diff options
Diffstat (limited to 'keyboards/cannonkeys/ortho75')
6 files changed, 6 insertions, 320 deletions
diff --git a/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.c b/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.c deleted file mode 100644 index 8c5a87f35..000000000 --- a/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.c +++ /dev/null @@ -1,56 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#include "hal.h" - -// Value to place in RTC backup register 10 for persistent bootloader mode -#define RTC_BOOTLOADER_FLAG 0x424C - -/** - * @brief PAL setup. - * @details Digital I/O ports static configuration as defined in @p board.h. - * This variable is used by the HAL when initializing the PAL driver. - */ -#if HAL_USE_PAL || defined(__DOXYGEN__) -const PALConfig pal_default_config = -{ - {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, - {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, - {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, - {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, - {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, -}; -#endif - -/* - * Early initialization code. - * This initialization must be performed just after stack setup and before - * any other initialization. - */ -void __early_init(void) { - - stm32_clock_init(); -} - -/* - * Board-specific initialization code. - */ -void boardInit(void) { - //JTAG-DP Disabled and SW-DP Enabled - AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE; - //Set backup register DR10 to enter bootloader on reset - BKP->DR10 = RTC_BOOTLOADER_FLAG; -} diff --git a/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.h b/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.h deleted file mode 100644 index 9427adabf..000000000 --- a/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.h +++ /dev/null @@ -1,166 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#ifndef _BOARD_H_ -#define _BOARD_H_ - -/* - * Setup for a Generic STM32F103 board. - */ - -/* - * Board identifier. - */ -#define BOARD_GENERIC_STM32_F103 -#define BOARD_NAME "Generic STM32F103x board" - -/* - * Board frequencies. - */ -#define STM32_LSECLK 32768 -#define STM32_HSECLK 8000000 - -/* - * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. - */ -#define STM32F103xB - -/* - * IO pins assignments - */ - -/* on-board */ - -#define GPIOA_LED 8 -#define GPIOD_OSC_IN 0 -#define GPIOD_OSC_OUT 1 - -/* In case your board has a "USB enable" hardware - controlled by a pin, define it here. (It could be just - a 1.5k resistor connected to D+ line.) -*/ -/* -#define GPIOB_USB_DISC 10 -*/ - -/* - * I/O ports initial setup, this configuration is established soon after reset - * in the initialization code. - * - * The digits have the following meaning: - * 0 - Analog input. - * 1 - Push Pull output 10MHz. - * 2 - Push Pull output 2MHz. - * 3 - Push Pull output 50MHz. - * 4 - Digital input. - * 5 - Open Drain output 10MHz. - * 6 - Open Drain output 2MHz. - * 7 - Open Drain output 50MHz. - * 8 - Digital input with PullUp or PullDown resistor depending on ODR. - * 9 - Alternate Push Pull output 10MHz. - * A - Alternate Push Pull output 2MHz. - * B - Alternate Push Pull output 50MHz. - * C - Reserved. - * D - Alternate Open Drain output 10MHz. - * E - Alternate Open Drain output 2MHz. - * F - Alternate Open Drain output 50MHz. - * Please refer to the STM32 Reference Manual for details. - */ - -/* - * Port A setup. - * Everything input with pull-up except: - * PA2 - Alternate output (USART2 TX). - * PA3 - Normal input (USART2 RX). - * PA9 - Alternate output (USART1 TX). - * PA10 - Normal input (USART1 RX). - */ -#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ -#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ -#define VAL_GPIOAODR 0xFFFFFFFF - -/* - * Port B setup. - * Everything input with pull-up except: - * PB10 - Push Pull output (USB switch). - */ -#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ -#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ -#define VAL_GPIOBODR 0xFFFFFFFF - -/* - * Port C setup. - * Everything input with pull-up except: - * PC13 - Push Pull output (LED). - */ -#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ -#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ -#define VAL_GPIOCODR 0xFFFFFFFF - -/* - * Port D setup. - * Everything input with pull-up except: - * PD0 - Normal input (XTAL). - * PD1 - Normal input (XTAL). - */ -#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ -#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ -#define VAL_GPIODODR 0xFFFFFFFF - -/* - * Port E setup. - * Everything input with pull-up except: - */ -#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ -#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ -#define VAL_GPIOEODR 0xFFFFFFFF - -/* - * USB bus activation macro, required by the USB driver. - */ -/* The point is that most of the generic STM32F103* boards - have a 1.5k resistor connected on one end to the D+ line - and on the other end to some pin. Or even a slightly more - complicated "USB enable" circuit, controlled by a pin. - That should go here. - - However on some boards (e.g. one that I have), there's no - such hardware. In which case it's better to not do anything. -*/ -/* -#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) -*/ -#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); - -/* - * USB bus de-activation macro, required by the USB driver. - */ -/* -#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) -*/ -#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); - -#if !defined(_FROM_ASM_) -#ifdef __cplusplus -extern "C" { -#endif - void boardInit(void); -#ifdef __cplusplus -} -#endif -#endif /* _FROM_ASM_ */ - -#endif /* _BOARD_H_ */ diff --git a/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.mk b/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.mk deleted file mode 100644 index 6b8b312fd..000000000 --- a/keyboards/cannonkeys/ortho75/boards/GENERIC_STM32_F103/board.mk +++ /dev/null @@ -1,5 +0,0 @@ -# List of all the board related files. -BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c - -# Required include directories -BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103 diff --git a/keyboards/cannonkeys/ortho75/chconf.h b/keyboards/cannonkeys/ortho75/chconf.h index bbd9b2da6..9299be587 100644 --- a/keyboards/cannonkeys/ortho75/chconf.h +++ b/keyboards/cannonkeys/ortho75/chconf.h @@ -105,10 +105,6 @@ */ #define CH_CFG_NO_IDLE_THREAD FALSE -/* Use __WFI in the idle thread for waiting. Does lower the power - * consumption. */ -#define CORTEX_ENABLE_WFI_IDLE TRUE - /** @} */ /*===========================================================================*/ diff --git a/keyboards/cannonkeys/ortho75/ld/STM32F103x8_stm32duino_bootloader.ld b/keyboards/cannonkeys/ortho75/ld/STM32F103x8_stm32duino_bootloader.ld deleted file mode 100644 index d0688ef60..000000000 --- a/keyboards/cannonkeys/ortho75/ld/STM32F103x8_stm32duino_bootloader.ld +++ /dev/null @@ -1,88 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -/* - * ST32F103xB memory setup for use with the maplemini bootloader. - * You will have to - * #define CORTEX_VTOR_INIT 0x5000 - * in your projects chconf.h - */ -MEMORY -{ - flash0 : org = 0x08002000, len = 64k - 0x2000 - flash1 : org = 0x00000000, len = 0 - flash2 : org = 0x00000000, len = 0 - flash3 : org = 0x00000000, len = 0 - flash4 : org = 0x00000000, len = 0 - flash5 : org = 0x00000000, len = 0 - flash6 : org = 0x00000000, len = 0 - flash7 : org = 0x00000000, len = 0 - ram0 : org = 0x20000000, len = 20k - ram1 : org = 0x00000000, len = 0 - ram2 : org = 0x00000000, len = 0 - ram3 : org = 0x00000000, len = 0 - ram4 : org = 0x00000000, len = 0 - ram5 : org = 0x00000000, len = 0 - ram6 : org = 0x00000000, len = 0 - ram7 : org = 0x00000000, len = 0 -} - -/* For each data/text section two region are defined, a virtual region - and a load region (_LMA suffix).*/ - -/* Flash region to be used for exception vectors.*/ -REGION_ALIAS("VECTORS_FLASH", flash0); -REGION_ALIAS("VECTORS_FLASH_LMA", flash0); - -/* Flash region to be used for constructors and destructors.*/ -REGION_ALIAS("XTORS_FLASH", flash0); -REGION_ALIAS("XTORS_FLASH_LMA", flash0); - -/* Flash region to be used for code text.*/ -REGION_ALIAS("TEXT_FLASH", flash0); -REGION_ALIAS("TEXT_FLASH_LMA", flash0); - -/* Flash region to be used for read only data.*/ -REGION_ALIAS("RODATA_FLASH", flash0); -REGION_ALIAS("RODATA_FLASH_LMA", flash0); - -/* Flash region to be used for various.*/ -REGION_ALIAS("VARIOUS_FLASH", flash0); -REGION_ALIAS("VARIOUS_FLASH_LMA", flash0); - -/* Flash region to be used for RAM(n) initialization data.*/ -REGION_ALIAS("RAM_INIT_FLASH_LMA", flash0); - -/* RAM region to be used for Main stack. This stack accommodates the processing - of all exceptions and interrupts.*/ -REGION_ALIAS("MAIN_STACK_RAM", ram0); - -/* RAM region to be used for the process stack. This is the stack used by - the main() function.*/ -REGION_ALIAS("PROCESS_STACK_RAM", ram0); - -/* RAM region to be used for data segment.*/ -REGION_ALIAS("DATA_RAM", ram0); -REGION_ALIAS("DATA_RAM_LMA", flash0); - -/* RAM region to be used for BSS segment.*/ -REGION_ALIAS("BSS_RAM", ram0); - -/* RAM region to be used for the default heap.*/ -REGION_ALIAS("HEAP_RAM", ram0); - -/* Generic rules inclusion.*/ -INCLUDE rules.ld diff --git a/keyboards/cannonkeys/ortho75/rules.mk b/keyboards/cannonkeys/ortho75/rules.mk index 5b90e87fd..3be309924 100644 --- a/keyboards/cannonkeys/ortho75/rules.mk +++ b/keyboards/cannonkeys/ortho75/rules.mk @@ -4,7 +4,7 @@ MCU = STM32F103 # GENERIC STM32F103C8T6 board - stm32duino bootloader OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000 MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader -BOARD = GENERIC_STM32_F103 +BOARD = STM32_F103_STM32DUINO DFU_ARGS = -d 1eaf:0003 -a2 -R DFU_SUFFIX_ARGS = -v 1eaf -p 0003 @@ -22,7 +22,12 @@ COMMAND_ENABLE = yes # Commands for debug and configuration SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend NKRO_ENABLE = yes # USB Nkey Rollover BACKLIGHT_ENABLE = yes +BACKLIGHT_DRIVER = custom RGBLIGHT_ENABLE = yes ENCODER_ENABLE = yes LAYOUTS = ortho_5x15 + + +# Enter lower-power sleep mode when on the ChibiOS idle thread +OPT_DEFS += -DCORTEX_ENABLE_WFI_IDLE=TRUE |