/*
    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

#ifndef _BOARD_H_
#define _BOARD_H_

/*
 * Setup for Embedded Artists LPCXpresso LPC812 board.
 */

/*
 * Board identifiers.
 */
#define BOARD_EA_LPC812
#define BOARD_NAME "Embedded Artists LPCXpresso LPC812"

/*
 * Board frequencies.
 */
#define SYSOSCCLK               12000000


/*
 * I/O ports initial setup, this configuration is established soon after reset
 * in the initialization code.
 * Please refer to the LPC8xx Reference Manual for details.
 */
/* Pull-up/down  */
#define PIN_MODE_NOPULL               (0<<3)
#define PIN_MODE_PULLDOWN             (1<<3)
#define PIN_MODE_PULLUP               (2<<3)
#define PIN_MODE_REPEATER             (3<<3)
/* Hysteresis */
#define PIN_HYS_EN                    (1<<5)
/* Invert Input */
#define PIN_INV_INPUT                 (1<<6)
/* Reserved bits */
#define PIN_RSVD                      (1<<7)
/* I2C Mode */
#define PIN_I2CMODE_STD               (0<<8)
#define PIN_I2CMODE_STDIO             (1<<8)
#define PIN_I2CMODE_FAST              (2<<8)
/* Open Drain */
#define PIN_OPEN_DRAIN                (1<<10)
/* Input Filter Sample Clocks */
#define PIN_SMODE_FILTER(n)           ((n)<<11)
/* Input Filter clock divider */
#define PIN_CLKDIV_FILTER(n)          ((n)<<13)

/*
 * Pin definitions.
 */
#define LED_RED                        7
#define LED_BLUE                      16
#define LED_GREEN                     17


/*
 * GPIO 0 initial setup.
 */
/*#define VAL_PIO0_0              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_1              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_2              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_3              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_4              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_5              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_6              PIN_MODE_PULLUP*/
#define VAL_PIO0_7              PIN_MODE_NOPULL
/*#define VAL_PIO0_8              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_9              PIN_MODE_PULLUP*/
/*#define VAL_PIO0_10             PIN_MODE_PULLUP*/
/*#define VAL_PIO0_11             PIN_MODE_PULLUP*/
/*#define VAL_PIO0_12             PIN_MODE_PULLUP*/
/*#define VAL_PIO0_13             PIN_MODE_PULLUP*/
/*#define VAL_PIO0_14             PIN_MODE_PULLUP*/
/*#define VAL_PIO0_15             PIN_MODE_PULLUP*/
#define VAL_PIO0_16             PIN_MODE_NOPULL
#define VAL_PIO0_17             PIN_MODE_NOPULL

    /* UART0: TXD = P0.4, RXD  = P0.0)*/
#define VAL_PINASSIGN0            ((0xFFFF0000) | (0<<8) | (4))
/*#define VAL_PINASSIGN1            0xFFFFFFFF*/
/*#define VAL_PINASSIGN2            0xFFFFFFFF*/
/*#define VAL_PINASSIGN3            0xFFFFFFFF*/
/*#define VAL_PINASSIGN4            0xFFFFFFFF*/
/*#define VAL_PINASSIGN5            0xFFFFFFFF*/
/*#define VAL_PINASSIGN6            0xFFFFFFFF*/
/*#define VAL_PINASSIGN7            0xFFFFFFFF*/
/*#define VAL_PINASSIGN8            0xFFFFFFFF*/


#define VAL_GPIO0DIR            (PAL_PORT_BIT(LED_RED)   |           \
                                 PAL_PORT_BIT(LED_BLUE)   |          \
                                 PAL_PORT_BIT(LED_GREEN))
                                
#define VAL_GPIO0DATA           (PAL_PORT_BIT(LED_RED)   |           \
                                 PAL_PORT_BIT(LED_BLUE)   |          \
                                 PAL_PORT_BIT(LED_GREEN))


#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
  void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */


#endif /* _BOARD_H_ */