From a7a647b7f6d707e9c952461beeca1f3637039d36 Mon Sep 17 00:00:00 2001 From: Rodrigo Feijao Date: Sun, 17 Feb 2019 02:34:07 +0000 Subject: Add support to XD60 Rev3 (#4938) * Add preliminary support to XD60 Rev3 PCB (Supports the 12 underglow LEDs, but split spacebar still not wired/implemented). * * xd60_rev3 folder removed * xd60 rev2 and rev3 added * ifndef replaced with pragma once at rev3 config.h * Readme updated * new updated statement at keyboards/xd60/readme.md Co-Authored-By: rodrigofeijao * Update keyboards/xd60/readme.md Co-Authored-By: rodrigofeijao * Update keyboards/xd60/readme.md Co-Authored-By: rodrigofeijao * Update keyboards/xd60/readme.md Co-Authored-By: rodrigofeijao * Update keyboards/xd60/readme.md Co-Authored-By: rodrigofeijao * * XXXXX removed and replaced with 7X * removed unecessary declarations * Update keyboards/xd60/keymaps/styr/keymap.c Co-Authored-By: rodrigofeijao * action_layer.h include removed * * action_get_macro removed * IS_COMMAND() removed * BOOTLOADER defined --- keyboards/xd60/config.h | 74 ----------------------------------- keyboards/xd60/keymaps/styr/keymap.c | 56 ++++++++++++++++++++++++++ keyboards/xd60/keymaps/styr/readme.md | 7 ++++ keyboards/xd60/readme.md | 13 ++++-- keyboards/xd60/rev2/config.h | 74 +++++++++++++++++++++++++++++++++++ keyboards/xd60/rev2/rules.mk | 67 +++++++++++++++++++++++++++++++ keyboards/xd60/rev3/config.h | 71 +++++++++++++++++++++++++++++++++ keyboards/xd60/rev3/rules.mk | 67 +++++++++++++++++++++++++++++++ keyboards/xd60/rules.mk | 67 ------------------------------- 9 files changed, 351 insertions(+), 145 deletions(-) delete mode 100644 keyboards/xd60/config.h create mode 100644 keyboards/xd60/keymaps/styr/keymap.c create mode 100644 keyboards/xd60/keymaps/styr/readme.md create mode 100644 keyboards/xd60/rev2/config.h create mode 100644 keyboards/xd60/rev2/rules.mk create mode 100644 keyboards/xd60/rev3/config.h create mode 100644 keyboards/xd60/rev3/rules.mk delete mode 100644 keyboards/xd60/rules.mk (limited to 'keyboards') diff --git a/keyboards/xd60/config.h b/keyboards/xd60/config.h deleted file mode 100644 index 6c447b89f..000000000 --- a/keyboards/xd60/config.h +++ /dev/null @@ -1,74 +0,0 @@ -/* -Copyright 2012 Jun Wako - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see . -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0001 -#define MANUFACTURER XIUDI -#define PRODUCT XD60v2 -#define DESCRIPTION XD60 v2 Keyboard PCB by XIUDI - -/* key matrix size */ -#define MATRIX_ROWS 5 -#define MATRIX_COLS 14 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * -*/ -#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } -#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } -#define UNUSED_PINS - -/* Backlight Setup */ -#define BACKLIGHT_PIN F5 -#define BACKLIGHT_LEVELS 6 - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 - -/* RGB Underglow - * F6 PIN for XD60v2 that has pre-soldered WS2812 LEDs - */ -#define RGB_DI_PIN F6 -#define RGBLIGHT_ANIMATIONS -#define RGBLED_NUM 6 // Number of LEDs -#define RGBLIGHT_HUE_STEP 10 -#define RGBLIGHT_SAT_STEP 17 -#define RGBLIGHT_VAL_STEP 17 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -#endif diff --git a/keyboards/xd60/keymaps/styr/keymap.c b/keyboards/xd60/keymaps/styr/keymap.c new file mode 100644 index 000000000..2fbfe2563 --- /dev/null +++ b/keyboards/xd60/keymaps/styr/keymap.c @@ -0,0 +1,56 @@ +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FL 1 +#define _LL 2 + +enum custom_keycodes { + MACRO_STRING +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + // 0: Base Layer + [_BL] = LAYOUT_all( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + MO(_LL), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_DEL, \ + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, MO(_FL), KC_RALT, KC_LEFT, KC_DOWN, KC_RIGHT), + + // 1: Function Layer + [_FL] = LAYOUT_all( + XXXXXXX, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_F13, KC_F14, \ + XXXXXXX, RGB_TOG, RGB_MOD, RGB_RMOD, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, RGB_HUI, RGB_HUD, XXXXXXX, RGB_VAI, RGB_VAD, XXXXXXX, \ + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, \ + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_MS_BTN1, KC_MS_UP, KC_MS_BTN2, \ + XXXXXXX, XXXXXXX, XXXXXXX, MACRO_STRING, XXXXXXX, F(0), KC_MS_LEFT, KC_MS_DOWN, KC_MS_RIGHT), + + [_LL] = LAYOUT_all( + XXXXXXX, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_F13, KC_F14, \ + XXXXXXX, RGB_TOG, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, \ + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC__MUTE, \ + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_VOLU, KC_MPLY, \ + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, F(0), KC_MRWD, KC_VOLD, KC_MFFD), + + +}; + +// Macros +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case MACRO_STRING: + if(record->event.pressed){ + SEND_STRING("My Custom String"); + } + return false; + break; + default: + return true; + } +} + +// Loop +void matrix_scan_user(void) { + // Empty +}; diff --git a/keyboards/xd60/keymaps/styr/readme.md b/keyboards/xd60/keymaps/styr/readme.md new file mode 100644 index 000000000..8d9edf7c4 --- /dev/null +++ b/keyboards/xd60/keymaps/styr/readme.md @@ -0,0 +1,7 @@ +# Keyboard Layout by Styr + +## Additional Notes +Default Keymap for XD60 as indicated on the original sale page. + +## Build +To build the default keymap, simply run `make xd60/rev3:styr`. diff --git a/keyboards/xd60/readme.md b/keyboards/xd60/readme.md index 24f07c47b..b9862428c 100644 --- a/keyboards/xd60/readme.md +++ b/keyboards/xd60/readme.md @@ -6,11 +6,16 @@ Compact 60% with arrows. ![Top View of a pair of XD60 Keyboard](https://i.imgur.com/3Jq2743.jpg) Keyboard Maintainer: QMK Community -Hardware Supported: XD60 PCB +Hardware Supported: XD60 PCB rev2 & rev3 Hardware Availability: https://www.massdrop.com/buy/xd60-xd64-custom-mechanical-keyboard-kit?mode=guest_open -Make example for this keyboard (after setting up your build environment): +With the implementation of Rev3 you need to specify the Rev you want to build. +To build for a Rev2 with a default keymap: - make xd60:default +```make xd60/rev2:default``` -See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. +To build for a Rev3 with a default keymap: + +```make xd60/rev3:default``` + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/xd60/rev2/config.h b/keyboards/xd60/rev2/config.h new file mode 100644 index 000000000..6c447b89f --- /dev/null +++ b/keyboards/xd60/rev2/config.h @@ -0,0 +1,74 @@ +/* +Copyright 2012 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER XIUDI +#define PRODUCT XD60v2 +#define DESCRIPTION XD60 v2 Keyboard PCB by XIUDI + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* Backlight Setup */ +#define BACKLIGHT_PIN F5 +#define BACKLIGHT_LEVELS 6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* RGB Underglow + * F6 PIN for XD60v2 that has pre-soldered WS2812 LEDs + */ +#define RGB_DI_PIN F6 +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 6 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +#endif diff --git a/keyboards/xd60/rev2/rules.mk b/keyboards/xd60/rev2/rules.mk new file mode 100644 index 000000000..8a60252dc --- /dev/null +++ b/keyboards/xd60/rev2/rules.mk @@ -0,0 +1,67 @@ +# MCU name +# MCU = at90usb1287 +MCU = atmega32u4 + + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# LUFA specific +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +LAYOUTS = 60_ansi \ No newline at end of file diff --git a/keyboards/xd60/rev3/config.h b/keyboards/xd60/rev3/config.h new file mode 100644 index 000000000..d88330cf7 --- /dev/null +++ b/keyboards/xd60/rev3/config.h @@ -0,0 +1,71 @@ +/* +Copyright 2019 Rodrigo Feijao + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6363 +#define DEVICE_VER 0x0001 +#define MANUFACTURER XIUDI +#define PRODUCT XD60rev3 +#define DESCRIPTION XD60 rev3 Keyboard PCB by XIUDI + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* Backlight Setup */ +#define BACKLIGHT_PIN F5 +#define BACKLIGHT_LEVELS 6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* RGB Underglow + * F6 PIN for XD60v3 that has pre-soldered LEDs + */ +#define RGB_DI_PIN F6 +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 12 +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE diff --git a/keyboards/xd60/rev3/rules.mk b/keyboards/xd60/rev3/rules.mk new file mode 100644 index 000000000..f33fff76c --- /dev/null +++ b/keyboards/xd60/rev3/rules.mk @@ -0,0 +1,67 @@ +# MCU name +# MCU = at90usb1287 +MCU = atmega32u4 + + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# LUFA specific +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +BOOTLOADER = atmel-dfu + + +# Build Options +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +LAYOUTS = 60_ansi diff --git a/keyboards/xd60/rules.mk b/keyboards/xd60/rules.mk deleted file mode 100644 index 8a60252dc..000000000 --- a/keyboards/xd60/rules.mk +++ /dev/null @@ -1,67 +0,0 @@ -# MCU name -# MCU = at90usb1287 -MCU = atmega32u4 - - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# LUFA specific -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = no # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - -LAYOUTS = 60_ansi \ No newline at end of file -- cgit v1.2.3