/*
    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

/**
 * @defgroup LPC13xx LPC13xx Drivers
 * @details This section describes all the supported drivers on the LPC13xx
 *          platform and the implementation details of the single drivers.
 *
 * @ingroup platforms
 */

/**
 * @defgroup LPC13xx_HAL LPC13xx Initialization Support
 * @details The LPC13xx HAL support is responsible for system initialization.
 *
 * @section lpc13xx_hal_1 Supported HW resources
 * - SYSCON.
 * - Flash.
 * .
 * @section lpc13xx_hal_2 LPC13xx HAL driver implementation features
 * - Clock tree initialization.
 * - Clock source selection.
 * - Flash controller initialization.
 * - SYSTICK initialization based on current clock and kernel required rate.
 * .
 * @ingroup LPC13xx
 */

/**
 * @defgroup LPC13xx_GPT LPC13xx GPT Support
 * @details The LPC13xx GPT driver uses the CTxxBy peripherals.
 *
 * @section lpc13xx_gpt_1 Supported HW resources
 * - CT16B0.
 * - CT16B1.
 * - CT32B0.
 * - CT32B1.
 * .
 * @section lpc13xx_gpt_2 LPC13xx GPT driver implementation features
 * - Each timer can be independently enabled and programmed. Unused
 *   peripherals are left in low power mode.
 * - Programmable CTxxBy interrupts priority level.
 * .
 * @ingroup LPC13xx
 */

/**
 * @defgroup LPC13xx_PAL LPC13xx PAL Support
 * @details The LPC13xx PAL driver uses the GPIO peripherals.
 *
 * @section lpc13xx_pal_1 Supported HW resources
 * - GPIO0.
 * - GPIO1.
 * - GPIO2.
 * - GPIO3.
 * .
 * @section lpc13xx_pal_2 LPC13xx PAL driver implementation features
 * - 12 bits wide ports.
 * - Atomic set/reset functions.
 * - Atomic set+reset function (atomic bus operations).
 * - Output latched regardless of the pad setting.
 * - Direct read of input pads regardless of the pad setting.
 * .
 * @section lpc13xx_pal_3 Supported PAL setup modes
 * - @p PAL_MODE_RESET.
 * - @p PAL_MODE_UNCONNECTED.
 * - @p PAL_MODE_INPUT.
 * - @p PAL_MODE_OUTPUT_PUSHPULL.
 * .
 * Any attempt to setup an invalid mode is ignored.
 *
 * @section lpc13xx_pal_4 Suboptimal behavior
 * Some GPIO features are less than optimal:
 * - Pad/port toggling operations are not atomic.
 * - Pull-up and Pull-down resistors cannot be programmed through the PAL
 *   driver and must be programmed separately using the IOCON peripheral.
 * - Reading of the output latch for pads programmed as input is not possible,
 *   the input pin value is returned instead.
 * .
 * @ingroup LPC13xx
 */

/**
 * @defgroup LPC13xx_SERIAL LPC13xx Serial Support
 * @details The LPC13xx Serial driver uses the UART peripheral in a
 *          buffered, interrupt driven, implementation. The serial driver
 *          also takes advantage of the LPC13xx UARTs deep hardware buffers.
 *
 * @section lpc13xx_serial_1 Supported HW resources
 * The serial driver can support any of the following hardware resources:
 * - UART.
 * .
 * @section lpc13xx_serial_2 LPC13xx Serial driver implementation features
 * - Clock stop for reduced power usage when the driver is in stop state.
 * - Fully interrupt driven.
 * - Programmable priority level.
 * - Takes advantage of the input and output FIFOs.
 * .
 * @ingroup LPC13xx
 */

/**
 * @defgroup LPC13xx_SPI LPC13xx SPI Support
 * @details The SPI driver supports the LPC13xx SSP peripherals in an interrupt
 *          driven implementation.
 * @note    Being the SPI a fast peripheral, much care must be taken to
 *          not saturate the CPU bandwidth with an excessive IRQ rate. The
 *          maximum transfer bit rate is likely limited by the IRQ
 *          handling.
 *
 * @section lpc13xx_spi_1 Supported HW resources
 * - SSP0.
 * - SSP1 (where present).
 * .
 * @section lpc13xx_spi_2 LPC13xx SPI driver implementation features
 * - Clock stop for reduced power usage when the driver is in stop state.
 * - Each SSP can be independently enabled and programmed. Unused
 *   peripherals are left in low power mode.
 * - Fully interrupt driven.
 * - Programmable interrupt priority levels for each SSP.
 * .
 * @ingroup LPC13xx
 */