From e0b177423e1b14ab942fbf40b79d60d13ae02eb5 Mon Sep 17 00:00:00 2001 From: gdisirio Date: Tue, 15 May 2012 17:01:41 +0000 Subject: Initial STM32F0xx support. git-svn-id: svn://svn.code.sf.net/p/chibios/svn/trunk@4198 35acf78f-673a-0410-8e92-d51de3d6d3f4 --- os/hal/platforms/STM32F0xx/stm32f0xx.h | 3220 ++++++++++++++++++++++++++++++++ 1 file changed, 3220 insertions(+) create mode 100644 os/hal/platforms/STM32F0xx/stm32f0xx.h (limited to 'os/hal/platforms') diff --git a/os/hal/platforms/STM32F0xx/stm32f0xx.h b/os/hal/platforms/STM32F0xx/stm32f0xx.h new file mode 100644 index 000000000..07c252c11 --- /dev/null +++ b/os/hal/platforms/STM32F0xx/stm32f0xx.h @@ -0,0 +1,3220 @@ +/** + ****************************************************************************** + * @file stm32f0xx.h + * @author MCD Application Team + * @version V1.0.0 + * @date 23-March-2012 + * @brief CMSIS Cortex-M0 Device Peripheral Access Layer Header File. + * This file contains all the peripheral register's definitions, bits + * definitions and memory mapping for STM32F0xx devices. + * + * The file is the unique include file that the application programmer + * is using in the C source code, usually in main.c. This file contains: + * - Configuration section that allows to select: + * - The device used in the target application + * - To use or not the peripheral’s drivers in application code(i.e. + * code will be based on direct access to peripheral’s registers + * rather than drivers API), this option is controlled by + * "#define USE_STDPERIPH_DRIVER" + * - To change few application-specific parameters such as the HSE + * crystal frequency + * - Data structures and the address mapping for all peripherals + * - Peripheral's registers declarations and bits definition + * - Macros to access peripheral’s registers hardware + * + ****************************************************************************** + * @attention + * + *

© COPYRIGHT 2012 STMicroelectronics

+ * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f0xx + * @{ + */ + +#ifndef __STM32F0XX_H +#define __STM32F0XX_H + +#ifdef __cplusplus + extern "C" { +#endif + +/** @addtogroup Library_configuration_section + * @{ + */ + +/* Uncomment the line below according to the target STM32F-0 device used in your + application + */ + +#if !defined (STM32F0XX) + #define STM32F0XX /*!< STM32F0XX: STM32F0xx devices */ +#endif +/* Tip: To avoid modifying this file each time you need to switch between these + devices, you can define the device in your toolchain compiler preprocessor. + + - STM32F0xx devices are STM32F050xx microcontrollers where the Flash memory + density ranges between 32 and 64 Kbytes. + */ + +#if !defined (STM32F0XX) + #error "Please select first the target STM32F0xx device used in your application (in stm32f0xx.h file)" +#endif /* STM32F0XX */ + +#if !defined USE_STDPERIPH_DRIVER +/** + * @brief Comment the line below if you will not use the peripherals drivers. + In this case, these drivers will not be included and the application code will + be based on direct access to peripherals registers + */ + /*#define USE_STDPERIPH_DRIVER*/ +#endif /* USE_STDPERIPH_DRIVER */ + +/** + * @brief In the following line adjust the value of External High Speed oscillator (HSE) + used in your application + + Tip: To avoid modifying this file each time you need to use different HSE, you + can define the HSE value in your toolchain compiler preprocessor. + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz*/ +#endif /* HSE_VALUE */ + +/** + * @brief In the following line adjust the External High Speed oscillator (HSE) Startup + Timeout value + */ +#if !defined (HSE_STARTUP_TIMEOUT) +#define HSE_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSE start up */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup + Timeout value + */ +#if !defined (HSI_STARTUP_TIMEOUT) +#define HSI_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSI start up */ +#endif /* HSI_STARTUP_TIMEOUT */ + +#if !defined (HSI_VALUE) +#define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal High Speed oscillator in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI_VALUE */ + +#if !defined (HSI14_VALUE) +#define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI14_VALUE */ + +#if !defined (LSI_VALUE) +#define LSI_VALUE ((uint32_t)40000) /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* LSI_VALUE */ + +#if !defined (LSE_VALUE) +#define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +/** + * @brief STM32F0xx Standard Peripheral Library version number V1.0.0 + */ +#define __STM32F0XX_STDPERIPH_VERSION_MAIN (0x01) /*!< [31:24] main version */ +#define __STM32F0XX_STDPERIPH_VERSION_SUB1 (0x00) /*!< [23:16] sub1 version */ +#define __STM32F0XX_STDPERIPH_VERSION_SUB2 (0x00) /*!< [15:8] sub2 version */ +#define __STM32F0XX_STDPERIPH_VERSION_RC (0x00) /*!< [7:0] release candidate */ +#define __STM32F0XX_STDPERIPH_VERSION ((__STM32F0XX_STDPERIPH_VERSION_MAIN << 24)\ + |(__STM32F0XX_STDPERIPH_VERSION_SUB1 << 16)\ + |(__STM32F0XX_STDPERIPH_VERSION_SUB2 << 8)\ + |(__STM32F0XX_STDPERIPH_VERSION_RC)) + +/** + * @} + */ + +/** @addtogroup Configuration_section_for_CMSIS + * @{ + */ + +/** + * @brief STM32F0xx Interrupt Number Definition, according to the selected device + * in @ref Library_configuration_section + */ +#define __CM0_REV 0 /*!< Core Revision r0p0 */ +#define __MPU_PRESENT 0 /*!< STM32F0xx do not provide MPU */ +#define __NVIC_PRIO_BITS 2 /*!< STM32F0xx uses 2 Bits for the Priority Levels */ +#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */ + +/*!< Interrupt Number Definition */ +typedef enum IRQn +{ +/****** Cortex-M0 Processor Exceptions Numbers ******************************************************/ + NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ + HardFault_IRQn = -13, /*!< 3 Cortex-M0 Hard Fault Interrupt */ + SVC_IRQn = -5, /*!< 11 Cortex-M0 SV Call Interrupt */ + PendSV_IRQn = -2, /*!< 14 Cortex-M0 Pend SV Interrupt */ + SysTick_IRQn = -1, /*!< 15 Cortex-M0 System Tick Interrupt */ + +/****** STM32F-0 specific Interrupt Numbers *********************************************************/ + WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ + PVD_IRQn = 1, /*!< PVD through EXTI Line detect Interrupt */ + RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */ + FLASH_IRQn = 3, /*!< FLASH Interrupt */ + RCC_IRQn = 4, /*!< RCC Interrupt */ + EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */ + EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */ + EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */ + TS_IRQn = 8, /*!< TS Interrupt */ + DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */ + DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */ + DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */ + ADC1_COMP_IRQn = 12, /*!< ADC1, COMP1 and COMP2 Interrupts */ + TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */ + TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */ + TIM2_IRQn = 15, /*!< TIM2 Interrupt */ + TIM3_IRQn = 16, /*!< TIM3 Interrupt */ + TIM6_DAC_IRQn = 17, /*!< TIM6 and DAC Interrupts */ + TIM14_IRQn = 19, /*!< TIM14 Interrupt */ + TIM15_IRQn = 20, /*!< TIM15 Interrupt */ + TIM16_IRQn = 21, /*!< TIM16 Interrupt */ + TIM17_IRQn = 22, /*!< TIM17 Interrupt */ + I2C1_IRQn = 23, /*!< I2C1 Interrupt */ + I2C2_IRQn = 24, /*!< I2C2 Interrupt */ + SPI1_IRQn = 25, /*!< SPI1 Interrupt */ + SPI2_IRQn = 26, /*!< SPI2 Interrupt */ + USART1_IRQn = 27, /*!< USART1 Interrupt */ + USART2_IRQn = 28, /*!< USART2 Interrupt */ + CEC_IRQn = 30 /*!< CEC Interrupt */ +} IRQn_Type; + +/** + * @} + */ + +#include "core_cm0.h" +#include "system_stm32f0xx.h" +#include + +/** @addtogroup Exported_types + * @{ + */ + +typedef enum {RESET = 0, SET = !RESET} FlagStatus, ITStatus; + +typedef enum {DISABLE = 0, ENABLE = !DISABLE} FunctionalState; +#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE)) + +typedef enum {ERROR = 0, SUCCESS = !ERROR} ErrorStatus; + +/** @addtogroup Peripheral_registers_structures + * @{ + */ + +/** + * @brief Analog to Digital Converter + */ + +typedef struct +{ + __IO uint32_t ISR; /*!