From 95583e02d4d82a916efb735bd2acfb4a70599ed7 Mon Sep 17 00:00:00 2001 From: Giovanni Di Sirio Date: Sun, 8 Oct 2017 16:56:44 +0000 Subject: Grouped configuration files, too many of them. git-svn-id: svn://svn.code.sf.net/p/chibios/svn/trunk@10800 35acf78f-673a-0410-8e92-d51de3d6d3f4 --- .../Makefile | 7 +- .../chconf.h | 582 ------ .../ffconf.h | 272 --- .../halconf.h | 395 ---- .../httpd_opts.h | 323 --- .../lwipopts.h | 2127 -------------------- .../mcuconf.h | 391 ---- .../usbcfg.c | 342 ---- .../usbcfg.h | 26 - 9 files changed, 5 insertions(+), 4460 deletions(-) delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/chconf.h delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/ffconf.h delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/halconf.h delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/httpd_opts.h delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/lwipopts.h delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/mcuconf.h delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.c delete mode 100644 demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.h diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/Makefile b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/Makefile index 4323d9cb9..72bdc14b9 100644 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/Makefile +++ b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/Makefile @@ -89,6 +89,9 @@ endif # Define project name here PROJECT = ch +CONFDIR := ./cfg +BUILDDIR := ./build +DEPDIR := ./.dep # Imported source files and paths CHIBIOS = ../../.. @@ -127,7 +130,7 @@ CSRC = $(STARTUPSRC) \ $(STREAMSSRC) \ $(SHELLSRC) \ $(CHIBIOS)/os/various/evtimer.c \ - usbcfg.c main.c + src/usbcfg.c main.c # C++ sources that can be compiled in ARM or THUMB mode depending on the global # setting. @@ -161,7 +164,7 @@ INCDIR = $(CHIBIOS)/os/license \ $(STARTUPINC) $(KERNINC) $(PORTINC) $(OSALINC) \ $(HALINC) $(PLATFORMINC) $(BOARDINC) $(TESTINC) \ $(STREAMSINC) $(SHELLINC) $(LWINC) $(FATFSINC) \ - $(CHIBIOS)/os/various + $(CHIBIOS)/os/various $(CONFDIR) ./src # # Project, sources and paths diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/chconf.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/chconf.h deleted file mode 100644 index 0a4ea73a6..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/chconf.h +++ /dev/null @@ -1,582 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -/** - * @file templates/chconf.h - * @brief Configuration file template. - * @details A copy of this file must be placed in each project directory, it - * contains the application specific kernel settings. - * - * @addtogroup config - * @details Kernel related settings and hooks. - * @{ - */ - -#ifndef CHCONF_H -#define CHCONF_H - -#define _CHIBIOS_RT_CONF_ -#define _CHIBIOS_RT_CONF_VER_5_0_ - -/*===========================================================================*/ -/** - * @name System timers settings - * @{ - */ -/*===========================================================================*/ - -/** - * @brief System time counter resolution. - * @note Allowed values are 16 or 32 bits. - */ -#define CH_CFG_ST_RESOLUTION 32 - -/** - * @brief System tick frequency. - * @details Frequency of the system timer that drives the system ticks. This - * setting also defines the system tick time unit. - */ -#define CH_CFG_ST_FREQUENCY 10000 - -/** - * @brief Time delta constant for the tick-less mode. - * @note If this value is zero then the system uses the classic - * periodic tick. This value represents the minimum number - * of ticks that is safe to specify in a timeout directive. - * The value one is not valid, timeouts are rounded up to - * this value. - */ -#define CH_CFG_ST_TIMEDELTA 2 - -/** @} */ - -/*===========================================================================*/ -/** - * @name Kernel parameters and options - * @{ - */ -/*===========================================================================*/ - -/** - * @brief Round robin interval. - * @details This constant is the number of system ticks allowed for the - * threads before preemption occurs. Setting this value to zero - * disables the preemption for threads with equal priority and the - * round robin becomes cooperative. Note that higher priority - * threads can still preempt, the kernel is always preemptive. - * @note Disabling the round robin preemption makes the kernel more compact - * and generally faster. - * @note The round robin preemption is not supported in tickless mode and - * must be set to zero in that case. - */ -#define CH_CFG_TIME_QUANTUM 0 - -/** - * @brief Managed RAM size. - * @details Size of the RAM area to be managed by the OS. If set to zero - * then the whole available RAM is used. The core memory is made - * available to the heap allocator and/or can be used directly through - * the simplified core memory allocator. - * - * @note In order to let the OS manage the whole RAM the linker script must - * provide the @p __heap_base__ and @p __heap_end__ symbols. - * @note Requires @p CH_CFG_USE_MEMCORE. - */ -#define CH_CFG_MEMCORE_SIZE 0 - -/** - * @brief Idle thread automatic spawn suppression. - * @details When this option is activated the function @p chSysInit() - * does not spawn the idle thread. The application @p main() - * function becomes the idle thread and must implement an - * infinite loop. - */ -#define CH_CFG_NO_IDLE_THREAD FALSE - -/** @} */ - -/*===========================================================================*/ -/** - * @name Performance options - * @{ - */ -/*===========================================================================*/ - -/** - * @brief OS optimization. - * @details If enabled then time efficient rather than space efficient code - * is used when two possible implementations exist. - * - * @note This is not related to the compiler optimization options. - * @note The default is @p TRUE. - */ -#define CH_CFG_OPTIMIZE_SPEED TRUE - -/** @} */ - -/*===========================================================================*/ -/** - * @name Subsystem options - * @{ - */ -/*===========================================================================*/ - -/** - * @brief Time Measurement APIs. - * @details If enabled then the time measurement APIs are included in - * the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_TM TRUE - -/** - * @brief Threads registry APIs. - * @details If enabled then the registry APIs are included in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_REGISTRY TRUE - -/** - * @brief Threads synchronization APIs. - * @details If enabled then the @p chThdWait() function is included in - * the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_WAITEXIT TRUE - -/** - * @brief Semaphores APIs. - * @details If enabled then the Semaphores APIs are included in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_SEMAPHORES TRUE - -/** - * @brief Semaphores queuing mode. - * @details If enabled then the threads are enqueued on semaphores by - * priority rather than in FIFO order. - * - * @note The default is @p FALSE. Enable this if you have special - * requirements. - * @note Requires @p CH_CFG_USE_SEMAPHORES. - */ -#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE - -/** - * @brief Mutexes APIs. - * @details If enabled then the mutexes APIs are included in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_MUTEXES TRUE - -/** - * @brief Enables recursive behavior on mutexes. - * @note Recursive mutexes are heavier and have an increased - * memory footprint. - * - * @note The default is @p FALSE. - * @note Requires @p CH_CFG_USE_MUTEXES. - */ -#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE - -/** - * @brief Conditional Variables APIs. - * @details If enabled then the conditional variables APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - * @note Requires @p CH_CFG_USE_MUTEXES. - */ -#define CH_CFG_USE_CONDVARS TRUE - -/** - * @brief Conditional Variables APIs with timeout. - * @details If enabled then the conditional variables APIs with timeout - * specification are included in the kernel. - * - * @note The default is @p TRUE. - * @note Requires @p CH_CFG_USE_CONDVARS. - */ -#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE - -/** - * @brief Events Flags APIs. - * @details If enabled then the event flags APIs are included in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_EVENTS TRUE - -/** - * @brief Events Flags APIs with timeout. - * @details If enabled then the events APIs with timeout specification - * are included in the kernel. - * - * @note The default is @p TRUE. - * @note Requires @p CH_CFG_USE_EVENTS. - */ -#define CH_CFG_USE_EVENTS_TIMEOUT TRUE - -/** - * @brief Synchronous Messages APIs. - * @details If enabled then the synchronous messages APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_MESSAGES TRUE - -/** - * @brief Synchronous Messages queuing mode. - * @details If enabled then messages are served by priority rather than in - * FIFO order. - * - * @note The default is @p FALSE. Enable this if you have special - * requirements. - * @note Requires @p CH_CFG_USE_MESSAGES. - */ -#define CH_CFG_USE_MESSAGES_PRIORITY FALSE - -/** - * @brief Mailboxes APIs. - * @details If enabled then the asynchronous messages (mailboxes) APIs are - * included in the kernel. - * - * @note The default is @p TRUE. - * @note Requires @p CH_CFG_USE_SEMAPHORES. - */ -#define CH_CFG_USE_MAILBOXES TRUE - -/** - * @brief Core Memory Manager APIs. - * @details If enabled then the core memory manager APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_MEMCORE TRUE - -/** - * @brief Heap Allocator APIs. - * @details If enabled then the memory heap allocator APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or - * @p CH_CFG_USE_SEMAPHORES. - * @note Mutexes are recommended. - */ -#define CH_CFG_USE_HEAP TRUE - -/** - * @brief Memory Pools Allocator APIs. - * @details If enabled then the memory pools allocator APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_MEMPOOLS TRUE - -/** - * @brief Objects FIFOs APIs. - * @details If enabled then the objects FIFOs APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - */ -#define CH_CFG_USE_OBJ_FIFOS TRUE - -/** - * @brief Dynamic Threads APIs. - * @details If enabled then the dynamic threads creation APIs are included - * in the kernel. - * - * @note The default is @p TRUE. - * @note Requires @p CH_CFG_USE_WAITEXIT. - * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. - */ -#define CH_CFG_USE_DYNAMIC TRUE - -/** @} */ - -/*===========================================================================*/ -/** - * @name Objects factory options - * @{ - */ -/*===========================================================================*/ - -/** - * @brief Objects Factory APIs. - * @details If enabled then the objects factory APIs are included in the - * kernel. - * - * @note The default is @p FALSE. - */ -#define CH_CFG_USE_FACTORY TRUE - -/** - * @brief Maximum length for object names. - * @details If the specified length is zero then the name is stored by - * pointer but this could have unintended side effects. - */ -#define CH_CFG_FACTORY_MAX_NAMES_LENGTH 8 - -/** - * @brief Enables the registry of generic objects. - */ -#define CH_CFG_FACTORY_OBJECTS_REGISTRY TRUE - -/** - * @brief Enables factory for generic buffers. - */ -#define CH_CFG_FACTORY_GENERIC_BUFFERS TRUE - -/** - * @brief Enables factory for semaphores. - */ -#define CH_CFG_FACTORY_SEMAPHORES TRUE - -/** - * @brief Enables factory for mailboxes. - */ -#define CH_CFG_FACTORY_MAILBOXES TRUE - -/** - * @brief Enables factory for objects FIFOs. - */ -#define CH_CFG_FACTORY_OBJ_FIFOS TRUE - -/** @} */ - -/*===========================================================================*/ -/** - * @name Debug options - * @{ - */ -/*===========================================================================*/ - -/** - * @brief Debug option, kernel statistics. - * - * @note The default is @p FALSE. - */ -#define CH_DBG_STATISTICS FALSE - -/** - * @brief Debug option, system state check. - * @details If enabled the correct call protocol for system APIs is checked - * at runtime. - * - * @note The default is @p FALSE. - */ -#define CH_DBG_SYSTEM_STATE_CHECK FALSE - -/** - * @brief Debug option, parameters checks. - * @details If enabled then the checks on the API functions input - * parameters are activated. - * - * @note The default is @p FALSE. - */ -#define CH_DBG_ENABLE_CHECKS FALSE - -/** - * @brief Debug option, consistency checks. - * @details If enabled then all the assertions in the kernel code are - * activated. This includes consistency checks inside the kernel, - * runtime anomalies and port-defined checks. - * - * @note The default is @p FALSE. - */ -#define CH_DBG_ENABLE_ASSERTS FALSE - -/** - * @brief Debug option, trace buffer. - * @details If enabled then the trace buffer is activated. - * - * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. - */ -#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED - -/** - * @brief Trace buffer entries. - * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is - * different from @p CH_DBG_TRACE_MASK_DISABLED. - */ -#define CH_DBG_TRACE_BUFFER_SIZE 128 - -/** - * @brief Debug option, stack checks. - * @details If enabled then a runtime stack check is performed. - * - * @note The default is @p FALSE. - * @note The stack check is performed in a architecture/port dependent way. - * It may not be implemented or some ports. - * @note The default failure mode is to halt the system with the global - * @p panic_msg variable set to @p NULL. - */ -#define CH_DBG_ENABLE_STACK_CHECK FALSE - -/** - * @brief Debug option, stacks initialization. - * @details If enabled then the threads working area is filled with a byte - * value when a thread is created. This can be useful for the - * runtime measurement of the used stack. - * - * @note The default is @p FALSE. - */ -#define CH_DBG_FILL_THREADS FALSE - -/** - * @brief Debug option, threads profiling. - * @details If enabled then a field is added to the @p thread_t structure that - * counts the system ticks occurred while executing the thread. - * - * @note The default is @p FALSE. - * @note This debug option is not currently compatible with the - * tickless mode. - */ -#define CH_DBG_THREADS_PROFILING FALSE - -/** @} */ - -/*===========================================================================*/ -/** - * @name Kernel hooks - * @{ - */ -/*===========================================================================*/ - -/** - * @brief Threads descriptor structure extension. - * @details User fields added to the end of the @p thread_t structure. - */ -#define CH_CFG_THREAD_EXTRA_FIELDS \ - /* Add threads custom fields here.