diff options
Diffstat (limited to 'Projects/AVRISP-MKII/AVRISP-MKII.txt')
| -rw-r--r-- | Projects/AVRISP-MKII/AVRISP-MKII.txt | 32 |
1 files changed, 16 insertions, 16 deletions
diff --git a/Projects/AVRISP-MKII/AVRISP-MKII.txt b/Projects/AVRISP-MKII/AVRISP-MKII.txt index 3d43cb137..cd1faf094 100644 --- a/Projects/AVRISP-MKII/AVRISP-MKII.txt +++ b/Projects/AVRISP-MKII/AVRISP-MKII.txt @@ -214,60 +214,60 @@ * </tr> * <tr> * <td>AUX_LINE_PORT</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>PORT register for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>AUX_LINE_PIN</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>PIN register for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>AUX_LINE_DDR</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>DDR register for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>AUX_LINE_MASK</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Mask for the programmer's AUX target line. The use of this line varies between the programming protocols, * but is generally used for the target's /RESET line. <b>Must not be the AVR's /SS pin</b>. * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>VTARGET_ADC_CHANNEL</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined. * \n \n <i>Ignored when compiled for targets lacking an ADC.</i></td> * </tr> * <tr> * <td>ENABLE_ISP_PROTOCOL</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to enable SPI programming protocol support. * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>ENABLE_XPROG_PROTOCOL</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to enable PDI and TPI programming protocol support. * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> * </tr> * <tr> * <td>NO_VTARGET_DETECT</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer * to report a fixed 3.3V target voltage to the host regardless of the real target voltage. * \n \n <i>Ignored when compiled for targets lacking an ADC.</i></td> * </tr> * <tr> * <td>VTARGET_REF_VOLTS</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply * voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage * to the ADC. @@ -275,14 +275,14 @@ * </tr> * <tr> * <td>VTARGET_USE_INTERNAL_REF</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Selects the internal 2.56V ADC reference voltage, instead of using the AVR's VREF pin. When enabled, this option will * override the VTARGET_REF_VOLTS configuration option. * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> * </tr> * <tr> * <td>VTARGET_SCALE_FACTOR</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the * ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be * measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set @@ -291,7 +291,7 @@ * </tr> * <tr> * <td>LIBUSB_DRIVER_COMPAT</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making * the code compatible with software such as avrdude (all platforms) that use the libUSB driver. * @@ -299,7 +299,7 @@ * </tr> * <tr> * <td>RESET_TOGGLES_LIBUSB_COMPAT</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to make the /RESET line of the AVR toggle between Jungo and libUSB driver compatibility modes. Each time the AVR is * reset externally via the reset pin, the compatibility mode will be toggled. The compatibility mode is preserved between * power cycles and is not toggled via other forms of reset such as Watchdog or Brown Out. @@ -308,19 +308,19 @@ * </tr> * <tr> * <td>XCK_RESCUE_CLOCK_ENABLE</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to move the ISP rescue clock to the AVR's XCK pin instead of the OCR1A output pin. This is useful for existing programming * hardware that does not expose the OCR1A pin of the AVR, but <i>may</i> cause some issues with PDI programming mode.</td> * </tr> * <tr> * <td>INVERTED_ISP_MISO</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to invert the received data on the ISP MISO line. This is sometimes needed depending on the level translation hardware used, * if the translator hardware inverts the received logic level.</td> * </tr> * <tr> * <td>FIRMWARE_VERSION_MINOR</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>Define to set the minor firmware revision nunber reported to the host on request. By default this will use a firmware version compatible * with the latest Atmel IDE version, however if desired the reported minor value can be adjusted here.</td> * </tr> |