programming speed dramatically. - * Ignored when compiled for the XPLAIN board. - * - * * NO_VTARGET_DETECT * Makefile CDEFS * Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer diff --git a/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c b/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c index e2c6fd6a2..72a38f824 100644 --- a/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c +++ b/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c @@ -39,115 +39,13 @@ #if defined(ENABLE_XPROG_PROTOCOL) || defined(__DOXYGEN__) /** Flag to indicate if the USART is currently in Tx or Rx mode. */ -volatile bool IsSending; - -#if !defined(XPROG_VIA_HARDWARE_USART) -/** Software USART raw frame bits for transmission/reception. */ -volatile uint16_t SoftUSART_Data; - -/** Bits remaining to be sent or received via the software USART - set as a GPIOR for speed. */ -#define SoftUSART_BitCount GPIOR2 - - -/** ISR to manage the PDI software USART when bit-banged PDI USART mode is selected. */ -ISR(TIMER1_COMPA_vect, ISR_BLOCK) -{ - /* Toggle CLOCK pin in a single cycle (see AVR datasheet) */ - BITBANG_PDICLOCK_PIN = BITBANG_PDICLOCK_MASK; - - /* If not sending or receiving, just exit */ - if (!(SoftUSART_BitCount)) - return; - - /* Check to see if we are at a rising or falling edge of the clock */ - if (BITBANG_PDICLOCK_PORT & BITBANG_PDICLOCK_MASK) - { - /* If at rising clock edge and we are in send mode, abort */ - if (IsSending) - return; - - /* Wait for the start bit when receiving */ - if ((SoftUSART_BitCount == BITS_IN_USART_FRAME) && (BITBANG_PDIDATA_PIN & BITBANG_PDIDATA_MASK)) - return; - - /* Shift in the bit one less than the frame size in position, so that the start bit will eventually - * be discarded leaving the data to be byte-aligned for quick access (subtract 9 as we are ORing to the MSB) */ - if (BITBANG_PDIDATA_PIN & BITBANG_PDIDATA_MASK) - ((uint8_t*)&SoftUSART_Data)[1] |= (1 << (BITS_IN_USART_FRAME - 9)); - - SoftUSART_Data >>= 1; - SoftUSART_BitCount--; - } - else - { - /* If at falling clock edge and we are in receive mode, abort */ - if (!IsSending) - return; - - /* Set the data line to the next bit value */ - if (((uint8_t*)&SoftUSART_Data)[0] & 0x01) - BITBANG_PDIDATA_PORT |= BITBANG_PDIDATA_MASK; - else - BITBANG_PDIDATA_PORT &= ~BITBANG_PDIDATA_MASK; - - SoftUSART_Data >>= 1; - SoftUSART_BitCount--; - } -} - -/** ISR to manage the TPI software USART when bit-banged TPI USART mode is selected. */ -ISR(TIMER1_CAPT_vect, ISR_BLOCK) -{ - /* Toggle CLOCK pin in a single cycle (see AVR datasheet) */ - BITBANG_TPICLOCK_PIN = BITBANG_TPICLOCK_MASK; - - /* If not sending or receiving, just exit */ - if (!(SoftUSART_BitCount)) - return; - - /* Check to see if we are at a rising or falling edge of the clock */ - if (BITBANG_TPICLOCK_PORT & BITBANG_TPICLOCK_MASK) - { - /* If at rising clock edge and we are in send mode, abort */ - if (IsSending) - return; - - /* Wait for the start bit when receiving */ - if ((SoftUSART_BitCount == BITS_IN_USART_FRAME) && (BITBANG_TPIDATA_PIN & BITBANG_TPIDATA_MASK)) - return; - - /* Shift in the bit one less than the frame size in position, so that the start bit will eventually - * be discarded leaving the data to be byte-aligned for quick access (subtract 9 as we are ORing to the MSB) */ - if (BITBANG_TPIDATA_PIN & BITBANG_TPIDATA_MASK) - ((uint8_t*)&SoftUSART_Data)[1] |= (1 << (BITS_IN_USART_FRAME - 9)); - - SoftUSART_Data >>= 