*/ - -/** - * @brief Threads initialization hook. - * @details User initialization code added to the @p chThdInit() API. - * - * @note It is invoked from within @p chThdInit() and implicitly from all - * the threads creation APIs. - */ -#define CH_CFG_THREAD_INIT_HOOK(tp) { \ - /* Add threads initialization code here.*/ \ -} - -/** - * @brief Threads finalization hook. - * @details User finalization code added to the @p chThdExit() API. - */ -#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ - /* Add threads finalization code here.*/ \ -} - -/** - * @brief Context switch hook. - * @details This hook is invoked just before switching between threads. - */ -#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ - /* Context switch code here.*/ \ -} - -/** - * @brief ISR enter hook. - */ -#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ - /* IRQ prologue code here.*/ \ -} - -/** - * @brief ISR exit hook. - */ -#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ - /* IRQ epilogue code here.*/ \ -} - -/** - * @brief Idle thread enter hook. - * @note This hook is invoked within a critical zone, no OS functions - * should be invoked from here. - * @note This macro can be used to activate a power saving mode. - */ -#define CH_CFG_IDLE_ENTER_HOOK() { \ - /* Idle-enter code here.*/ \ -} - -/** - * @brief Idle thread leave hook. - * @note This hook is invoked within a critical zone, no OS functions - * should be invoked from here. - * @note This macro can be used to deactivate a power saving mode. - */ -#define CH_CFG_IDLE_LEAVE_HOOK() { \ - /* Idle-leave code here.*/ \ -} - -/** - * @brief Idle Loop hook. - * @details This hook is continuously invoked by the idle thread loop. - */ -#define CH_CFG_IDLE_LOOP_HOOK() { \ - /* Idle loop code here.*/ \ -} - -/** - * @brief System tick event hook. - * @details This hook is invoked in the system tick handler immediately - * after processing the virtual timers queue. - */ -#define CH_CFG_SYSTEM_TICK_HOOK() { \ - /* System tick event code here.*/ \ -} - -/** - * @brief System halt hook. - * @details This hook is invoked in case to a system halting error before - * the system is halted. - */ -#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ - /* System halt code here.*/ \ -} - -/** - * @brief Trace hook. - * @details This hook is invoked each time a new record is written in the - * trace buffer. - */ -#define CH_CFG_TRACE_HOOK(tep) { \ - /* Trace code here.*/ \ -} - -/** @} */ - -/*===========================================================================*/ -/* Port-specific settings (override port settings defaulted in chcore.h). */ -/*===========================================================================*/ - -#define CORTEX_VTOR_INIT 0x00200000U - -#endif /* CHCONF_H */ - -/** @} */ diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/ffconf.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/ffconf.h deleted file mode 100644 index 944ffde25..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/ffconf.h +++ /dev/null @@ -1,272 +0,0 @@ -/* CHIBIOS FIX */ -#include "ch.h" - -/*---------------------------------------------------------------------------/ -/ FatFs - Configuration file -/---------------------------------------------------------------------------*/ - -#define FFCONF_DEF 87030 /* Revision ID */ - -/*---------------------------------------------------------------------------/ -/ Function Configurations -/---------------------------------------------------------------------------*/ - -#define FF_FS_READONLY 0 -/* This option switches read-only configuration. (0:Read/Write or 1:Read-only) -/ Read-only configuration removes writing API functions, f_write(), f_sync(), -/ f_unlink(), f_mkdir(), f_chmod(), f_rename(), f_truncate(), f_getfree() -/ and optional writing functions as well. */ - - -#define FF_FS_MINIMIZE 0 -/* This option defines minimization level to remove some basic API functions. -/ -/ 0: All basic functions are enabled. -/ 1: f_stat(), f_getfree(), f_unlink(), f_mkdir(), f_truncate() and f_rename() -/ are removed. -/ 2: f_opendir(), f_readdir() and f_closedir() are removed in addition to 1. -/ 3: f_lseek() function is removed in addition to 2. */ - - -#define FF_USE_STRFUNC 0 -/* This option switches string functions, f_gets(), f_putc(), f_puts() and f_printf(). -/ -/ 0: Disable string functions. -/ 1: Enable without LF-CRLF conversion. -/ 2: Enable with LF-CRLF conversion. */ - - -#define FF_USE_FIND 0 -/* This option switches filtered directory read functions, f_findfirst() and -/ f_findnext(). (0:Disable, 1:Enable 2:Enable with matching altname[] too) */ - - -#define FF_USE_MKFS 0 -/* This option switches f_mkfs() function. (0:Disable or 1:Enable) */ - - -#define FF_USE_FASTSEEK 0 -/* This option switches fast seek function. (0:Disable or 1:Enable) */ - - -#define FF_USE_EXPAND 0 -/* This option switches f_expand function. (0:Disable or 1:Enable) */ - - -#define FF_USE_CHMOD 0 -/* This option switches attribute manipulation functions, f_chmod() and f_utime(). -/ (0:Disable or 1:Enable) Also FF_FS_READONLY needs to be 0 to enable this option. */ - - -#define FF_USE_LABEL 0 -/* This option switches volume label functions, f_getlabel() and f_setlabel(). -/ (0:Disable or 1:Enable) */ - - -#define FF_USE_FORWARD 0 -/* This option switches f_forward() function. (0:Disable or 1:Enable) */ - - -/*---------------------------------------------------------------------------/ -/ Locale and Namespace Configurations -/---------------------------------------------------------------------------*/ - -#define FF_CODE_PAGE 850 -/* This option specifies the OEM code page to be used on the target system. -/ Incorrect code page setting can cause a file open failure. -/ -/ 437 - U.S. -/ 720 - Arabic -/ 737 - Greek -/ 771 - KBL -/ 775 - Baltic -/ 850 - Latin 1 -/ 852 - Latin 2 -/ 855 - Cyrillic -/ 857 - Turkish -/ 860 - Portuguese -/ 861 - Icelandic -/ 862 - Hebrew -/ 863 - Canadian French -/ 864 - Arabic -/ 865 - Nordic -/ 866 - Russian -/ 869 - Greek 2 -/ 932 - Japanese (DBCS) -/ 936 - Simplified Chinese (DBCS) -/ 949 - Korean (DBCS) -/ 950 - Traditional Chinese (DBCS) -/ 0 - Include all code pages above and configured by f_setcp() -*/ - - -#define FF_USE_LFN 3 -#define FF_MAX_LFN 255 -/* The FF_USE_LFN switches the support for LFN (long file name). -/ -/ 0: Disable LFN. FF_MAX_LFN has no effect. -/ 1: Enable LFN with static working buffer on the BSS. Always NOT thread-safe. -/ 2: Enable LFN with dynamic working buffer on the STACK. -/ 3: Enable LFN with dynamic working buffer on the HEAP. -/ -/ To enable the LFN, Unicode handling functions (option/unicode.c) must be added -/ to the project. The working buffer occupies (FF_MAX_LFN + 1) * 2 bytes and -/ additional 608 bytes at exFAT enabled. FF_MAX_LFN can be in range from 12 to 255. -/ It should be set 255 to support full featured LFN operations. -/ When use stack for the working buffer, take care on stack overflow. When use heap -/ memory for the working buffer, memory management functions, ff_memalloc() and -/ ff_memfree(), must be added to the project. */ - - -#define FF_LFN_UNICODE 0 -/* This option switches character encoding on the API, 0:ANSI/OEM or 1:UTF-16, -/ when LFN is enabled. Also behavior of string I/O functions will be affected by -/ this option. When LFN is not enabled, this option has no effect. -*/ - - -#define FF_STRF_ENCODE 3 -/* When FF_LFN_UNICODE = 1 with LFN enabled, string I/O functions, f_gets(), -/ f_putc(), f_puts and f_printf() convert the character encoding in it. -/ This option selects assumption of character encoding ON THE FILE to be -/ read/written via those functions. -/ -/ 0: ANSI/OEM -/ 1: UTF-16LE -/ 2: UTF-16BE -/ 3: UTF-8 -*/ - - -#define FF_FS_RPATH 0 -/* This option configures support for relative path. -/ -/ 0: Disable relative path and remove related functions. -/ 1: Enable relative path. f_chdir() and f_chdrive() are available. -/ 2: f_getcwd() function is available in addition to 1. -*/ - - -/*---------------------------------------------------------------------------/ -/ Drive/Volume Configurations -/---------------------------------------------------------------------------*/ - -#define FF_VOLUMES 1 -/* Number of volumes (logical drives) to be used. (1-10) */ - - -#define FF_STR_VOLUME_ID 0 -#define FF_VOLUME_STRS "RAM","NAND","CF","SD","SD2","USB","USB2","USB3" -/* FF_STR_VOLUME_ID switches string support for volume ID. -/ When FF_STR_VOLUME_ID is set to 1, also pre-defined strings can be used as drive -/ number in the path name. FF_VOLUME_STRS defines the drive ID strings for each -/ logical drives. Number of items must be equal to FF_VOLUMES. Valid characters for -/ the drive ID strings are: A-Z and 0-9. */ - - -#define FF_MULTI_PARTITION 0 -/* This option switches support for multiple volumes on the physical drive. -/ By default (0), each logical drive number is bound to the same physical drive -/ number and only an FAT volume found on the physical drive will be mounted. -/ When this function is enabled (1), each logical drive number can be bound to -/ arbitrary physical drive and partition listed in the VolToPart[]. Also f_fdisk() -/ funciton will be available. */ - - -#define FF_MIN_SS 512 -#define FF_MAX_SS 512 -/* This set of options configures the range of sector size to be supported. (512, -/ 1024, 2048 or 4096) Always set both 512 for most systems, generic memory card and -/ harddisk. But a larger value may be required for on-board flash memory and some -/ type of optical media. When FF_MAX_SS is larger than FF_MIN_SS, FatFs is configured -/ for variable sector size mode and disk_ioctl() function needs to implement -/ GET_SECTOR_SIZE command. */ - - -#define FF_USE_TRIM 0 -/* This option switches support for ATA-TRIM. (0:Disable or 1:Enable) -/ To enable Trim function, also CTRL_TRIM command should be implemented to the -/ disk_ioctl() function. */ - - -#define FF_FS_NOFSINFO 0 -/* If you need to know correct free space on the FAT32 volume, set bit 0 of this -/ option, and f_getfree() function at first time after volume mount will force -/ a full FAT scan. Bit 1 controls the use of last allocated cluster number. -/ -/ bit0=0: Use free cluster count in the FSINFO if available. -/ bit0=1: Do not trust free cluster count in the FSINFO. -/ bit1=0: Use last allocated cluster number in the FSINFO if available. -/ bit1=1: Do not trust last allocated cluster number in the FSINFO. -*/ - - - -/*---------------------------------------------------------------------------/ -/ System Configurations -/---------------------------------------------------------------------------*/ - -#define FF_FS_TINY 0 -/* This option switches tiny buffer configuration. (0:Normal or 1:Tiny) -/ At the tiny configuration, size of file object (FIL) is shrinked FF_MAX_SS bytes. -/ Instead of private sector buffer eliminated from the file object, common sector -/ buffer in the filesystem object (FATFS) is used for the file data transfer. */ - - -#define FF_FS_EXFAT 1 -/* This option switches support for exFAT filesystem. (0:Disable or 1:Enable) -/ When enable exFAT, also LFN needs to be enabled. -/ Note that enabling exFAT discards ANSI C (C89) compatibility. */ - - -#define FF_FS_NORTC 1 -#define FF_NORTC_MON 5 -#define FF_NORTC_MDAY 1 -#define FF_NORTC_YEAR 2017 -/* The option FF_FS_NORTC switches timestamp functiton. If the system does not have -/ any RTC function or valid timestamp is not needed, set FF_FS_NORTC = 1 to disable -/ the timestamp function. All objects modified by FatFs will have a fixed timestamp -/ defined by FF_NORTC_MON, FF_NORTC_MDAY and FF_NORTC_YEAR in local time. -/ To enable timestamp function (FF_FS_NORTC = 0), get_fattime() function need to be -/ added to the project to read current time form real-time clock. FF_NORTC_MON, -/ FF_NORTC_MDAY and FF_NORTC_YEAR have no effect. -/ These options have no effect at read-only configuration (FF_FS_READONLY = 1). */ - - -#define FF_FS_LOCK 0 -/* The option FF_FS_LOCK switches file lock function to control duplicated file open -/ and illegal operation to open objects. This option must be 0 when FF_FS_READONLY -/ is 1. -/ -/ 0: Disable file lock function. To avoid volume corruption, application program -/ should avoid illegal open, remove and rename to the open objects. -/ >0: Enable file lock function. The value defines how many files/sub-directories -/ can be opened simultaneously under file lock control. Note that the file -/ lock control is independent of re-entrancy. */ - - -#define FF_FS_REENTRANT 0 -#define FF_FS_TIMEOUT MS2ST(1000) -#define FF_SYNC_t semaphore_t* -/* The option FF_FS_REENTRANT switches the re-entrancy (thread safe) of the FatFs -/ module itself. Note that regardless of this option, file access to different -/ volume is always re-entrant and volume control functions, f_mount(), f_mkfs() -/ and f_fdisk() function, are always not re-entrant. Only file/directory access -/ to the same volume is under control of this function. -/ -/ 0: Disable re-entrancy. FF_FS_TIMEOUT and FF_SYNC_t have no effect. -/ 1: Enable re-entrancy. Also user provided synchronization handlers, -/ ff_req_grant(), ff_rel_grant(), ff_del_syncobj() and ff_cre_syncobj() -/ function, must be added to the project. Samples are available in -/ option/syscall.c. -/ -/ The FF_FS_TIMEOUT defines timeout period in unit of time tick. -/ The FF_SYNC_t defines O/S dependent sync object type. e.g. HANDLE, ID, OS_EVENT*, -/ SemaphoreHandle_t and etc. A header file for O/S definitions needs to be -/ included somewhere in the scope of ff.h. */ - -/* #include // O/S definitions */ - - - -/*--- End of configuration options ---*/ diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/halconf.