< ADC Interrupt and Status register, Address offset:0x00 */ + __IO uint32_t IER; /*!< ADC Interrupt Enable register, Address offset:0x04 */ + __IO uint32_t CR; /*!< ADC Control register, Address offset:0x08 */ + __IO uint32_t CFGR1; /*!< ADC Configuration register 1, Address offset:0x0C */ + __IO uint32_t CFGR2; /*!< ADC Configuration register 2, Address offset:0x10 */ + __IO uint32_t SMPR; /*!< ADC Sampling time register, Address offset:0x14 */ + uint32_t RESERVED1; /*!< Reserved, 0x18 */ + uint32_t RESERVED2; /*!< Reserved, 0x1C */ + __IO uint32_t TR; /*!< ADC watchdog threshold register, Address offset:0x20 */ + uint32_t RESERVED3; /*!< Reserved, 0x24 */ + __IO uint32_t CHSELR; /*!< ADC channel selection register, Address offset:0x28 */ + uint32_t RESERVED4[5]; /*!< Reserved, 0x2C */ + __IO uint32_t DR; /*!< ADC data register, Address offset:0x40 */ +} ADC_TypeDef; + +typedef struct +{ + __IO uint32_t CCR; +} ADC_Common_TypeDef; + +/** + * @brief HDMI-CEC + */ + +typedef struct +{ + __IO uint32_t CR; /*!< CEC control register, Address offset:0x00 */ + __IO uint32_t CFGR; /*!< CEC configuration register, Address offset:0x04 */ + __IO uint32_t TXDR; /*!< CEC Tx data register , Address offset:0x08 */ + __IO uint32_t RXDR; /*!< CEC Rx Data Register, Address offset:0x0C */ + __IO uint32_t ISR; /*!< CEC Interrupt and Status Register, Address offset:0x10 */ + __IO uint32_t IER; /*!< CEC interrupt enable register, Address offset:0x14 */ +}CEC_TypeDef; + +/** + * @brief Comparator + */ + +typedef struct +{ + __IO uint32_t CSR; /*!< COMP comparator control and status register, Address offset: 0x1C */ +} COMP_TypeDef; + + +/** + * @brief CRC calculation unit + */ + +typedef struct +{ + __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ + __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ + uint8_t RESERVED0; /*!< Reserved, 0x05 */ + uint16_t RESERVED1; /*!< Reserved, 0x06 */ + __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ + uint32_t RESERVED2; /*!< Reserved, 0x0C */ + __IO uint32_t INIT; /*!< Initial CRC value register, Address offset: 0x10 */ +} CRC_TypeDef; + + +/** + * @brief Digital to Analog Converter + */ + +typedef struct +{ + __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ + __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ + __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ + __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ + __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ + uint32_t RESERVED[6]; /*!< Reserved, 0x14 */ + __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ + uint32_t RESERVED1; /*!< Reserved, 0x30 */ + __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ +} DAC_TypeDef; + +/** + * @brief Debug MCU + */ + +typedef struct +{ + __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ + __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ + __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ + __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ +}DBGMCU_TypeDef; + +/** + * @brief DMA Controller + */ + +typedef struct +{ + __IO uint32_t CCR; /*!< DMA channel x configuration register */ + __IO uint32_t CNDTR; /*!< DMA channel x number of data register */ + __IO uint32_t CPAR; /*!< DMA channel x peripheral address register */ + __IO uint32_t CMAR; /*!< DMA channel x memory address register */ +} DMA_Channel_TypeDef; + +typedef struct +{ + __IO uint32_t ISR; /*!< DMA interrupt status register, Address offset: 0x00 */ + __IO uint32_t IFCR; /*!< DMA interrupt flag clear register, Address offset: 0x04 */ +} DMA_TypeDef; + +/** + * @brief External Interrupt/Event Controller + */ + +typedef struct +{ + __IO uint32_t IMR; /*!