1; - SoftUSART_BitCount--; - } - else - { - /* If at falling clock edge and we are in receive mode, abort */ - if (!IsSending) - return; - - /* Set the data line to the next bit value */ - if (((uint8_t*)&SoftUSART_Data)[0] & 0x01) - BITBANG_TPIDATA_PORT |= BITBANG_TPIDATA_MASK; - else - BITBANG_TPIDATA_PORT &= ~BITBANG_TPIDATA_MASK; - - SoftUSART_Data >>= 1; - SoftUSART_BitCount--; - } -} -#endif +volatile bool IsSending; /** Enables the target's PDI interface, holding the target in reset until PDI mode is exited. */ void XPROGTarget_EnableTargetPDI(void) { IsSending = false; -#if defined(XPROG_VIA_HARDWARE_USART) /* Set Tx and XCK as outputs, Rx as input */ DDRD |= (1 << 5) | (1 << 3); DDRD &= ~(1 << 2); @@ -160,24 +58,6 @@ void XPROGTarget_EnableTargetPDI(void) UBRR1 = (F_CPU / XPROG_HARDWARE_SPEED); UCSR1B = (1 << TXEN1); UCSR1C = (1 << UMSEL10) | (1 << UPM11) | (1 << USBS1) | (1 << UCSZ11) | (1 << UCSZ10) | (1 << UCPOL1); -#else - /* Set DATA and CLOCK lines to outputs */ - BITBANG_PDIDATA_DDR |= BITBANG_PDIDATA_MASK; - BITBANG_PDICLOCK_DDR |= BITBANG_PDICLOCK_MASK; - - /* Set DATA line low for at least 1ms to ensure that the device is ready for PDI mode to be entered */ - BITBANG_PDIDATA_PORT &= ~BITBANG_PDIDATA_MASK; - _delay_ms(1); - - /* Set DATA line high for at least 90ns to disable /RESET functionality */ - BITBANG_PDIDATA_PORT |= BITBANG_PDIDATA_MASK; - _delay_us(1); - - /* Fire timer compare channel A ISR to manage the software USART */ - OCR1A = BITS_BETWEEN_USART_CLOCKS; - TCCR1B = (1 << WGM12) | (1 << CS10); - TIMSK1 = (1 << OCIE1A); -#endif /* Send two BREAKs of 12 bits each to enable PDI interface (need at least 16 idle bits) */ XPROGTarget_SendBreak(); @@ -194,7 +74,6 @@ void XPROGTarget_EnableTargetTPI(void) AUX_LINE_PORT &= ~AUX_LINE_MASK; _delay_us(1); -#if defined(XPROG_VIA_HARDWARE_USART) /* Set Tx and XCK as outputs, Rx as input */ DDRD |= (1 << 5) | (1 << 3); DDRD &= ~(1 << 2); @@ -203,19 +82,6 @@ void XPROGTarget_EnableTargetTPI(void) UBRR1 = (F_CPU / XPROG_HARDWARE_SPEED); UCSR1B = (1 << TXEN1); UCSR1C = (1 << UMSEL10) | (1 << UPM11) | (1 << USBS1) | (1 << UCSZ11) | (1 << UCSZ10) | (1 << UCPOL1); -#else - /* Set DATA and CLOCK lines to outputs */ - BITBANG_TPIDATA_DDR |= BITBANG_TPIDATA_MASK; - BITBANG_TPICLOCK_DDR |= BITBANG_TPICLOCK_MASK; - - /* Set DATA line high for idle state */ - BITBANG_TPIDATA_PORT |= BITBANG_TPIDATA_MASK; - - /* Fire timer capture channel ISR to manage the software USART */ - ICR1 = BITS_BETWEEN_USART_CLOCKS; - TCCR1B = (1 << WGM13) | (1 << WGM12) | (1 << CS10); - TIMSK1 = (1 << ICIE1); -#endif /* Send two BREAKs of 12 bits each to enable TPI interface (need at least 16 idle bits) */ XPROGTarget_SendBreak(); @@ -228,7 +94,6 @@ void XPROGTarget_DisableTargetPDI(void) /* Switch to Rx mode to ensure that all pending transmissions are complete */ XPROGTarget_SetRxMode(); -#if defined(XPROG_VIA_HARDWARE_USART) /* Turn off receiver and transmitter of the USART, clear settings */ UCSR1A = ((1 << TXC1) | (1 << RXC1)); UCSR1B = 0; @@ -237,18 +102,6 @@ void XPROGTarget_DisableTargetPDI(void) /* Tristate all pins */ DDRD &= ~((1 << 5) | (1 << 3)); PORTD &= ~((1 << 5) | (1 << 3) | (1 << 2)); -#else - /* Turn off software USART management timer */ - TCCR1B = 0; - - /* Set DATA and CLOCK lines to inputs */ - BITBANG_PDIDATA_DDR &= ~BITBANG_PDIDATA_MASK; - BITBANG_PDICLOCK_DDR &= ~BITBANG_PDICLOCK_MASK; - - /* Tristate DATA and CLOCK lines */ - BITBANG_PDIDATA_PORT &= ~BITBANG_PDIDATA_MASK; - BITBANG_PDICLOCK_PORT &= ~BITBANG_PDICLOCK_MASK; -#endif } /** Disables the target's TPI interface, exits programming mode and starts the target's application. */ @@ -257,7 +110,6 @@ void XPROGTarget_DisableTargetTPI(void) /* Switch to Rx mode to ensure that all pending transmissions are complete */ XPROGTarget_SetRxMode(); -#if defined(XPROG_VIA_HARDWARE_USART) /* Turn off receiver and transmitter of the USART, clear settings */ UCSR1A |= (1 << TXC1) | (1 << RXC1); UCSR1B = 0; @@ -266,18 +118,6 @@ void XPROGTarget_DisableTargetTPI(void) /* Set all USART lines as input, tristate */ DDRD &= ~((1 << 5) | (1 << 3)); PORTD &= ~((1 << 5) | (1 << 3) | (1 << 2)); -#else - /* Turn off software USART management timer */ - TCCR1B = 0; - - /* Set DATA and CLOCK lines to inputs */ - BITBANG_TPIDATA_DDR &= ~BITBANG_TPIDATA_MASK; - BITBANG_TPICLOCK_DDR &= ~BITBANG_TPICLOCK_MASK; - - /* Tristate DATA and CLOCK lines */ - BITBANG_TPIDATA_PORT &= ~BITBANG_TPIDATA_MASK; - BITBANG_TPICLOCK_PORT &= ~BITBANG_TPICLOCK_MASK; -#endif /* Tristate target /RESET line */ AUX_LINE_DDR &= ~AUX_LINE_MASK; @@ -294,30 +134,10 @@ void XPROGTarget_SendByte(const uint8_t Byte) if (!(IsSending)) XPROGTarget_SetTxMode(); -#if defined(XPROG_VIA_HARDWARE_USART) /* Wait until there is space in the hardware Tx buffer before writing */ while (!(UCSR1A & (1 << UDRE1))); UCSR1A |= (1 << TXC1); UDR1 = Byte; -#else - /* Calculate the new USART frame data here while while we wait for a previous byte (if any) to finish sending */ - uint16_t NewUSARTData = ((1 << 11) | (1 << 10) | (0 << 9) | ((uint16_t)Byte << 1) | (0 << 0)); - - /* Compute Even parity - while a bit is still set, chop off lowest bit and toggle parity bit */ - uint8_t ParityData = Byte; - while (ParityData) - { - NewUSARTData ^= (1 << 9); - ParityData &= (ParityData - 1); - } - - /* Wait until transmitter is idle before writing new data */ - while (SoftUSART_BitCount); - - /* Data shifted out LSB first, START DATA PARITY STOP STOP */ - SoftUSART_Data = NewUSARTData; - SoftUSART_BitCount = BITS_IN_USART_FRAME; -#endif if (TimeoutMSRemaining) TimeoutMSRemaining = COMMAND_TIMEOUT_MS; @@ -333,7 +153,6 @@ uint8_t XPROGTarget_ReceiveByte(void) if (IsSending) XPROGTarget_SetRxMode(); -#if defined(XPROG_VIA_HARDWARE_USART) /* Wait until a byte has been received before reading */ while (!(UCSR1A & (1 << RXC1)) && TimeoutMSRemaining); @@ -341,17 +160,6 @@ uint8_t XPROGTarget_ReceiveByte(void) TimeoutMSRemaining = COMMAND_TIMEOUT_MS; return UDR1; -#else - /* Wait until a byte has been received before reading */ - SoftUSART_BitCount = BITS_IN_USART_FRAME; - while (SoftUSART_BitCount && TimeoutMSRemaining); - - if (TimeoutMSRemaining) - TimeoutMSRemaining = COMMAND_TIMEOUT_MS; - - /* Throw away the parity and stop bits to leave only the data (start bit is already discarded) */ - return (uint8_t)SoftUSART_Data; -#endif } /** Sends a BREAK via the USART to the attached target, consisting of a full frame of idle bits. */ @@ -361,7 +169,6 @@ void XPROGTarget_SendBreak(void) if (!(IsSending)) XPROGTarget_SetTxMode(); -#if defined(XPROG_VIA_HARDWARE_USART) /* Need to do nothing for a full frame to send a BREAK */ for (uint8_t i = 0; i < BITS_IN_USART_FRAME; i++) { @@ -369,13 +176,6 @@ void XPROGTarget_SendBreak(void) while (PIND & (1 << 5)); while (!