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/halconf.h deleted file mode 100644 index cdf73d129..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/halconf.h +++ /dev/null @@ -1,395 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -/** - * @file templates/halconf.h - * @brief HAL configuration header. - * @details HAL configuration file, this file allows to enable or disable the - * various device drivers from your application. You may also use - * this file in order to override the device drivers default settings. - * - * @addtogroup HAL_CONF - * @{ - */ - -#ifndef HALCONF_H -#define HALCONF_H - -#include "mcuconf.h" - -/** - * @brief Enables the TM subsystem. - */ -#if !defined(HAL_USE_TM) || defined(__DOXYGEN__) -#define HAL_USE_TM TRUE -#endif - -/** - * @brief Enables the PAL subsystem. - */ -#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) -#define HAL_USE_PAL TRUE -#endif - -/** - * @brief Enables the ADC subsystem. - */ -#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) -#define HAL_USE_ADC FALSE -#endif - -/** - * @brief Enables the CAN subsystem. - */ -#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) -#define HAL_USE_CAN FALSE -#endif - -/** - * @brief Enables the DAC subsystem. - */ -#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) -#define HAL_USE_DAC FALSE -#endif - -/** - * @brief Enables the EXT subsystem. - */ -#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) -#define HAL_USE_EXT FALSE -#endif - -/** - * @brief Enables the GPT subsystem. - */ -#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) -#define HAL_USE_GPT FALSE -#endif - -/** - * @brief Enables the I2C subsystem. - */ -#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) -#define HAL_USE_I2C FALSE -#endif - -/** - * @brief Enables the I2S subsystem. - */ -#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) -#define HAL_USE_I2S FALSE -#endif - -/** - * @brief Enables the ICU subsystem. - */ -#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) -#define HAL_USE_ICU FALSE -#endif - -/** - * @brief Enables the MAC subsystem. - */ -#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) -#define HAL_USE_MAC TRUE -#endif - -/** - * @brief Enables the MMC_SPI subsystem. - */ -#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) -#define HAL_USE_MMC_SPI FALSE -#endif - -/** - * @brief Enables the PWM subsystem. - */ -#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) -#define HAL_USE_PWM FALSE -#endif - -/** - * @brief Enables the QSPI subsystem. - */ -#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__) -#define HAL_USE_QSPI FALSE -#endif - -/** - * @brief Enables the RTC subsystem. - */ -#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) -#define HAL_USE_RTC FALSE -#endif - -/** - * @brief Enables the SDC subsystem. - */ -#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) -#define HAL_USE_SDC TRUE -#endif - -/** - * @brief Enables the SERIAL subsystem. - */ -#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) -#define HAL_USE_SERIAL TRUE -#endif - -/** - * @brief Enables the SERIAL over USB subsystem. - */ -#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) -#define HAL_USE_SERIAL_USB TRUE -#endif - -/** - * @brief Enables the SPI subsystem. - */ -#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) -#define HAL_USE_SPI FALSE -#endif - -/** - * @brief Enables the UART subsystem. - */ -#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) -#define HAL_USE_UART FALSE -#endif - -/** - * @brief Enables the USB subsystem. - */ -#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) -#define HAL_USE_USB TRUE -#endif - -/** - * @brief Enables the WDG subsystem. - */ -#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) -#define HAL_USE_WDG FALSE -#endif - -/*===========================================================================*/ -/* ADC driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Enables synchronous APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) -#define ADC_USE_WAIT TRUE -#endif - -/** - * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) -#define ADC_USE_MUTUAL_EXCLUSION TRUE -#endif - -/*===========================================================================*/ -/* CAN driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Sleep mode related APIs inclusion switch. - */ -#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) -#define CAN_USE_SLEEP_MODE TRUE -#endif - -/*===========================================================================*/ -/* I2C driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Enables the mutual exclusion APIs on the I2C bus. - */ -#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) -#define I2C_USE_MUTUAL_EXCLUSION TRUE -#endif - -/*===========================================================================*/ -/* MAC driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Enables an event sources for incoming packets. - */ -#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) -#define MAC_USE_ZERO_COPY FALSE -#endif - -/** - * @brief Enables an event sources for incoming packets. - */ -#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) -#define MAC_USE_EVENTS TRUE -#endif - -/*===========================================================================*/ -/* MMC_SPI driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Delays insertions. - * @details If enabled this options inserts delays into the MMC waiting - * routines releasing some extra CPU time for the threads with - * lower priority, this may slow down the driver a bit however. - * This option is recommended also if the SPI driver does not - * use a DMA channel and heavily loads the CPU. - */ -#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) -#define MMC_NICE_WAITING TRUE -#endif - -/*===========================================================================*/ -/* SDC driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Number of initialization attempts before rejecting the card. - * @note Attempts are performed at 10mS intervals. - */ -#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) -#define SDC_INIT_RETRY 100 -#endif - -/** - * @brief Include support for MMC cards. - * @note MMC support is not yet implemented so this option must be kept - * at @p FALSE. - */ -#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) -#define SDC_MMC_SUPPORT FALSE -#endif - -/** - * @brief Delays insertions. - * @details If enabled this options inserts delays into the MMC waiting - * routines releasing some extra CPU time for the threads with - * lower priority, this may slow down the driver a bit however. - */ -#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) -#define SDC_NICE_WAITING TRUE -#endif - -/*===========================================================================*/ -/* SERIAL driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Default bit rate. - * @details Configuration parameter, this is the baud rate selected for the - * default configuration. - */ -#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) -#define SERIAL_DEFAULT_BITRATE 38400 -#endif - -/** - * @brief Serial buffers size. - * @details Configuration parameter, you can change the depth of the queue - * buffers depending on the requirements of your application. - * @note The default is 16 bytes for both the transmission and receive - * buffers. - */ -#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) -#define SERIAL_BUFFERS_SIZE 16 -#endif - -/*===========================================================================*/ -/* SERIAL_USB driver related setting. */ -/*===========================================================================*/ - -/** - * @brief Serial over USB buffers size. - * @details Configuration parameter, the buffer size must be a multiple of - * the USB data endpoint maximum packet size. - * @note The default is 256 bytes for both the transmission and receive - * buffers. - */ -#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) -#define SERIAL_USB_BUFFERS_SIZE 256 -#endif - -/** - * @brief Serial over USB number of buffers. - * @note The default is 2 buffers. - */ -#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__) -#define SERIAL_USB_BUFFERS_NUMBER 2 -#endif - -/*===========================================================================*/ -/* SPI driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Enables synchronous APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) -#define SPI_USE_WAIT TRUE -#endif - -/** - * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) -#define SPI_USE_MUTUAL_EXCLUSION TRUE -#endif - -/*===========================================================================*/ -/* UART driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Enables synchronous APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__) -#define UART_USE_WAIT FALSE -#endif - -/** - * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) -#define UART_USE_MUTUAL_EXCLUSION FALSE -#endif - -/*===========================================================================*/ -/* USB driver related settings. */ -/*===========================================================================*/ - -/** - * @brief Enables synchronous APIs. - * @note Disabling this option saves both code and data space. - */ -#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) -#define USB_USE_WAIT FALSE -#endif - -#endif /* HALCONF_H */ - -/** @} */ diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/httpd_opts.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/httpd_opts.h deleted file mode 100644 index 2669745f5..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/httpd_opts.h +++ /dev/null @@ -1,323 +0,0 @@ -/** - * @file - * HTTP server options list - */ - -/* - * Copyright (c) 2001-2003 Swedish Institute of Computer Science. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. The name of the author may not be used to endorse or promote products - * derived from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT - * SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, - * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT - * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING - * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY - * OF SUCH DAMAGE. - * - * This file is part of the lwIP TCP/IP stack. - * - * Author: Adam Dunkels - * - * This version of the file has been modified by Texas Instruments to offer - * simple server-side-include (SSI) and Common Gateway Interface (CGI) - * capability. - */ - -#ifndef LWIP_HDR_APPS_HTTPD_OPTS_H -#define LWIP_HDR_APPS_HTTPD_OPTS_H - -#include "lwip/opt.h" - -/** - * @defgroup httpd_opts Options - * @ingroup httpd - * @{ - */ - -/** Set this to 1 to support CGI (old style) */ -#if !defined LWIP_HTTPD_CGI || defined __DOXYGEN__ -#define LWIP_HTTPD_CGI 0 -#endif - -/** Set this to 1 to support CGI (new style) */ -#if !defined LWIP_HTTPD_CGI_SSI || defined __DOXYGEN__ -#define LWIP_HTTPD_CGI_SSI 0 -#endif - -/** Set this to 1 to support SSI (Server-Side-Includes) */ -#if !defined LWIP_HTTPD_SSI || defined __DOXYGEN__ -#define LWIP_HTTPD_SSI 0 -#endif - -/** Set this to 1 to implement an SSI tag handler callback that gets a const char* - * to the tag (instead of an index into a pre-registered array of known tags) */ -#if !defined LWIP_HTTPD_SSI_RAW || defined __DOXYGEN__ -#define LWIP_HTTPD_SSI_RAW 0 -#endif - -/** Set this to 1 to support HTTP POST */ -#if !defined LWIP_HTTPD_SUPPORT_POST || defined __DOXYGEN__ -#define LWIP_HTTPD_SUPPORT_POST 0 -#endif - -/* The maximum number of parameters that the CGI handler can be sent. */ -#if !defined LWIP_HTTPD_MAX_CGI_PARAMETERS || defined __DOXYGEN__ -#define LWIP_HTTPD_MAX_CGI_PARAMETERS 16 -#endif - -/** LWIP_HTTPD_SSI_MULTIPART==1: SSI handler function is called with 2 more - * arguments indicating a counter for insert string that are too long to be - * inserted at once: the SSI handler function must then set 'next_tag_part' - * which will be passed back to it in the next call. */ -#if !defined LWIP_HTTPD_SSI_MULTIPART || defined __DOXYGEN__ -#define LWIP_HTTPD_SSI_MULTIPART 0 -#endif - -/* The maximum length of the string comprising the tag name */ -#if !defined LWIP_HTTPD_MAX_TAG_NAME_LEN || defined __DOXYGEN__ -#define LWIP_HTTPD_MAX_TAG_NAME_LEN 8 -#endif - -/* The maximum length of string that can be returned to replace any given tag */ -#if !defined