diff options
Diffstat (limited to 'Projects/AVRISP/Lib/XPROG/PDITarget.c')
| -rw-r--r-- | Projects/AVRISP/Lib/XPROG/PDITarget.c | 14 |
1 files changed, 7 insertions, 7 deletions
diff --git a/Projects/AVRISP/Lib/XPROG/PDITarget.c b/Projects/AVRISP/Lib/XPROG/PDITarget.c index 2c6ffd9a6..4070c0996 100644 --- a/Projects/AVRISP/Lib/XPROG/PDITarget.c +++ b/Projects/AVRISP/Lib/XPROG/PDITarget.c @@ -36,12 +36,12 @@ #define INCLUDE_FROM_PDITARGET_C
#include "PDITarget.h"
-#if defined(ENABLE_PDI_PROTOCOL) || defined(__DOXYGEN__)
+#if defined(ENABLE_XPROG_PROTOCOL) || defined(__DOXYGEN__)
/** Flag to indicate if the USART is currently in Tx or Rx mode. */
volatile bool IsSending;
-#if !defined(PDI_VIA_HARDWARE_USART)
+#if !defined(XPROG_VIA_HARDWARE_USART)
/** Software USART raw frame bits for transmission/reception. */
volatile uint16_t SoftUSART_Data;
@@ -99,7 +99,7 @@ ISR(TIMER1_COMPA_vect, ISR_BLOCK) /** Enables the target's PDI interface, holding the target in reset until PDI mode is exited. */
void PDITarget_EnableTargetPDI(void)
{
-#if defined(PDI_VIA_HARDWARE_USART)
+#if defined(XPROG_VIA_HARDWARE_USART)
/* Set Tx and XCK as outputs, Rx as input */
DDRD |= (1 << 5) | (1 << 3);
DDRD &= ~(1 << 2);
@@ -142,7 +142,7 @@ void PDITarget_EnableTargetPDI(void) /** Disables the target's PDI interface, exits programming mode and starts the target's application. */
void PDITarget_DisableTargetPDI(void)
{
-#if defined(PDI_VIA_HARDWARE_USART)
+#if defined(XPROG_VIA_HARDWARE_USART)
/* Turn off receiver and transmitter of the USART, clear settings */
UCSR1A |= (1 << TXC1) | (1 << RXC1);
UCSR1B = 0;
@@ -168,7 +168,7 @@ void PDITarget_DisableTargetPDI(void) */
void PDITarget_SendByte(const uint8_t Byte)
{
-#if defined(PDI_VIA_HARDWARE_USART)
+#if defined(XPROG_VIA_HARDWARE_USART)
/* Switch to Tx mode if currently in Rx mode */
if (!(IsSending))
{
@@ -221,7 +221,7 @@ void PDITarget_SendByte(const uint8_t Byte) */
uint8_t PDITarget_ReceiveByte(void)
{
-#if defined(PDI_VIA_HARDWARE_USART)
+#if defined(XPROG_VIA_HARDWARE_USART)
/* Switch to Rx mode if currently in Tx mode */
if (IsSending)
{
@@ -264,7 +264,7 @@ uint8_t PDITarget_ReceiveByte(void) /** Sends a BREAK via the USART to the attached target, consisting of a full frame of idle bits. */
void PDITarget_SendBreak(void)
{
-#if defined(PDI_VIA_HARDWARE_USART)
+#if defined(XPROG_VIA_HARDWARE_USART)
/* Switch to Tx mode if currently in Rx mode */
if (!(IsSending))
{
|