(PIND & (1 << 5))); } -#else - while (SoftUSART_BitCount); - - /* Need to do nothing for a full frame to send a BREAK */ - SoftUSART_Data = 0x0FFF; - SoftUSART_BitCount = BITS_IN_USART_FRAME; -#endif if (TimeoutMSRemaining) TimeoutMSRemaining = COMMAND_TIMEOUT_MS; @@ -383,7 +183,6 @@ void XPROGTarget_SendBreak(void) static void XPROGTarget_SetTxMode(void) { -#if defined(XPROG_VIA_HARDWARE_USART) /* Wait for a full cycle of the clock */ while (PIND & (1 << 5)); while (!(PIND & (1 << 5))); @@ -395,25 +194,6 @@ static void XPROGTarget_SetTxMode(void) UCSR1B |= (1 << TXEN1); IsSending = true; -#else - while (SoftUSART_BitCount && TimeoutMSRemaining); - - /* Wait for a full cycle of the clock */ - SoftUSART_Data = 0x0001; - SoftUSART_BitCount = 1; - while (SoftUSART_BitCount); - - if (XPROG_SelectedProtocol == XPRG_PROTOCOL_PDI) - { - BITBANG_PDIDATA_PORT |= BITBANG_PDIDATA_MASK; - BITBANG_PDIDATA_DDR |= BITBANG_PDIDATA_MASK; - } - else - { - BITBANG_TPIDATA_PORT |= BITBANG_TPIDATA_MASK; - BITBANG_TPIDATA_DDR |= BITBANG_TPIDATA_MASK; - } -#endif if (TimeoutMSRemaining) TimeoutMSRemaining = COMMAND_TIMEOUT_MS; @@ -423,7 +203,6 @@ static void XPROGTarget_SetTxMode(void) static void XPROGTarget_SetRxMode(void) { -#if defined(XPROG_VIA_HARDWARE_USART) while (!(UCSR1A & (1 << TXC1))); UCSR1A |= (1 << TXC1); @@ -432,26 +211,6 @@ static void XPROGTarget_SetRxMode(void) DDRD &= ~(1 << 3); PORTD &= ~(1 << 3); -#else - while (SoftUSART_BitCount && TimeoutMSRemaining); - - if (XPROG_SelectedProtocol == XPRG_PROTOCOL_PDI) - { - BITBANG_PDIDATA_DDR &= ~BITBANG_PDIDATA_MASK; - BITBANG_PDIDATA_PORT &= ~BITBANG_PDIDATA_MASK; - - /* Wait until DATA line has been pulled up to idle by the target */ - while (!(BITBANG_PDIDATA_PIN & BITBANG_PDIDATA_MASK) && TimeoutMSRemaining); - } - else - { - BITBANG_TPIDATA_DDR &= ~BITBANG_TPIDATA_MASK; - BITBANG_TPIDATA_PORT &= ~BITBANG_TPIDATA_MASK; - - /* Wait until DATA line has been pulled up to idle by the target */ - while (!(BITBANG_TPIDATA_PIN & BITBANG_TPIDATA_MASK) && TimeoutMSRemaining); - } -#endif if (TimeoutMSRemaining) TimeoutMSRemaining = COMMAND_TIMEOUT_MS; diff --git a/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.h b/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.h index e0400e2cc..65ec11bcf 100644 --- a/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.h +++ b/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.h @@ -54,38 +54,10 @@ #define ENABLE_XPROG_PROTOCOL #endif #endif - - /* Defines: */ - #if ((BOARD == BOARD_XPLAIN) || (BOARD == BOARD_XPLAIN_REV1)) - #define XPROG_VIA_HARDWARE_USART - #else - #define BITBANG_PDIDATA_PORT PORTB - #define BITBANG_PDIDATA_DDR DDRB - #define BITBANG_PDIDATA_PIN PINB - #define BITBANG_PDIDATA_MASK (1 << 3) - - #define BITBANG_PDICLOCK_PORT AUX_LINE_PORT - #define BITBANG_PDICLOCK_DDR AUX_LINE_DDR - #define BITBANG_PDICLOCK_PIN AUX_LINE_PIN - #define BITBANG_PDICLOCK_MASK AUX_LINE_MASK - - #define BITBANG_TPIDATA_PORT PORTB - #define BITBANG_TPIDATA_DDR DDRB - #define BITBANG_TPIDATA_PIN PINB - #define BITBANG_TPIDATA_MASK (1 << 3) - - #define BITBANG_TPICLOCK_PORT PORTB - #define BITBANG_TPICLOCK_DDR DDRB - #define BITBANG_TPICLOCK_PIN PINB - #define BITBANG_TPICLOCK_MASK (1 << 1) - #endif /** Serial carrier TPI/PDI speed when hardware TPI/PDI mode is used */ #define XPROG_HARDWARE_SPEED 1000000 - /** Number of cycles between each clock when software USART mode is used */ - #define BITS_BETWEEN_USART_CLOCKS 100 - /** Total number of bits in a single USART frame */ #define BITS_IN_USART_FRAME 12 -- cgit v1.2.3