LWIP_HTTPD_MAX_TAG_INSERT_LEN || defined __DOXYGEN__ -#define LWIP_HTTPD_MAX_TAG_INSERT_LEN 192 -#endif - -#if !defined LWIP_HTTPD_POST_MANUAL_WND || defined __DOXYGEN__ -#define LWIP_HTTPD_POST_MANUAL_WND 0 -#endif - -/** This string is passed in the HTTP header as "Server: " */ -#if !defined HTTPD_SERVER_AGENT || defined __DOXYGEN__ -#define HTTPD_SERVER_AGENT "lwIP/" LWIP_VERSION_STRING " (http://savannah.nongnu.org/projects/lwip)" -#endif - -/** Set this to 1 if you want to include code that creates HTTP headers - * at runtime. Default is off: HTTP headers are then created statically - * by the makefsdata tool. Static headers mean smaller code size, but - * the (readonly) fsdata will grow a bit as every file includes the HTTP - * header. */ -#if !defined LWIP_HTTPD_DYNAMIC_HEADERS || defined __DOXYGEN__ -#define LWIP_HTTPD_DYNAMIC_HEADERS 0 -#endif - -#if !defined HTTPD_DEBUG || defined __DOXYGEN__ -#define HTTPD_DEBUG LWIP_DBG_OFF -#endif - -/** Set this to 1 to use a memp pool for allocating - * struct http_state instead of the heap. - */ -#if !defined HTTPD_USE_MEM_POOL || defined __DOXYGEN__ -#define HTTPD_USE_MEM_POOL 0 -#endif - -/** The server port for HTTPD to use */ -#if !defined HTTPD_SERVER_PORT || defined __DOXYGEN__ -#define HTTPD_SERVER_PORT 80 -#endif - -/** Maximum retries before the connection is aborted/closed. - * - number of times pcb->poll is called -> default is 4*500ms = 2s; - * - reset when pcb->sent is called - */ -#if !defined HTTPD_MAX_RETRIES || defined __DOXYGEN__ -#define HTTPD_MAX_RETRIES 4 -#endif - -/** The poll delay is X*500ms */ -#if !defined HTTPD_POLL_INTERVAL || defined __DOXYGEN__ -#define HTTPD_POLL_INTERVAL 4 -#endif - -/** Priority for tcp pcbs created by HTTPD (very low by default). - * Lower priorities get killed first when running out of memory. - */ -#if !defined HTTPD_TCP_PRIO || defined __DOXYGEN__ -#define HTTPD_TCP_PRIO TCP_PRIO_MIN -#endif - -/** Set this to 1 to enable timing each file sent */ -#if !defined LWIP_HTTPD_TIMING || defined __DOXYGEN__ -#define LWIP_HTTPD_TIMING 0 -#endif -/** Set this to 1 to enable timing each file sent */ -#if !defined HTTPD_DEBUG_TIMING || defined __DOXYGEN__ -#define HTTPD_DEBUG_TIMING LWIP_DBG_OFF -#endif - -/** Set this to one to show error pages when parsing a request fails instead - of simply closing the connection. */ -#if !defined LWIP_HTTPD_SUPPORT_EXTSTATUS || defined __DOXYGEN__ -#define LWIP_HTTPD_SUPPORT_EXTSTATUS 0 -#endif - -/** Set this to 0 to drop support for HTTP/0.9 clients (to save some bytes) */ -#if !defined LWIP_HTTPD_SUPPORT_V09 || defined __DOXYGEN__ -#define LWIP_HTTPD_SUPPORT_V09 1 -#endif - -/** Set this to 1 to enable HTTP/1.1 persistent connections. - * ATTENTION: If the generated file system includes HTTP headers, these must - * include the "Connection: keep-alive" header (pass argument "-11" to makefsdata). - */ -#if !defined LWIP_HTTPD_SUPPORT_11_KEEPALIVE || defined __DOXYGEN__ -#define LWIP_HTTPD_SUPPORT_11_KEEPALIVE 0 -#endif - -/** Set this to 1 to support HTTP request coming in in multiple packets/pbufs */ -#if !defined LWIP_HTTPD_SUPPORT_REQUESTLIST || defined __DOXYGEN__ -#define LWIP_HTTPD_SUPPORT_REQUESTLIST 1 -#endif - -#if LWIP_HTTPD_SUPPORT_REQUESTLIST -/** Number of rx pbufs to enqueue to parse an incoming request (up to the first - newline) */ -#if !defined LWIP_HTTPD_REQ_QUEUELEN || defined __DOXYGEN__ -#define LWIP_HTTPD_REQ_QUEUELEN 5 -#endif - -/** Number of (TCP payload-) bytes (in pbufs) to enqueue to parse and incoming - request (up to the first double-newline) */ -#if !defined LWIP_HTTPD_REQ_BUFSIZE || defined __DOXYGEN__ -#define LWIP_HTTPD_REQ_BUFSIZE LWIP_HTTPD_MAX_REQ_LENGTH -#endif - -/** Defines the maximum length of a HTTP request line (up to the first CRLF, - copied from pbuf into this a global buffer when pbuf- or packet-queues - are received - otherwise the input pbuf is used directly) */ -#if !defined LWIP_HTTPD_MAX_REQ_LENGTH || defined __DOXYGEN__ -#define LWIP_HTTPD_MAX_REQ_LENGTH LWIP_MIN(1023, (LWIP_HTTPD_REQ_QUEUELEN * PBUF_POOL_BUFSIZE)) -#endif -#endif /* LWIP_HTTPD_SUPPORT_REQUESTLIST */ - -/** This is the size of a static buffer used when URIs end with '/'. - * In this buffer, the directory requested is concatenated with all the - * configured default file names. - * Set to 0 to disable checking default filenames on non-root directories. - */ -#if !defined LWIP_HTTPD_MAX_REQUEST_URI_LEN || defined __DOXYGEN__ -#define LWIP_HTTPD_MAX_REQUEST_URI_LEN 63 -#endif - -/** Maximum length of the filename to send as response to a POST request, - * filled in by the application when a POST is finished. - */ -#if !defined LWIP_HTTPD_POST_MAX_RESPONSE_URI_LEN || defined __DOXYGEN__ -#define LWIP_HTTPD_POST_MAX_RESPONSE_URI_LEN 63 -#endif - -/** Set this to 0 to not send the SSI tag (default is on, so the tag will - * be sent in the HTML page */ -#if !defined LWIP_HTTPD_SSI_INCLUDE_TAG || defined __DOXYGEN__ -#define LWIP_HTTPD_SSI_INCLUDE_TAG 1 -#endif - -/** Set this to 1 to call tcp_abort when tcp_close fails with memory error. - * This can be used to prevent consuming all memory in situations where the - * HTTP server has low priority compared to other communication. */ -#if !defined LWIP_HTTPD_ABORT_ON_CLOSE_MEM_ERROR || defined __DOXYGEN__ -#define LWIP_HTTPD_ABORT_ON_CLOSE_MEM_ERROR 0 -#endif - -/** Set this to 1 to kill the oldest connection when running out of - * memory for 'struct http_state' or 'struct http_ssi_state'. - * ATTENTION: This puts all connections on a linked list, so may be kind of slow. - */ -#if !defined LWIP_HTTPD_KILL_OLD_ON_CONNECTIONS_EXCEEDED || defined __DOXYGEN__ -#define LWIP_HTTPD_KILL_OLD_ON_CONNECTIONS_EXCEEDED 0 -#endif - -/** Set this to 1 to send URIs without extension without headers - * (who uses this at all??) */ -#if !defined LWIP_HTTPD_OMIT_HEADER_FOR_EXTENSIONLESS_URI || defined __DOXYGEN__ -#define LWIP_HTTPD_OMIT_HEADER_FOR_EXTENSIONLESS_URI 0 -#endif - -/** Default: Tags are sent from struct http_state and are therefore volatile */ -#if !defined HTTP_IS_TAG_VOLATILE || defined __DOXYGEN__ -#define HTTP_IS_TAG_VOLATILE(ptr) TCP_WRITE_FLAG_COPY -#endif - -/* By default, the httpd is limited to send 2*pcb->mss to keep resource usage low - when http is not an important protocol in the device. */ -#if !defined HTTPD_LIMIT_SENDING_TO_2MSS || defined __DOXYGEN__ -#define HTTPD_LIMIT_SENDING_TO_2MSS 1 -#endif - -/* Define this to a function that returns the maximum amount of data to enqueue. - The function have this signature: u16_t fn(struct tcp_pcb* pcb); */ -#if !defined HTTPD_MAX_WRITE_LEN || defined __DOXYGEN__ -#if HTTPD_LIMIT_SENDING_TO_2MSS -#define HTTPD_MAX_WRITE_LEN(pcb) (2 * tcp_mss(pcb)) -#endif -#endif - -/*------------------- FS OPTIONS -------------------*/ - -/** Set this to 1 and provide the functions: - * - "int fs_open_custom(struct fs_file *file, const char *name)" - * Called first for every opened file to allow opening files - * that are not included in fsdata(_custom).c - * - "void fs_close_custom(struct fs_file *file)" - * Called to free resources allocated by fs_open_custom(). - */ -#if !defined LWIP_HTTPD_CUSTOM_FILES || defined __DOXYGEN__ -#define LWIP_HTTPD_CUSTOM_FILES 0 -#endif - -/** Set this to 1 to support fs_read() to dynamically read file data. - * Without this (default=off), only one-block files are supported, - * and the contents must be ready after fs_open(). - */ -#if !defined LWIP_HTTPD_DYNAMIC_FILE_READ || defined __DOXYGEN__ -#define LWIP_HTTPD_DYNAMIC_FILE_READ 0 -#endif - -/** Set this to 1 to include an application state argument per file - * that is opened. This allows to keep a state per connection/file. - */ -#if !defined LWIP_HTTPD_FILE_STATE || defined __DOXYGEN__ -#define LWIP_HTTPD_FILE_STATE 0 -#endif - -/** HTTPD_PRECALCULATED_CHECKSUM==1: include precompiled checksums for - * predefined (MSS-sized) chunks of the files to prevent having to calculate - * the checksums at runtime. */ -#if !defined HTTPD_PRECALCULATED_CHECKSUM || defined __DOXYGEN__ -#define HTTPD_PRECALCULATED_CHECKSUM 0 -#endif - -/** LWIP_HTTPD_FS_ASYNC_READ==1: support asynchronous read operations - * (fs_read_async returns FS_READ_DELAYED and calls a callback when finished). - */ -#if !defined LWIP_HTTPD_FS_ASYNC_READ || defined __DOXYGEN__ -#define LWIP_HTTPD_FS_ASYNC_READ 0 -#endif - -/** Set this to 1 to include "fsdata_custom.c" instead of "fsdata.c" for the - * file system (to prevent changing the file included in CVS) */ -#if !defined HTTPD_USE_CUSTOM_FSDATA || defined __DOXYGEN__ -#define HTTPD_USE_CUSTOM_FSDATA 0 -#endif - -/** - * @} - */ - -#endif /* LWIP_HDR_APPS_HTTPD_OPTS_H */ diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/lwipopts.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/lwipopts.h deleted file mode 100644 index 5a8e51970..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/lwipopts.h +++ /dev/null @@ -1,2127 +0,0 @@ -/** - * @file - * - * lwIP Options Configuration - */ - -/* - * Copyright (c) 2001-2004 Swedish Institute of Computer Science. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. The name of the author may not be used to endorse or promote products - * derived from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT - * SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, - * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT - * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS - * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN - * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING - * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY - * OF SUCH DAMAGE. - * - * This file is part of the lwIP TCP/IP stack. - * - * Author: Adam Dunkels - * - */ -#ifndef __LWIPOPT_H__ -#define __LWIPOPT_H__ - - -/* - ----------------------------------------------- - ---------- Platform specific locking ---------- - ----------------------------------------------- -*/ - -/** - * SYS_LIGHTWEIGHT_PROT==1: if you want inter-task protection for certain - * critical regions during buffer allocation, deallocation and memory - * allocation and deallocation. - */ -#ifndef SYS_LIGHTWEIGHT_PROT -#define SYS_LIGHTWEIGHT_PROT 0 -#endif - -/** - * NO_SYS==1: Provides VERY minimal functionality. Otherwise, - * use lwIP facilities. - */ -#ifndef NO_SYS -#define NO_SYS 0 -#endif - -/** - * NO_SYS_NO_TIMERS==1: Drop support for sys_timeout when NO_SYS==1 - * Mainly for compatibility to old versions. - */ -#ifndef NO_SYS_NO_TIMERS -#define NO_SYS_NO_TIMERS 0 -#endif - -/** - * MEMCPY: override this if you have a faster implementation at hand than the - * one included in your C library - */ -#ifndef MEMCPY -#define MEMCPY(dst,src,len) memcpy(dst,src,len) -#endif - -/** - * SMEMCPY: override this with care! Some compilers (e.g. gcc) can inline a - * call to memcpy() if the length is known at compile time and is small. - */ -#ifndef SMEMCPY -#define SMEMCPY(dst,src,len) memcpy(dst,src,len) -#endif - -/* - ------------------------------------ - ---------- Memory options ---------- - ------------------------------------ -*/ -/** - * MEM_LIBC_MALLOC==1: Use malloc/free/realloc provided by your C-library - * instead of the lwip internal allocator. Can save code size if you - * already use it. - */ -#ifndef MEM_LIBC_MALLOC -#define MEM_LIBC_MALLOC 0 -#endif - -/** -* MEMP_MEM_MALLOC==1: Use mem_malloc/mem_free instead of the lwip pool allocator. -* Especially useful with MEM_LIBC_MALLOC but handle with care regarding execution -* speed and usage from interrupts! -*/ -#ifndef MEMP_MEM_MALLOC -#define MEMP_MEM_MALLOC 0 -#endif - -/** - * MEM_ALIGNMENT: should be set to the alignment of the CPU - * 4 byte alignment -> #define MEM_ALIGNMENT 4 - * 2 byte alignment -> #define MEM_ALIGNMENT 2 - */ -#ifndef MEM_ALIGNMENT -#define MEM_ALIGNMENT 4 -#endif - -/** - * MEM_SIZE: the size of the heap memory. If the application will send - * a lot of data that needs to be copied, this should be set high. - */ -#ifndef MEM_SIZE -#define MEM_SIZE 1600 -#endif - -/** - * MEMP_SEPARATE_POOLS: if defined to 1, each pool is placed in its own array. - * This can be used to individually change the location of each pool. - * Default is one big array for all pools - */ -#ifndef MEMP_SEPARATE_POOLS -#define MEMP_SEPARATE_POOLS 0 -#endif - -/** - * MEMP_OVERFLOW_CHECK: memp overflow protection reserves a configurable - * amount of bytes before and after each memp element in every pool and fills - * it with a prominent default value. - * MEMP_OVERFLOW_CHECK == 0 no checking - * MEMP_OVERFLOW_CHECK == 1 checks each element when it is freed - * MEMP_OVERFLOW_CHECK >= 2 checks each element in every pool every time - * memp_malloc() or memp_free() is called (useful but slow!) - */ -#ifndef MEMP_OVERFLOW_CHECK -#define MEMP_OVERFLOW_CHECK 0 -#endif - -/** - * MEMP_SANITY_CHECK==1: run a sanity check after each memp_free() to make - * sure that there are no cycles in the linked lists. - */ -#ifndef MEMP_SANITY_CHECK -#define MEMP_SANITY_CHECK 0 -#endif - -/** - * MEM_USE_POOLS==1: Use an alternative to malloc() by allocating from a set - * of memory pools of various sizes. When mem_malloc is called, an element of - * the smallest pool that can provide the length needed is returned. - * To use this, MEMP_USE_CUSTOM_POOLS also has to be enabled. - */ -#ifndef MEM_USE_POOLS -#define MEM_USE_POOLS 0 -#endif - -/** - * MEM_USE_POOLS_TRY_BIGGER_POOL==1: if one malloc-pool is empty, try the next - * bigger pool - WARNING: THIS MIGHT WASTE MEMORY but it can make a system more - * reliable. */ -#ifndef MEM_USE_POOLS_TRY_BIGGER_POOL -#define MEM_USE_POOLS_TRY_BIGGER_POOL 0 -#endif - -/** - * MEMP_USE_CUSTOM_POOLS==1: whether to include a user file lwippools.h - * that defines additional pools beyond the "standard" ones required - * by lwIP. If you set this to 1, you must have lwippools.h in your - * inlude path somewhere. - */ -#ifndef MEMP_USE_CUSTOM_POOLS -#define MEMP_USE_CUSTOM_POOLS 0 -#endif - -/** - * Set this to 1 if you want to free PBUF_RAM pbufs (or call mem_free()) from - * interrupt context (or another context that doesn't allow waiting for a - * semaphore). - * If set to 1, mem_malloc will be protected by a semaphore and SYS_ARCH_PROTECT, - * while mem_free will only use SYS_ARCH_PROTECT. mem_malloc SYS_ARCH_UNPROTECTs - * with each loop so that mem_free can run. - * - * ATTENTION: As you can see from the above description, this leads to dis-/ - * enabling interrupts often, which can be slow! Also, on low memory, mem_malloc - * can need longer. - * - * If you don't want that, at least for NO_SYS=0, you can still use the following - * functions to enqueue a deallocation call which then runs in the tcpip_thread - * context: - * - pbuf_free_callback(p); - * - mem_free_callback(m); - */ -#ifndef LWIP_ALLOW_MEM_FREE_FROM_OTHER_CONTEXT -#define LWIP_ALLOW_MEM_FREE_FROM_OTHER_CONTEXT 0 -#endif - -/* - ------------------------------------------------ - ---------- Internal Memory Pool Sizes ---------- - ------------------------------------------------ -*/ -/** - * MEMP_NUM_PBUF: the number of memp struct pbufs (used for PBUF_ROM and PBUF_REF). - * If the application sends a lot of data out of ROM (or other static memory), - * this should be set high. - */ -#ifndef MEMP_NUM_PBUF -#define MEMP_NUM_PBUF 16 -#endif - -/** - * MEMP_NUM_RAW_PCB: Number of raw connection PCBs - * (requires the LWIP_RAW option) - */ -#ifndef MEMP_NUM_RAW_PCB -#define MEMP_NUM_RAW_PCB 4 -#endif - -/** - * MEMP_NUM_UDP_PCB: the number of UDP protocol control blocks. One - * per active UDP "connection". - * (requires the LWIP_UDP option) - */ -#ifndef MEMP_NUM_UDP_PCB -#define MEMP_NUM_UDP_PCB 4 -#endif - -/** - * MEMP_NUM_TCP_PCB: the number of simulatenously active TCP connections. - * (requires the LWIP_TCP option) - */ -#ifndef MEMP_NUM_TCP_PCB -#define MEMP_NUM_TCP_PCB 5 -#endif - -/** - * MEMP_NUM_TCP_PCB_LISTEN: the number of listening TCP connections. - * (requires the LWIP_TCP option) - */ -#ifndef MEMP_NUM_TCP_PCB_LISTEN -#define MEMP_NUM_TCP_PCB_LISTEN 8 -#endif - -/** - * MEMP_NUM_TCP_SEG: the number of simultaneously queued TCP segments. - * (requires the LWIP_TCP option) - */ -#ifndef MEMP_NUM_TCP_SEG -#define MEMP_NUM_TCP_SEG 16 -#endif - -/** - * MEMP_NUM_REASSDATA: the number of IP packets simultaneously queued for - * reassembly (whole packets, not fragments!) - */ -#ifndef MEMP_NUM_REASSDATA -#define MEMP_NUM_REASSDATA 5 -#endif - -/** - * MEMP_NUM_FRAG_PBUF: the number of IP fragments simultaneously sent - * (fragments, not whole packets!). - * This is only used with IP_FRAG_USES_STATIC_BUF==0 and - * LWIP_NETIF_TX_SINGLE_PBUF==0 and only has to be > 1 with DMA-enabled MACs - * where the packet is not yet sent when netif->output returns. - */ -#ifndef MEMP_NUM_FRAG_PBUF -#define MEMP_NUM_FRAG_PBUF 15 -#endif - -/** - * MEMP_NUM_ARP_QUEUE: the number of simulateously queued outgoing - * packets (pbufs) that are waiting for an ARP request (to resolve - * their destination address) to finish. - * (requires the ARP_QUEUEING option) - */ -#ifndef MEMP_NUM_ARP_QUEUE -#define MEMP_NUM_ARP_QUEUE 30 -#endif - -/** - * MEMP_NUM_IGMP_GROUP: The number of multicast groups whose network interfaces - * can be members et the same time (one per netif - allsystems group -, plus one - * per netif membership). - * (requires the LWIP_IGMP option) - */ -#ifndef MEMP_NUM_IGMP_GROUP -#define MEMP_NUM_IGMP_GROUP 8 -#endif - -/** - * MEMP_NUM_SYS_TIMEOUT: the number of simulateously active timeouts. - * (requires NO_SYS==0) - * The default number of timeouts is calculated here for all enabled modules. - * The formula expects settings to be either '0' or '1'. - */ -#ifndef MEMP_NUM_SYS_TIMEOUT -#define MEMP_NUM_SYS_TIMEOUT (LWIP_TCP + IP_REASSEMBLY + LWIP_ARP + (2*LWIP_DHCP) + LWIP_AUTOIP + LWIP_IGMP + LWIP_DNS + PPP_SUPPORT) -#endif - -/** - * MEMP_NUM_NETBUF: the number of struct netbufs. - * (only needed if you use the sequential API, like api_lib.c) - */ -#ifndef MEMP_NUM_NETBUF -#define MEMP_NUM_NETBUF 2 -#endif - -/** - * MEMP_NUM_NETCONN: the number of struct netconns. - * (only needed if you use the sequential API, like api_lib.c) - */ -#ifndef MEMP_NUM_NETCONN -#define MEMP_NUM_NETCONN 4 -#endif - -/** - * MEMP_NUM_TCPIP_MSG_API: the number of struct tcpip_msg, which are used - * for callback/timeout API communication. - * (only needed if you use tcpip.c) - */ -#ifndef MEMP_NUM_TCPIP_MSG_API -#define MEMP_NUM_TCPIP_MSG_API 8 -#endif - -/** - * MEMP_NUM_TCPIP_MSG_INPKT: the number of struct tcpip_msg, which are used - * for incoming packets. - * (only needed if you use tcpip.c) - */ -#ifndef MEMP_NUM_TCPIP_MSG_INPKT -#define MEMP_NUM_TCPIP_MSG_INPKT 8 -#endif - -/** - * MEMP_NUM_SNMP_NODE: the number of leafs in the SNMP tree. - */ -#ifndef MEMP_NUM_SNMP_NODE -#define MEMP_NUM_SNMP_NODE 50 -#endif - -/** - * MEMP_NUM_SNMP_ROOTNODE: the number of branches in the SNMP tree. - * Every branch has one leaf (MEMP_NUM_SNMP_NODE) at least! - */ -#ifndef MEMP_NUM_SNMP_ROOTNODE -#define MEMP_NUM_SNMP_ROOTNODE 30 -#endif - -/** - * MEMP_NUM_SNMP_VARBIND: the number of concurrent requests (does not have to - * be changed normally) - 2 of these are used per request (1 for input, - * 1 for output) - */ -#ifndef MEMP_NUM_SNMP_VARBIND -#define MEMP_NUM_SNMP_VARBIND 2 -#endif - -/** - * MEMP_NUM_SNMP_VALUE: the number of OID or values concurrently used - * (does not have to be changed normally) - 3 of these are used per request - * (1 for the value read and 2 for OIDs - input and output) - */ -#ifndef MEMP_NUM_SNMP_VALUE -#define MEMP_NUM_SNMP_VALUE 3 -#endif - -/** - * MEMP_NUM_NETDB: the number of concurrently running lwip_addrinfo() calls - * (before freeing the corresponding memory using lwip_freeaddrinfo()). - */ -#ifndef MEMP_NUM_NETDB -#define MEMP_NUM_NETDB 1 -#endif - -/** - * MEMP_NUM_LOCALHOSTLIST: the number of host entries in the local host list - * if DNS_LOCAL_HOSTLIST_IS_DYNAMIC==1. - */ -#ifndef MEMP_NUM_LOCALHOSTLIST -#define MEMP_NUM_LOCALHOSTLIST 1 -#endif - -/** - * MEMP_NUM_PPPOE_INTERFACES: the number of concurrently active PPPoE - * interfaces (only used with PPPOE_SUPPORT==1) - */ -#ifndef MEMP_NUM_PPPOE_INTERFACES -#define MEMP_NUM_PPPOE_INTERFACES 1 -#endif - -/** - * PBUF_POOL_SIZE: the number of buffers in the pbuf pool. - */ -#ifndef PBUF_POOL_SIZE -#define PBUF_POOL_SIZE 16 -#endif - -/* - --------------------------------- - ---------- ARP options ---------- - --------------------------------- -*/ -/** - * LWIP_ARP==1: Enable ARP functionality. - */ -#ifndef LWIP_ARP -#define LWIP_ARP 1 -#endif - -/** - * ARP_TABLE_SIZE: Number of active MAC-IP address pairs cached. - */ -#ifndef ARP_TABLE_SIZE -#define ARP_TABLE_SIZE 10 -#endif - -/** - * ARP_QUEUEING==1: Multiple outgoing packets are queued during hardware address - * resolution. By default, only the most recent packet is queued per IP address. - * This is sufficient for most protocols and mainly reduces TCP connection - * startup time. Set this to 1 if you know your application sends more than one - * packet in a row to an IP address that is not in the ARP cache. - */ -#ifndef ARP_QUEUEING -#define ARP_QUEUEING 0 -#endif - -/** - * ETHARP_TRUST_IP_MAC==1: Incoming IP packets cause the ARP table to be - * updated with the source MAC and IP addresses supplied in the packet. - * You may want to disable this if you do not trust LAN peers to have the - * correct addresses, or as a limited approach to attempt to handle - * spoofing. If disabled, lwIP will need to make a new ARP request if - * the peer is not already in the ARP table, adding a little latency. - * The peer *is* in the ARP table if it requested our address before. - * Also notice that this slows down input processing of every IP packet! - */ -#ifndef ETHARP_TRUST_IP_MAC -#define ETHARP_TRUST_IP_MAC 0 -#endif - -/** - * ETHARP_SUPPORT_VLAN==1: support receiving ethernet packets with VLAN header. - * Additionally, you can define ETHARP_VLAN_CHECK to an u16_t VLAN ID to check. - * If ETHARP_VLAN_CHECK is defined, only VLAN-traffic for this VLAN is accepted. - * If ETHARP_VLAN_CHECK is not defined, all traffic is accepted. - * Alternatively, define a function/define ETHARP_VLAN_CHECK_FN(eth_hdr, vlan) - * that returns 1 to accept a packet or 0 to drop a packet. - */ -#ifndef ETHARP_SUPPORT_VLAN -#define ETHARP_SUPPORT_VLAN 0 -#endif - -/** LWIP_ETHERNET==1: enable ethernet support for PPPoE even though ARP - * might be disabled - */ -#ifndef LWIP_ETHERNET -#define LWIP_ETHERNET (LWIP_ARP || PPPOE_SUPPORT) -#endif - -/** ETH_PAD_SIZE: number of bytes added before the ethernet header to ensure - * alignment of payload after that header. Since the header is 14 bytes long, - * without this padding e.g. addresses in the IP header will not be aligned - * on a 32-bit boundary, so setting this to 2 can speed up 32-bit-platforms. - */ -#ifndef ETH_PAD_SIZE -#define ETH_PAD_SIZE 0 -#endif - -/** ETHARP_SUPPORT_STATIC_ENTRIES==1: enable code to support static ARP table - * entries (using etharp_add_static_entry/etharp_remove_static_entry). - */ -#ifndef ETHARP_SUPPORT_STATIC_ENTRIES -#define ETHARP_SUPPORT_STATIC_ENTRIES 0 -#endif - - -/* - -------------------------------- - ---------- IP options ---------- - -------------------------------- -*/ -/** - * IP_FORWARD==1: Enables the ability to forward IP packets across network - * interfaces. If you are going to run lwIP on a device with only one network - * interface, define this to 0. - */ -#ifndef IP_FORWARD -#define IP_FORWARD 0 -#endif - -/** - * IP_OPTIONS_ALLOWED: Defines the behavior for IP options. - * IP_OPTIONS_ALLOWED==0: All packets with IP options are dropped. - * IP_OPTIONS_ALLOWED==1: IP options are allowed (but not parsed). - */ -#ifndef IP_OPTIONS_ALLOWED -#define IP_OPTIONS_ALLOWED 1 -#endif - -/** - * IP_REASSEMBLY==1: Reassemble incoming fragmented IP packets. Note that - * this option does not affect outgoing packet sizes, which can be controlled - * via IP_FRAG. - */ -#ifndef IP_REASSEMBLY -#define IP_REASSEMBLY 1 -#endif - -/** - * IP_FRAG==1: Fragment outgoing IP packets if their size exceeds MTU. Note - * that this option does not affect incoming packet sizes, which can be - * controlled via IP_REASSEMBLY. - */ -#ifndef IP_FRAG -#define IP_FRAG 1 -#endif - -/** - * IP_REASS_MAXAGE: Maximum time (in multiples of IP_TMR_INTERVAL - so seconds, normally) - * a fragmented IP packet waits for all fragments to arrive. If not all fragments arrived - * in this time, the whole packet is discarded. - */ -#ifndef IP_REASS_MAXAGE -#define IP_REASS_MAXAGE 3 -#endif - -/** - * IP_REASS_MAX_PBUFS: Total maximum amount of pbufs waiting to be reassembled. - * Since the received pbufs are enqueued, be sure to configure - * PBUF_POOL_SIZE > IP_REASS_MAX_PBUFS so that the stack is still able to receive - * packets even if the maximum amount of fragments is enqueued for reassembly! - */ -#ifndef IP_REASS_MAX_PBUFS -#define IP_REASS_MAX_PBUFS 10 -#endif - -/** - * IP_FRAG_USES_STATIC_BUF==1: Use a static MTU-sized buffer for IP - * fragmentation. Otherwise pbufs are allocated and reference the original - * packet data to be fragmented (or with LWIP_NETIF_TX_SINGLE_PBUF==1, - * new PBUF_RAM pbufs are used for fragments). - * ATTENTION: IP_FRAG_USES_STATIC_BUF==1 may not be used for DMA-enabled MACs! - */ -#ifndef IP_FRAG_USES_STATIC_BUF -#define IP_FRAG_USES_STATIC_BUF 0 -#endif - -/** - * IP_FRAG_MAX_MTU: Assumed max MTU on any interface for IP frag buffer - * (requires IP_FRAG_USES_STATIC_BUF==1) - */ -#if IP_FRAG_USES_STATIC_BUF && !defined(IP_FRAG_MAX_MTU) -#define IP_FRAG_MAX_MTU 1500 -#endif - -/** - * IP_DEFAULT_TTL: Default value for Time-To-Live used by transport layers. - */ -#ifndef IP_DEFAULT_TTL -#define IP_DEFAULT_TTL 255 -#endif - -/** - * IP_SOF_BROADCAST=1: Use the SOF_BROADCAST field to enable broadcast - * filter per pcb on udp and raw send operations. To enable broadcast filter - * on recv operations, you also have to set IP_SOF_BROADCAST_RECV=1. - */ -#ifndef IP_SOF_BROADCAST -#define IP_SOF_BROADCAST 0 -#endif - -/** - * IP_SOF_BROADCAST_RECV (requires IP_SOF_BROADCAST=1) enable the broadcast - * filter on recv operations. - */ -#ifndef IP_SOF_BROADCAST_RECV -#define IP_SOF_BROADCAST_RECV 0 -#endif - -/** - * IP_FORWARD_ALLOW_TX_ON_RX_NETIF==1: allow ip_forward() to send packets back - * out on the netif where it was received. This should only be used for - * wireless networks. - * ATTENTION: When this is 1, make sure your netif driver correctly marks incoming - * link-layer-broadcast/multicast packets as such using the corresponding pbuf flags! - */ -#ifndef IP_FORWARD_ALLOW_TX_ON_RX_NETIF -#define IP_FORWARD_ALLOW_TX_ON_RX_NETIF 0 -#endif - -/** - * LWIP_RANDOMIZE_INITIAL_LOCAL_PORTS==1: randomize the local port for the first - * local TCP/UDP pcb (default==0). This can prevent creating predictable port - * numbers after booting a device. - */ -#ifndef LWIP_RANDOMIZE_INITIAL_LOCAL_PORTS -#define LWIP_RANDOMIZE_INITIAL_LOCAL_PORTS 0 -#endif - -/* - ---------------------------------- - ---------- ICMP options ---------- - ---------------------------------- -*/ -/** - * LWIP_ICMP==1: Enable ICMP module inside the IP stack. - * Be careful, disable that make your product non-compliant to RFC1122 - */ -#ifndef LWIP_ICMP -#define LWIP_ICMP 1 -#endif - -/** - * ICMP_TTL: Default value for Time-To-Live used by ICMP packets. - */ -#ifndef ICMP_TTL -#define ICMP_TTL (IP_DEFAULT_TTL) -#endif - -/** - * LWIP_BROADCAST_PING==1: respond to broadcast pings (default is unicast only) - */ -#ifndef LWIP_BROADCAST_PING -#define LWIP_BROADCAST_PING 0 -#endif - -/** - * LWIP_MULTICAST_PING==1: respond to multicast pings (default is unicast only) - */ -#ifndef LWIP_MULTICAST_PING -#define LWIP_MULTICAST_PING 0 -#endif - -/* - --------------------------------- - ---------- RAW options ---------- - --------------------------------- -*/ -/** - * LWIP_RAW==1: Enable application layer to hook into the IP layer itself. - */ -#ifndef LWIP_RAW -#define LWIP_RAW 1 -#endif - -/** - * LWIP_RAW==1: Enable application layer to hook into the IP layer itself. - */ -#ifndef RAW_TTL -#define RAW_TTL (IP_DEFAULT_TTL) -#endif - -/* - ---------------------------------- - ---------- DHCP options ---------- - ---------------------------------- -*/ -/** - * LWIP_DHCP==1: Enable DHCP module. - */ -#ifndef LWIP_DHCP -#define LWIP_DHCP 0 -#endif - -/** - * DHCP_DOES_ARP_CHECK==1: Do an ARP check on the offered address. - */ -#ifndef DHCP_DOES_ARP_CHECK -#define DHCP_DOES_ARP_CHECK ((LWIP_DHCP) && (LWIP_ARP)) -#endif - -/* - ------------------------------------ - ---------- AUTOIP options ---------- - ------------------------------------ -*/ -/** - * LWIP_AUTOIP==1: Enable AUTOIP module. - */ -#ifndef LWIP_AUTOIP -#define LWIP_AUTOIP 0 -#endif - -/** - * LWIP_DHCP_AUTOIP_COOP==1: Allow DHCP and AUTOIP to be both enabled on - * the same interface at the same time. - */ -#ifndef LWIP_DHCP_AUTOIP_COOP -#define LWIP_DHCP_AUTOIP_COOP 0 -#endif - -/** - * LWIP_DHCP_AUTOIP_COOP_TRIES: Set to the number of DHCP DISCOVER probes - * that should be sent before falling back on AUTOIP. This can be set - * as low as 1 to get an AutoIP address very quickly, but you should - * be prepared to handle a changing IP address when DHCP overrides - * AutoIP. - */ -#ifndef LWIP_DHCP_AUTOIP_COOP_TRIES -#define LWIP_DHCP_AUTOIP_COOP_TRIES 9 -#endif - -/* - ---------------------------------- - ---------- SNMP options ---------- - ---------------------------------- -*/ -/** - * LWIP_SNMP==1: Turn on SNMP module. UDP must be available for SNMP - * transport. - */ -#ifndef LWIP_SNMP -#define LWIP_SNMP 0 -#endif - -/** - * SNMP_CONCURRENT_REQUESTS: Number of concurrent requests the module will - * allow. At least one request buffer is required. - * Does not have to be changed unless external MIBs answer request asynchronously - */ -#ifndef SNMP_CONCURRENT_REQUESTS -#define SNMP_CONCURRENT_REQUESTS 1 -#endif - -/** - * SNMP_TRAP_DESTINATIONS: Number of trap destinations. At least one trap - * destination is required - */ -#ifndef SNMP_TRAP_DESTINATIONS -#define SNMP_TRAP_DESTINATIONS 1 -#endif - -/** - * SNMP_PRIVATE_MIB: - * When using a private MIB, you have to create a file 'private_mib.h' that contains - * a 'struct mib_array_node mib_private' which contains your MIB. - */ -#ifndef SNMP_PRIVATE_MIB -#define SNMP_PRIVATE_MIB 0 -#endif - -/** - * Only allow SNMP write actions that are 'safe' (e.g. disabeling netifs is not - * a safe action and disabled when SNMP_SAFE_REQUESTS = 1). - * Unsafe requests are disabled by default! - */ -#ifndef SNMP_SAFE_REQUESTS -#define SNMP_SAFE_REQUESTS 1 -#endif - -/** - * The maximum length of strings used. This affects the size of - * MEMP_SNMP_VALUE elements. - */ -#ifndef SNMP_MAX_OCTET_STRING_LEN -#define SNMP_MAX_OCTET_STRING_LEN 127 -#endif - -/** - * The maximum depth of the SNMP tree. - * With private MIBs enabled, this depends on your MIB! - * This affects the size of MEMP_SNMP_VALUE elements. - */ -#ifndef SNMP_MAX_TREE_DEPTH -#define SNMP_MAX_TREE_DEPTH 15 -#endif - -/** - * The size of the MEMP_SNMP_VALUE elements, normally calculated from - * SNMP_MAX_OCTET_STRING_LEN and SNMP_MAX_TREE_DEPTH. - */ -#ifndef SNMP_MAX_VALUE_SIZE -#define SNMP_MAX_VALUE_SIZE LWIP_MAX((SNMP_MAX_OCTET_STRING_LEN)+1, sizeof(s32_t)*(SNMP_MAX_TREE_DEPTH)) -#endif - -/* - ---------------------------------- - ---------- IGMP options ---------- - ---------------------------------- -*/ -/** - * LWIP_IGMP==1: Turn on IGMP module. - */ -#ifndef LWIP_IGMP -#define LWIP_IGMP 0 -#endif - -/* - ---------------------------------- - ---------- DNS options ----------- - ---------------------------------- -*/ -/** - * LWIP_DNS==1: Turn on DNS module. UDP must be available for DNS - * transport. - */ -#ifndef LWIP_DNS -#define LWIP_DNS 0 -#endif - -/** DNS maximum number of entries to maintain locally. */ -#ifndef DNS_TABLE_SIZE -#define DNS_TABLE_SIZE 4 -#endif - -/** DNS maximum host name length supported in the name table. */ -#ifndef DNS_MAX_NAME_LENGTH -#define DNS_MAX_NAME_LENGTH 256 -#endif - -/** The maximum of DNS servers */ -#ifndef DNS_MAX_SERVERS -#define DNS_MAX_SERVERS 2 -#endif - -/** DNS do a name checking between the query and the response. */ -#ifndef DNS_DOES_NAME_CHECK -#define DNS_DOES_NAME_CHECK 1 -#endif - -/** DNS message max. size. Default value is RFC compliant. */ -#ifndef DNS_MSG_SIZE -#define DNS_MSG_SIZE 512 -#endif - -/** DNS_LOCAL_HOSTLIST: Implements a local host-to-address list. If enabled, - * you have to define - * #define DNS_LOCAL_HOSTLIST_INIT {{"host1", 0x123}, {"host2", 0x234}} - * (an array of structs name/address, where address is an u32_t in network - * byte order). - * - * Instead, you can also use an external function: - * #define DNS_LOOKUP_LOCAL_EXTERN(x) extern u32_t my_lookup_function(const char *name) - * that returns the IP address or INADDR_NONE if not found. - */ -#ifndef DNS_LOCAL_HOSTLIST -#define DNS_LOCAL_HOSTLIST 0 -#endif /* DNS_LOCAL_HOSTLIST */ - -/** If this is turned on, the local host-list can be dynamically changed - * at runtime. */ -#ifndef DNS_LOCAL_HOSTLIST_IS_DYNAMIC -#define DNS_LOCAL_HOSTLIST_IS_DYNAMIC 0 -#endif /* DNS_LOCAL_HOSTLIST_IS_DYNAMIC */ - -/* - --------------------------------- - ---------- UDP options ---------- - --------------------------------- -*/ -/** - * LWIP_UDP==1: Turn on UDP. - */ -#ifndef LWIP_UDP -#define LWIP_UDP 1 -#endif - -/** - * LWIP_UDPLITE==1: Turn on UDP-Lite. (Requires LWIP_UDP) - */ -#ifndef LWIP_UDPLITE -#define LWIP_UDPLITE 0 -#endif - -/** - * UDP_TTL: Default Time-To-Live value. - */ -#ifndef UDP_TTL -#define UDP_TTL (IP_DEFAULT_TTL) -#endif - -/** - * LWIP_NETBUF_RECVINFO==1: append destination addr and port to every netbuf. - */ -#ifndef LWIP_NETBUF_RECVINFO -#define LWIP_NETBUF_RECVINFO 0 -#endif - -/* - --------------------------------- - ---------- TCP options ---------- - --------------------------------- -*/ -/** - * LWIP_TCP==1: Turn on TCP. - */ -#ifndef LWIP_TCP -#define LWIP_TCP 1 -#endif - -/** - * TCP_TTL: Default Time-To-Live value. - */ -#ifndef TCP_TTL -#define TCP_TTL (IP_DEFAULT_TTL) -#endif - -/** - * TCP_WND: The size of a TCP window. This must be at least - * (2 * TCP_MSS) for things to work well - */ -#ifndef TCP_WND -#define TCP_WND (4 * TCP_MSS) -#endif - -/** - * TCP_MAXRTX: Maximum number of retransmissions of data segments. - */ -#ifndef TCP_MAXRTX -#define TCP_MAXRTX 12 -#endif - -/** - * TCP_SYNMAXRTX: Maximum number of retransmissions of SYN segments. - */ -#ifndef TCP_SYNMAXRTX -#define TCP_SYNMAXRTX 6 -#endif - -/** - * TCP_QUEUE_OOSEQ==1: TCP will queue segments that arrive out of order. - * Define to 0 if your device is low on memory. - */ -#ifndef TCP_QUEUE_OOSEQ -#define TCP_QUEUE_OOSEQ (LWIP_TCP) -#endif - -/** - * TCP_MSS: TCP Maximum segment size. (default is 536, a conservative default, - * you might want to increase this.) - * For the receive side, this MSS is advertised to the remote side - * when opening a connection. For the transmit size, this MSS sets - * an upper limit on the MSS advertised by the remote host. - */ -#ifndef TCP_MSS -#define TCP_MSS 536 -#endif - -/** - * TCP_CALCULATE_EFF_SEND_MSS: "The maximum size of a segment that TCP really - * sends, the 'effective send MSS,' MUST be the smaller of the send MSS (which - * reflects the available reassembly buffer size at the remote host) and the - * largest size permitted by the IP layer" (RFC 1122) - * Setting this to 1 enables code that checks TCP_MSS against the MTU of the - * netif used for a connection and limits the MSS if it would be too big otherwise. - */ -#ifndef TCP_CALCULATE_EFF_SEND_MSS -#define TCP_CALCULATE_EFF_SEND_MSS 1 -#endif - - -/** - * TCP_SND_BUF: TCP sender buffer space (bytes). - * To achieve good performance, this should be at least 2 * TCP_MSS. - */ -#ifndef TCP_SND_BUF -#define TCP_SND_BUF (2 * TCP_MSS) -#endif - -/** - * TCP_SND_QUEUELEN: TCP sender buffer space (pbufs). This must be at least - * as much as (2 * TCP_SND_BUF/TCP_MSS) for things to work. - */ -#ifndef TCP_SND_QUEUELEN -#define TCP_SND_QUEUELEN ((4 * (TCP_SND_BUF) + (TCP_MSS - 1))/(TCP_MSS)) -#endif - -/** - * TCP_SNDLOWAT: TCP writable space (bytes). This must be less than - * TCP_SND_BUF. It is the amount of space which must be available in the - * TCP snd_buf for select to return writable (combined with TCP_SNDQUEUELOWAT). - */ -#ifndef TCP_SNDLOWAT -#define TCP_SNDLOWAT LWIP_MIN(LWIP_MAX(((TCP_SND_BUF)/2), (2 * TCP_MSS) + 1), (TCP_SND_BUF) - 1) -#endif - -/** - * TCP_SNDQUEUELOWAT: TCP writable bufs (pbuf count). This must be less - * than TCP_SND_QUEUELEN. If the number of pbufs queued on a pcb drops below - * this number, select returns writable (combined with TCP_SNDLOWAT). - */ -#ifndef TCP_SNDQUEUELOWAT -#define TCP_SNDQUEUELOWAT LWIP_MAX(((TCP_SND_QUEUELEN)/2), 5) -#endif - -/** - * TCP_OOSEQ_MAX_BYTES: The maximum number of bytes queued on ooseq per pcb. - * Default is 0 (no limit). Only valid for TCP_QUEUE_OOSEQ==0. - */ -#ifndef TCP_OOSEQ_MAX_BYTES -#define TCP_OOSEQ_MAX_BYTES 0 -#endif - -/** - * TCP_OOSEQ_MAX_PBUFS: The maximum number of pbufs queued on ooseq per pcb. - * Default is 0 (no limit). Only valid for TCP_QUEUE_OOSEQ==0. - */ -#ifndef TCP_OOSEQ_MAX_PBUFS -#define TCP_OOSEQ_MAX_PBUFS 0 -#endif - -/** - * TCP_LISTEN_BACKLOG: Enable the backlog option for tcp listen pcb. - */ -#ifndef TCP_LISTEN_BACKLOG -#define TCP_LISTEN_BACKLOG 0 -#endif - -/** - * The maximum allowed backlog for TCP listen netconns. - * This backlog is used unless another is explicitly specified. - * 0xff is the maximum (u8_t). - */ -#ifndef TCP_DEFAULT_LISTEN_BACKLOG -#define TCP_DEFAULT_LISTEN_BACKLOG 0xff -#endif - -/** - * TCP_OVERSIZE: The maximum number of bytes that tcp_write may - * allocate ahead of time in an attempt to create shorter pbuf chains - * for transmission. The meaningful range is 0 to TCP_MSS. Some - * suggested values are: - * - * 0: Disable oversized allocation. Each tcp_write() allocates a new - pbuf (old behaviour). - * 1: Allocate size-aligned pbufs with minimal excess. Use this if your - * scatter-gather DMA requires aligned fragments. - * 128: Limit the pbuf/memory overhead to 20%. - * TCP_MSS: Try to create unfragmented TCP packets. - * TCP_MSS/4: Try to create 4 fragments or less per TCP packet. - */ -#ifndef TCP_OVERSIZE -#define TCP_OVERSIZE TCP_MSS -#endif - -/** - * LWIP_TCP_TIMESTAMPS==1: support the TCP timestamp option. - */ -#ifndef LWIP_TCP_TIMESTAMPS -#define LWIP_TCP_TIMESTAMPS 0 -#endif - -/** - * TCP_WND_UPDATE_THRESHOLD: difference in window to trigger an - * explicit window update - */ -#ifndef TCP_WND_UPDATE_THRESHOLD -#define TCP_WND_UPDATE_THRESHOLD (TCP_WND / 4) -#endif - -/** - * LWIP_EVENT_API and LWIP_CALLBACK_API: Only one of these should be set to 1. - * LWIP_EVENT_API==1: The user defines lwip_tcp_event() to receive all - * events (accept, sent, etc) that happen in the system. - * LWIP_CALLBACK_API==1: The PCB callback function is called directly - * for the event. This is the default. - */ -#if !defined(LWIP_EVENT_API) && !defined(LWIP_CALLBACK_API) -#define LWIP_EVENT_API 0 -#define LWIP_CALLBACK_API 1 -#endif - - -/* - ---------------------------------- - ---------- Pbuf options ---------- - ---------------------------------- -*/ -/** - * PBUF_LINK_HLEN: the number of bytes that should be allocated for a - * link level header. The default is 14, the standard value for - * Ethernet. - */ -#ifndef PBUF_LINK_HLEN -#define PBUF_LINK_HLEN (14 + ETH_PAD_SIZE) -#endif - -/** - * PBUF_POOL_BUFSIZE: the size of each pbuf in the pbuf pool. The default is - * designed to accomodate single full size TCP frame in one pbuf, including - * TCP_MSS, IP header, and link header. - */ -#ifndef PBUF_POOL_BUFSIZE -#define PBUF_POOL_BUFSIZE LWIP_MEM_ALIGN_SIZE(TCP_MSS+40+PBUF_LINK_HLEN) -#endif - -/* - ------------------------------------------------ - ---------- Network Interfaces options ---------- - ------------------------------------------------ -*/ -/** - * LWIP_NETIF_HOSTNAME==1: use DHCP_OPTION_HOSTNAME with netif's hostname - * field. - */ -#ifndef LWIP_NETIF_HOSTNAME -#define LWIP_NETIF_HOSTNAME 0 -#endif - -/** - * LWIP_NETIF_API==1: Support netif api (in netifapi.c) - */ -#ifndef LWIP_NETIF_API -#define LWIP_NETIF_API 0 -#endif - -/** - * LWIP_NETIF_STATUS_CALLBACK==1: Support a callback function whenever an interface - * changes its up/down status (i.e., due to DHCP IP acquistion) - */ -#ifndef LWIP_NETIF_STATUS_CALLBACK -#define LWIP_NETIF_STATUS_CALLBACK 0 -#endif - -/** - * LWIP_NETIF_LINK_CALLBACK==1: Support a callback function from an interface - * whenever the link changes (i.e., link down) - */ -#ifndef LWIP_NETIF_LINK_CALLBACK -#define LWIP_NETIF_LINK_CALLBACK 0 -#endif - -/** - * LWIP_NETIF_REMOVE_CALLBACK==1: Support a callback function that is called - * when a netif has been removed - */ -#ifndef LWIP_NETIF_REMOVE_CALLBACK -#define LWIP_NETIF_REMOVE_CALLBACK 0 -#endif - -/** - * LWIP_NETIF_HWADDRHINT==1: Cache link-layer-address hints (e.g. table - * indices) in struct netif. TCP and UDP can make use of this to prevent - * scanning the ARP table for every sent packet. While this is faster for big - * ARP tables or many concurrent connections, it might be counterproductive - * if you have a tiny ARP table or if there never are concurrent connections. - */ -#ifndef LWIP_NETIF_HWADDRHINT -#define LWIP_NETIF_HWADDRHINT 0 -#endif - -/** - * LWIP_NETIF_LOOPBACK==1: Support sending packets with a destination IP - * address equal to the netif IP address, looping them back up the stack. - */ -#ifndef LWIP_NETIF_LOOPBACK -#define LWIP_NETIF_LOOPBACK 0 -#endif - -/** - * LWIP_LOOPBACK_MAX_PBUFS: Maximum number of pbufs on queue for loopback - * sending for each netif (0 = disabled) - */ -#ifndef LWIP_LOOPBACK_MAX_PBUFS -#define LWIP_LOOPBACK_MAX_PBUFS 0 -#endif - -/** - * LWIP_NETIF_LOOPBACK_MULTITHREADING: Indicates whether threading is enabled in - * the system, as netifs must change how they behave depending on this setting - * for the LWIP_NETIF_LOOPBACK option to work. - * Setting this is needed to avoid reentering non-reentrant functions like - * tcp_input(). - * LWIP_NETIF_LOOPBACK_MULTITHREADING==1: Indicates that the user is using a - * multithreaded environment like tcpip.c. In this case, netif->input() - * is called directly. - * LWIP_NETIF_LOOPBACK_MULTITHREADING==0: Indicates a polling (or NO_SYS) setup. - * The packets are put on a list and netif_poll() must be called in - * the main application loop. - */ -#ifndef LWIP_NETIF_LOOPBACK_MULTITHREADING -#define LWIP_NETIF_LOOPBACK_MULTITHREADING (!NO_SYS) -#endif - -/** - * LWIP_NETIF_TX_SINGLE_PBUF: if this is set to 1, lwIP tries to put all data - * to be sent into one single pbuf. This is for compatibility with DMA-enabled - * MACs that do not support scatter-gather. - * Beware that this might involve CPU-memcpy before transmitting that would not - * be needed without this flag! Use this only if you need to! - * - * @todo: TCP and IP-frag do not work with this, yet: - */ -#ifndef LWIP_NETIF_TX_SINGLE_PBUF -#define LWIP_NETIF_TX_SINGLE_PBUF 0 -#endif /* LWIP_NETIF_TX_SINGLE_PBUF */ - -/* - ------------------------------------ - ---------- LOOPIF options ---------- - ------------------------------------ -*/ -/** - * LWIP_HAVE_LOOPIF==1: Support loop interface (127.0.0.1) and loopif.c - */ -#ifndef LWIP_HAVE_LOOPIF -#define LWIP_HAVE_LOOPIF 0 -#endif - -/* - ------------------------------------ - ---------- SLIPIF options ---------- - ------------------------------------ -*/ -/** - * LWIP_HAVE_SLIPIF==1: Support slip interface and slipif.c - */ -#ifndef LWIP_HAVE_SLIPIF -#define LWIP_HAVE_SLIPIF 0 -#endif - -/* - ------------------------------------ - ---------- Thread options ---------- - ------------------------------------ -*/ -/** - * TCPIP_THREAD_NAME: The name assigned to the main tcpip thread. - */ -#ifndef TCPIP_THREAD_NAME -#define TCPIP_THREAD_NAME "tcpip_thread" -#endif - -/** - * TCPIP_THREAD_STACKSIZE: The stack size used by the main tcpip thread. - * The stack size value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef TCPIP_THREAD_STACKSIZE -#define TCPIP_THREAD_STACKSIZE 1024 -#endif - -/** - * TCPIP_THREAD_PRIO: The priority assigned to the main tcpip thread. - * The priority value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef TCPIP_THREAD_PRIO -#define TCPIP_THREAD_PRIO (LOWPRIO + 1) -#endif - -/** - * TCPIP_MBOX_SIZE: The mailbox size for the tcpip thread messages - * The queue size value itself is platform-dependent, but is passed to - * sys_mbox_new() when tcpip_init is called. - */ -#ifndef TCPIP_MBOX_SIZE -#define TCPIP_MBOX_SIZE MEMP_NUM_PBUF -#endif - -/** - * SLIPIF_THREAD_NAME: The name assigned to the slipif_loop thread. - */ -#ifndef SLIPIF_THREAD_NAME -#define SLIPIF_THREAD_NAME "slipif_loop" -#endif - -/** - * SLIP_THREAD_STACKSIZE: The stack size used by the slipif_loop thread. - * The stack size value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef SLIPIF_THREAD_STACKSIZE -#define SLIPIF_THREAD_STACKSIZE 1024 -#endif - -/** - * SLIPIF_THREAD_PRIO: The priority assigned to the slipif_loop thread. - * The priority value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef SLIPIF_THREAD_PRIO -#define SLIPIF_THREAD_PRIO (LOWPRIO + 1) -#endif - -/** - * PPP_THREAD_NAME: The name assigned to the pppInputThread. - */ -#ifndef PPP_THREAD_NAME -#define PPP_THREAD_NAME "pppInputThread" -#endif - -/** - * PPP_THREAD_STACKSIZE: The stack size used by the pppInputThread. - * The stack size value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef PPP_THREAD_STACKSIZE -#define PPP_THREAD_STACKSIZE 1024 -#endif - -/** - * PPP_THREAD_PRIO: The priority assigned to the pppInputThread. - * The priority value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef PPP_THREAD_PRIO -#define PPP_THREAD_PRIO (LOWPRIO + 1) -#endif - -/** - * DEFAULT_THREAD_NAME: The name assigned to any other lwIP thread. - */ -#ifndef DEFAULT_THREAD_NAME -#define DEFAULT_THREAD_NAME "lwIP" -#endif - -/** - * DEFAULT_THREAD_STACKSIZE: The stack size used by any other lwIP thread. - * The stack size value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef DEFAULT_THREAD_STACKSIZE -#define DEFAULT_THREAD_STACKSIZE 1024 -#endif - -/** - * DEFAULT_THREAD_PRIO: The priority assigned to any other lwIP thread. - * The priority value itself is platform-dependent, but is passed to - * sys_thread_new() when the thread is created. - */ -#ifndef DEFAULT_THREAD_PRIO -#define DEFAULT_THREAD_PRIO (LOWPRIO + 1) -#endif - -/** - * DEFAULT_RAW_RECVMBOX_SIZE: The mailbox size for the incoming packets on a - * NETCONN_RAW. The queue size value itself is platform-dependent, but is passed - * to sys_mbox_new() when the recvmbox is created. - */ -#ifndef DEFAULT_RAW_RECVMBOX_SIZE -#define DEFAULT_RAW_RECVMBOX_SIZE 4 -#endif - -/** - * DEFAULT_UDP_RECVMBOX_SIZE: The mailbox size for the incoming packets on a - * NETCONN_UDP. The queue size value itself is platform-dependent, but is passed - * to sys_mbox_new() when the recvmbox is created. - */ -#ifndef DEFAULT_UDP_RECVMBOX_SIZE -#define DEFAULT_UDP_RECVMBOX_SIZE 4 -#endif - -/** - * DEFAULT_TCP_RECVMBOX_SIZE: The mailbox size for the incoming packets on a - * NETCONN_TCP. The queue size value itself is platform-dependent, but is passed - * to sys_mbox_new() when the recvmbox is created. - */ -#ifndef DEFAULT_TCP_RECVMBOX_SIZE -#define DEFAULT_TCP_RECVMBOX_SIZE 40 -#endif - -/** - * DEFAULT_ACCEPTMBOX_SIZE: The mailbox size for the incoming connections. - * The queue size value itself is platform-dependent, but is passed to - * sys_mbox_new() when the acceptmbox is created. - */ -#ifndef DEFAULT_ACCEPTMBOX_SIZE -#define DEFAULT_ACCEPTMBOX_SIZE 4 -#endif - -/* - ---------------------------------------------- - ---------- Sequential layer options ---------- - ---------------------------------------------- -*/ -/** - * LWIP_TCPIP_CORE_LOCKING: (EXPERIMENTAL!) - * Don't use it if you're not an active lwIP project member - */ -#ifndef LWIP_TCPIP_CORE_LOCKING -#define LWIP_TCPIP_CORE_LOCKING 0 -#endif - -/** - * LWIP_TCPIP_CORE_LOCKING_INPUT: (EXPERIMENTAL!) - * Don't use it if you're not an active lwIP project member - */ -#ifndef LWIP_TCPIP_CORE_LOCKING_INPUT -#define LWIP_TCPIP_CORE_LOCKING_INPUT 0 -#endif - -/** - * LWIP_NETCONN==1: Enable Netconn API (require to use api_lib.c) - */ -#ifndef LWIP_NETCONN -#define LWIP_NETCONN 1 -#endif - -/** LWIP_TCPIP_TIMEOUT==1: Enable tcpip_timeout/tcpip_untimeout tod create - * timers running in tcpip_thread from another thread. - */ -#ifndef LWIP_TCPIP_TIMEOUT -#define LWIP_TCPIP_TIMEOUT 1 -#endif - -/* - ------------------------------------ - ---------- Socket options ---------- - ------------------------------------ -*/ -/** - * LWIP_SOCKET==1: Enable Socket API (require to use sockets.c) - */ -#ifndef LWIP_SOCKET -#define LWIP_SOCKET 1 -#endif - -/** - * LWIP_COMPAT_SOCKETS==1: Enable BSD-style sockets functions names. - * (only used if you use sockets.c) - */ -#ifndef LWIP_COMPAT_SOCKETS -#define LWIP_COMPAT_SOCKETS 1 -#endif - -/** - * LWIP_POSIX_SOCKETS_IO_NAMES==1: Enable POSIX-style sockets functions names. - * Disable this option if you use a POSIX operating system that uses the same - * names (read, write & close). (only used if you use sockets.c) - */ -#ifndef LWIP_POSIX_SOCKETS_IO_NAMES -#define LWIP_POSIX_SOCKETS_IO_NAMES 1 -#endif - -/** - * LWIP_TCP_KEEPALIVE==1: Enable TCP_KEEPIDLE, TCP_KEEPINTVL and TCP_KEEPCNT - * options processing. Note that TCP_KEEPIDLE and TCP_KEEPINTVL have to be set - * in seconds. (does not require sockets.c, and will affect tcp.c) - */ -#ifndef LWIP_TCP_KEEPALIVE -#define LWIP_TCP_KEEPALIVE 0 -#endif - -/** - * LWIP_SO_SNDTIMEO==1: Enable send timeout for sockets/netconns and - * SO_SNDTIMEO processing. - */ -#ifndef LWIP_SO_SNDTIMEO -#define LWIP_SO_SNDTIMEO 0 -#endif - -/** - * LWIP_SO_RCVTIMEO==1: Enable receive timeout for sockets/netconns and - * SO_RCVTIMEO processing. - */ -#ifndef LWIP_SO_RCVTIMEO -#define LWIP_SO_RCVTIMEO 0 -#endif - -/** - * LWIP_SO_RCVBUF==1: Enable SO_RCVBUF processing. - */ -#ifndef LWIP_SO_RCVBUF -#define LWIP_SO_RCVBUF 0 -#endif - -/** - * If LWIP_SO_RCVBUF is used, this is the default value for recv_bufsize. - */ -#ifndef RECV_BUFSIZE_DEFAULT -#define RECV_BUFSIZE_DEFAULT INT_MAX -#endif - -/** - * SO_REUSE==1: Enable SO_REUSEADDR option. - */ -#ifndef SO_REUSE -#define SO_REUSE 0 -#endif - -/** - * SO_REUSE_RXTOALL==1: Pass a copy of incoming broadcast/multicast packets - * to all local matches if SO_REUSEADDR is turned on. - * WARNING: Adds a memcpy for every packet if passing to more than one pcb! - */ -#ifndef SO_REUSE_RXTOALL -#define SO_REUSE_RXTOALL 0 -#endif - -/* - ---------------------------------------- - ---------- Statistics options ---------- - ---------------------------------------- -*/ -/** - * LWIP_STATS==1: Enable statistics collection in lwip_stats. - */ -#ifndef LWIP_STATS -#define LWIP_STATS 1 -#endif - -#if LWIP_STATS - -/** - * LWIP_STATS_DISPLAY==1: Compile in the statistics output functions. - */ -#ifndef LWIP_STATS_DISPLAY -#define LWIP_STATS_DISPLAY 0 -#endif - -/** - * LINK_STATS==1: Enable link stats. - */ -#ifndef LINK_STATS -#define LINK_STATS 1 -#endif - -/** - * ETHARP_STATS==1: Enable etharp stats. - */ -#ifndef ETHARP_STATS -#define ETHARP_STATS (LWIP_ARP) -#endif - -/** - * IP_STATS==1: Enable IP stats. - */ -#ifndef IP_STATS -#define IP_STATS 1 -#endif - -/** - * IPFRAG_STATS==1: Enable IP fragmentation stats. Default is - * on if using either frag or reass. - */ -#ifndef IPFRAG_STATS -#define IPFRAG_STATS (IP_REASSEMBLY || IP_FRAG) -#endif - -/** - * ICMP_STATS==1: Enable ICMP stats. - */ -#ifndef ICMP_STATS -#define ICMP_STATS 1 -#endif - -/** - * IGMP_STATS==1: Enable IGMP stats. - */ -#ifndef IGMP_STATS -#define IGMP_STATS (LWIP_IGMP) -#endif - -/** - * UDP_STATS==1: Enable UDP stats. Default is on if - * UDP enabled, otherwise off. - */ -#ifndef UDP_STATS -#define UDP_STATS (LWIP_UDP) -#endif - -/** - * TCP_STATS==1: Enable TCP stats. Default is on if TCP - * enabled, otherwise off. - */ -#ifndef TCP_STATS -#define TCP_STATS (LWIP_TCP) -#endif - -/** - * MEM_STATS==1: Enable mem.c stats. - */ -#ifndef MEM_STATS -#define MEM_STATS ((MEM_LIBC_MALLOC == 0) && (MEM_USE_POOLS == 0)) -#endif - -/** - * MEMP_STATS==1: Enable memp.c pool stats. - */ -#ifndef MEMP_STATS -#define MEMP_STATS (MEMP_MEM_MALLOC == 0) -#endif - -/** - * SYS_STATS==1: Enable system stats (sem and mbox counts, etc). - */ -#ifndef SYS_STATS -#define SYS_STATS (NO_SYS == 0) -#endif - -#else - -#define LINK_STATS 0 -#define IP_STATS 0 -#define IPFRAG_STATS 0 -#define ICMP_STATS 0 -#define IGMP_STATS 0 -#define UDP_STATS 0 -#define TCP_STATS 0 -#define MEM_STATS 0 -#define MEMP_STATS 0 -#define SYS_STATS 0 -#define LWIP_STATS_DISPLAY 0 - -#endif /* LWIP_STATS */ - -/* - --------------------------------- - ---------- PPP options ---------- - --------------------------------- -*/ -/** - * PPP_SUPPORT==1: Enable PPP. - */ -#ifndef PPP_SUPPORT -#define PPP_SUPPORT 0 -#endif - -/** - * PPPOE_SUPPORT==1: Enable PPP Over Ethernet - */ -#ifndef PPPOE_SUPPORT -#define PPPOE_SUPPORT 0 -#endif - -/** - * PPPOS_SUPPORT==1: Enable PPP Over Serial - */ -#ifndef PPPOS_SUPPORT -#define PPPOS_SUPPORT PPP_SUPPORT -#endif - -#if PPP_SUPPORT - -/** - * NUM_PPP: Max PPP sessions. - */ -#ifndef NUM_PPP -#define NUM_PPP 1 -#endif - -/** - * PAP_SUPPORT==1: Support PAP. - */ -#ifndef PAP_SUPPORT -#define PAP_SUPPORT 0 -#endif - -/** - * CHAP_SUPPORT==1: Support CHAP. - */ -#ifndef CHAP_SUPPORT -#define CHAP_SUPPORT 0 -#endif - -/** - * MSCHAP_SUPPORT==1: Support MSCHAP. CURRENTLY NOT SUPPORTED! DO NOT SET! - */ -#ifndef MSCHAP_SUPPORT -#define MSCHAP_SUPPORT 0 -#endif - -/** - * CBCP_SUPPORT==1: Support CBCP. CURRENTLY NOT SUPPORTED! DO NOT SET! - */ -#ifndef CBCP_SUPPORT -#define CBCP_SUPPORT 0 -#endif - -/** - * CCP_SUPPORT==1: Support CCP. CURRENTLY NOT SUPPORTED! DO NOT SET! - */ -#ifndef CCP_SUPPORT -#define CCP_SUPPORT 0 -#endif - -/** - * VJ_SUPPORT==1: Support VJ header compression. - */ -#ifndef VJ_SUPPORT -#define VJ_SUPPORT 0 -#endif - -/** - * MD5_SUPPORT==1: Support MD5 (see also CHAP). - */ -#ifndef MD5_SUPPORT -#define MD5_SUPPORT 0 -#endif - -/* - * Timeouts - */ -#ifndef FSM_DEFTIMEOUT -#define FSM_DEFTIMEOUT 6 /* Timeout time in seconds */ -#endif - -#ifndef FSM_DEFMAXTERMREQS -#define FSM_DEFMAXTERMREQS 2 /* Maximum Terminate-Request transmissions */ -#endif - -#ifndef FSM_DEFMAXCONFREQS -#define FSM_DEFMAXCONFREQS 10 /* Maximum Configure-Request transmissions */ -#endif - -#ifndef FSM_DEFMAXNAKLOOPS -#define FSM_DEFMAXNAKLOOPS 5 /* Maximum number of nak loops */ -#endif - -#ifndef UPAP_DEFTIMEOUT -#define UPAP_DEFTIMEOUT 6 /* Timeout (seconds) for retransmitting req */ -#endif - -#ifndef UPAP_DEFREQTIME -#define UPAP_DEFREQTIME 30 /* Time to wait for auth-req from peer */ -#endif - -#ifndef CHAP_DEFTIMEOUT -#define CHAP_DEFTIMEOUT 6 /* Timeout time in seconds */ -#endif - -#ifndef CHAP_DEFTRANSMITS -#define CHAP_DEFTRANSMITS 10 /* max # times to send challenge */ -#endif - -/* Interval in seconds between keepalive echo requests, 0 to disable. */ -#ifndef LCP_ECHOINTERVAL -#define LCP_ECHOINTERVAL 0 -#endif - -/* Number of unanswered echo requests before failure. */ -#ifndef LCP_MAXECHOFAILS -#define LCP_MAXECHOFAILS 3 -#endif - -/* Max Xmit idle time (in jiffies) before resend flag char. */ -#ifndef PPP_MAXIDLEFLAG -#define PPP_MAXIDLEFLAG 100 -#endif - -/* - * Packet sizes - * - * Note - lcp shouldn't be allowed to negotiate stuff outside these - * limits. See lcp.h in the pppd directory. - * (XXX - these constants should simply be shared by lcp.c instead - * of living in lcp.h) - */ -#define PPP_MTU 1500 /* Default MTU (size of Info field) */ -#ifndef PPP_MAXMTU -/* #define PPP_MAXMTU 65535 - (PPP_HDRLEN + PPP_FCSLEN) */ -#define PPP_MAXMTU 1500 /* Largest MTU we allow */ -#endif -#define PPP_MINMTU 64 -#define PPP_MRU 1500 /* default MRU = max length of info field */ -#define PPP_MAXMRU 1500 /* Largest MRU we allow */ -#ifndef PPP_DEFMRU -#define PPP_DEFMRU 296 /* Try for this */ -#endif -#define PPP_MINMRU 128 /* No MRUs below this */ - -#ifndef MAXNAMELEN -#define MAXNAMELEN 256 /* max length of hostname or name for auth */ -#endif -#ifndef MAXSECRETLEN -#define MAXSECRETLEN 256 /* max length of password or secret */ -#endif - -#endif /* PPP_SUPPORT */ - -/* - -------------------------------------- - ---------- Checksum options ---------- - -------------------------------------- -*/ -/** - * CHECKSUM_GEN_IP==1: Generate checksums in software for outgoing IP packets. - */ -#ifndef CHECKSUM_GEN_IP -#define CHECKSUM_GEN_IP 1 -#endif - -/** - * CHECKSUM_GEN_UDP==1: Generate checksums in software for outgoing UDP packets. - */ -#ifndef CHECKSUM_GEN_UDP -#define CHECKSUM_GEN_UDP 1 -#endif - -/** - * CHECKSUM_GEN_TCP==1: Generate checksums in software for outgoing TCP packets. - */ -#ifndef CHECKSUM_GEN_TCP -#define CHECKSUM_GEN_TCP 1 -#endif - -/** - * CHECKSUM_GEN_ICMP==1: Generate checksums in software for outgoing ICMP packets. - */ -#ifndef CHECKSUM_GEN_ICMP -#define CHECKSUM_GEN_ICMP 1 -#endif - -/** - * CHECKSUM_CHECK_IP==1: Check checksums in software for incoming IP packets. - */ -#ifndef CHECKSUM_CHECK_IP -#define CHECKSUM_CHECK_IP 1 -#endif - -/** - * CHECKSUM_CHECK_UDP==1: Check checksums in software for incoming UDP packets. - */ -#ifndef CHECKSUM_CHECK_UDP -#define CHECKSUM_CHECK_UDP 1 -#endif - -/** - * CHECKSUM_CHECK_TCP==1: Check checksums in software for incoming TCP packets. - */ -#ifndef CHECKSUM_CHECK_TCP -#define CHECKSUM_CHECK_TCP 1 -#endif - -/** - * LWIP_CHECKSUM_ON_COPY==1: Calculate checksum when copying data from - * application buffers to pbufs. - */ -#ifndef LWIP_CHECKSUM_ON_COPY -#define LWIP_CHECKSUM_ON_COPY 0 -#endif - -/* - --------------------------------------- - ---------- Hook options --------------- - --------------------------------------- -*/ - -/* Hooks are undefined by default, define them to a function if you need them. */ - -/** - * LWIP_HOOK_IP4_INPUT(pbuf, input_netif): - * - called from ip_input() (IPv4) - * - pbuf: received struct pbuf passed to ip_input() - * - input_netif: struct netif on which the packet has been received - * Return values: - * - 0: Hook has not consumed the packet, packet is processed as normal - * - != 0: Hook has consumed the packet. - * If the hook consumed the packet, 'pbuf' is in the responsibility of the hook - * (i.e. free it when done). - */ - -/** - * LWIP_HOOK_IP4_ROUTE(dest): - * - called from ip_route() (IPv4) - * - dest: destination IPv4 address - * Returns the destination netif or NULL if no destination netif is found. In - * that case, ip_route() continues as normal. - */ - -/* - --------------------------------------- - ---------- Debugging options ---------- - --------------------------------------- -*/ -/** - * LWIP_DBG_MIN_LEVEL: After masking, the value of the debug is - * compared against this value. If it is smaller, then debugging - * messages are written. - */ -#ifndef LWIP_DBG_MIN_LEVEL -#define LWIP_DBG_MIN_LEVEL LWIP_DBG_LEVEL_ALL -#endif - -/** - * LWIP_DBG_TYPES_ON: A mask that can be used to globally enable/disable - * debug messages of certain types. - */ -#ifndef LWIP_DBG_TYPES_ON -#define LWIP_DBG_TYPES_ON LWIP_DBG_ON -#endif - -/** - * ETHARP_DEBUG: Enable debugging in etharp.c. - */ -#ifndef ETHARP_DEBUG -#define ETHARP_DEBUG LWIP_DBG_OFF -#endif - -/** - * NETIF_DEBUG: Enable debugging in netif.c. - */ -#ifndef NETIF_DEBUG -#define NETIF_DEBUG LWIP_DBG_OFF -#endif - -/** - * PBUF_DEBUG: Enable debugging in pbuf.c. - */ -#ifndef PBUF_DEBUG -#define PBUF_DEBUG LWIP_DBG_OFF -#endif - -/** - * API_LIB_DEBUG: Enable debugging in api_lib.c. - */ -#ifndef API_LIB_DEBUG -#define API_LIB_DEBUG LWIP_DBG_OFF -#endif - -/** - * API_MSG_DEBUG: Enable debugging in api_msg.c. - */ -#ifndef API_MSG_DEBUG -#define API_MSG_DEBUG LWIP_DBG_OFF -#endif - -/** - * SOCKETS_DEBUG: Enable debugging in sockets.c. - */ -#ifndef SOCKETS_DEBUG -#define SOCKETS_DEBUG LWIP_DBG_OFF -#endif - -/** - * ICMP_DEBUG: Enable debugging in icmp.c. - */ -#ifndef ICMP_DEBUG -#define ICMP_DEBUG LWIP_DBG_OFF -#endif - -/** - * IGMP_DEBUG: Enable debugging in igmp.c. - */ -#ifndef IGMP_DEBUG -#define IGMP_DEBUG LWIP_DBG_OFF -#endif - -/** - * INET_DEBUG: Enable debugging in inet.c. - */ -#ifndef INET_DEBUG -#define INET_DEBUG LWIP_DBG_OFF -#endif - -/** - * IP_DEBUG: Enable debugging for IP. - */ -#ifndef IP_DEBUG -#define IP_DEBUG LWIP_DBG_OFF -#endif - -/** - * IP_REASS_DEBUG: Enable debugging in ip_frag.c for both frag & reass. - */ -#ifndef IP_REASS_DEBUG -#define IP_REASS_DEBUG LWIP_DBG_OFF -#endif - -/** - * RAW_DEBUG: Enable debugging in raw.c. - */ -#ifndef RAW_DEBUG -#define RAW_DEBUG LWIP_DBG_OFF -#endif - -/** - * MEM_DEBUG: Enable debugging in mem.c. - */ -#ifndef MEM_DEBUG -#define MEM_DEBUG LWIP_DBG_OFF -#endif - -/** - * MEMP_DEBUG: Enable debugging in memp.c. - */ -#ifndef MEMP_DEBUG -#define MEMP_DEBUG LWIP_DBG_OFF -#endif - -/** - * SYS_DEBUG: Enable debugging in sys.c. - */ -#ifndef SYS_DEBUG -#define SYS_DEBUG LWIP_DBG_OFF -#endif - -/** - * TIMERS_DEBUG: Enable debugging in timers.c. - */ -#ifndef TIMERS_DEBUG -#define TIMERS_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_DEBUG: Enable debugging for TCP. - */ -#ifndef TCP_DEBUG -#define TCP_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_INPUT_DEBUG: Enable debugging in tcp_in.c for incoming debug. - */ -#ifndef TCP_INPUT_DEBUG -#define TCP_INPUT_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_FR_DEBUG: Enable debugging in tcp_in.c for fast retransmit. - */ -#ifndef TCP_FR_DEBUG -#define TCP_FR_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_RTO_DEBUG: Enable debugging in TCP for retransmit - * timeout. - */ -#ifndef TCP_RTO_DEBUG -#define TCP_RTO_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_CWND_DEBUG: Enable debugging for TCP congestion window. - */ -#ifndef TCP_CWND_DEBUG -#define TCP_CWND_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_WND_DEBUG: Enable debugging in tcp_in.c for window updating. - */ -#ifndef TCP_WND_DEBUG -#define TCP_WND_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_OUTPUT_DEBUG: Enable debugging in tcp_out.c output functions. - */ -#ifndef TCP_OUTPUT_DEBUG -#define TCP_OUTPUT_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_RST_DEBUG: Enable debugging for TCP with the RST message. - */ -#ifndef TCP_RST_DEBUG -#define TCP_RST_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCP_QLEN_DEBUG: Enable debugging for TCP queue lengths. - */ -#ifndef TCP_QLEN_DEBUG -#define TCP_QLEN_DEBUG LWIP_DBG_OFF -#endif - -/** - * UDP_DEBUG: Enable debugging in UDP. - */ -#ifndef UDP_DEBUG -#define UDP_DEBUG LWIP_DBG_OFF -#endif - -/** - * TCPIP_DEBUG: Enable debugging in tcpip.c. - */ -#ifndef TCPIP_DEBUG -#define TCPIP_DEBUG LWIP_DBG_OFF -#endif - -/** - * PPP_DEBUG: Enable debugging for PPP. - */ -#ifndef PPP_DEBUG -#define PPP_DEBUG LWIP_DBG_OFF -#endif - -/** - * SLIP_DEBUG: Enable debugging in slipif.c. - */ -#ifndef SLIP_DEBUG -#define SLIP_DEBUG LWIP_DBG_OFF -#endif - -/** - * DHCP_DEBUG: Enable debugging in dhcp.c. - */ -#ifndef DHCP_DEBUG -#define DHCP_DEBUG LWIP_DBG_OFF -#endif - -/** - * AUTOIP_DEBUG: Enable debugging in autoip.c. - */ -#ifndef AUTOIP_DEBUG -#define AUTOIP_DEBUG LWIP_DBG_OFF -#endif - -/** - * SNMP_MSG_DEBUG: Enable debugging for SNMP messages. - */ -#ifndef SNMP_MSG_DEBUG -#define SNMP_MSG_DEBUG LWIP_DBG_OFF -#endif - -/** - * SNMP_MIB_DEBUG: Enable debugging for SNMP MIBs. - */ -#ifndef SNMP_MIB_DEBUG -#define SNMP_MIB_DEBUG LWIP_DBG_OFF -#endif - -/** - * DNS_DEBUG: Enable debugging for DNS. - */ -#ifndef DNS_DEBUG -#define DNS_DEBUG LWIP_DBG_OFF -#endif - -#endif /* __LWIPOPT_H__ */ diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/mcuconf.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/mcuconf.h deleted file mode 100644 index fe9e360ee..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/mcuconf.h +++ /dev/null @@ -1,391 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#ifndef MCUCONF_H -#define MCUCONF_H - -/* - * STM32F7xx drivers configuration. - * The following settings override the default settings present in - * the various device driver implementation headers. - * Note that the settings for each driver only have effect if the whole - * driver is enabled in halconf.h. - * - * IRQ priorities: - * 15...0 Lowest...Highest. - * - * DMA priorities: - * 0...3 Lowest...Highest. - */ - -#define STM32F7xx_MCUCONF - -/* - * HAL driver system settings. - */ -#define STM32_NO_INIT FALSE -#define STM32_PVD_ENABLE FALSE -#define STM32_PLS STM32_PLS_LEV0 -#define STM32_BKPRAM_ENABLE FALSE -#define STM32_HSI_ENABLED TRUE -#define STM32_LSI_ENABLED FALSE -#define STM32_HSE_ENABLED TRUE -#define STM32_LSE_ENABLED TRUE -#define STM32_CLOCK48_REQUIRED TRUE -#define STM32_SW STM32_SW_PLL -#define STM32_PLLSRC STM32_PLLSRC_HSE -#define STM32_PLLM_VALUE 25 -#define STM32_PLLN_VALUE 432 -#define STM32_PLLP_VALUE 2 -#define STM32_PLLQ_VALUE 9 -#define STM32_HPRE STM32_HPRE_DIV1 -#define STM32_PPRE1 STM32_PPRE1_DIV4 -#define STM32_PPRE2 STM32_PPRE2_DIV2 -#define STM32_RTCSEL STM32_RTCSEL_LSE -#define STM32_RTCPRE_VALUE 25 -#define STM32_MCO1SEL STM32_MCO1SEL_HSI -#define STM32_MCO1PRE STM32_MCO1PRE_DIV1 -#define STM32_MCO2SEL STM32_MCO2SEL_SYSCLK -#define STM32_MCO2PRE STM32_MCO2PRE_DIV4 -#define STM32_I2SSRC STM32_I2SSRC_OFF -#define STM32_PLLI2SN_VALUE 192 -#define STM32_PLLI2SP_VALUE 4 -#define STM32_PLLI2SQ_VALUE 4 -#define STM32_PLLI2SR_VALUE 4 -#define STM32_PLLI2SDIVQ_VALUE 2 -#define STM32_PLLSAIN_VALUE 192 -#define STM32_PLLSAIP_VALUE 4 -#define STM32_PLLSAIQ_VALUE 4 -#define STM32_PLLSAIR_VALUE 4 -#define STM32_PLLSAIDIVQ_VALUE 2 -#define STM32_PLLSAIDIVR_VALUE 2 -#define STM32_SAI1SEL STM32_SAI1SEL_OFF -#define STM32_SAI2SEL STM32_SAI2SEL_OFF -#define STM32_LCDTFT_REQUIRED FALSE -#define STM32_USART1SEL STM32_USART1SEL_PCLK2 -#define STM32_USART2SEL STM32_USART2SEL_PCLK1 -#define STM32_USART3SEL STM32_USART3SEL_PCLK1 -#define STM32_UART4SEL STM32_UART4SEL_PCLK1 -#define STM32_UART5SEL STM32_UART5SEL_PCLK1 -#define STM32_USART6SEL STM32_USART6SEL_PCLK2 -#define STM32_UART7SEL STM32_UART7SEL_PCLK1 -#define STM32_UART8SEL STM32_UART8SEL_PCLK1 -#define STM32_I2C1SEL STM32_I2C1SEL_PCLK1 -#define STM32_I2C2SEL STM32_I2C2SEL_PCLK1 -#define STM32_I2C3SEL STM32_I2C3SEL_PCLK1 -#define STM32_I2C4SEL STM32_I2C4SEL_PCLK1 -#define STM32_LPTIM1SEL STM32_LPTIM1SEL_PCLK1 -#define STM32_CECSEL STM32_CECSEL_LSE -#define STM32_CK48MSEL STM32_CK48MSEL_PLL -#define STM32_SDMMCSEL STM32_SDMMCSEL_PLL48CLK -#define STM32_SRAM2_NOCACHE FALSE - -/* - * ADC driver system settings. - */ -#define STM32_ADC_ADCPRE ADC_CCR_ADCPRE_DIV4 -#define STM32_ADC_USE_ADC1 FALSE -#define STM32_ADC_USE_ADC2 FALSE -#define STM32_ADC_USE_ADC3 FALSE -#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(2, 4) -#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(2, 2) -#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(2, 1) -#define STM32_ADC_ADC1_DMA_PRIORITY 2 -#define STM32_ADC_ADC2_DMA_PRIORITY 2 -#define STM32_ADC_ADC3_DMA_PRIORITY 2 -#define STM32_ADC_IRQ_PRIORITY 6 -#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 6 -#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 6 -#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 6 - -/* - * CAN driver system settings. - */ -#define STM32_CAN_USE_CAN1 FALSE -#define STM32_CAN_USE_CAN2 FALSE -#define STM32_CAN_USE_CAN3 FALSE -#define STM32_CAN_CAN1_IRQ_PRIORITY 11 -#define STM32_CAN_CAN2_IRQ_PRIORITY 11 -#define STM32_CAN_CAN3_IRQ_PRIORITY 11 - -/* - * DAC driver system settings. - */ -#define STM32_DAC_DUAL_MODE FALSE -#define STM32_DAC_USE_DAC1_CH1 FALSE -#define STM32_DAC_USE_DAC1_CH2 FALSE -#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10 -#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10 -#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2 -#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2 -#define STM32_DAC_DAC1_CH1_DMA_STREAM STM32_DMA_STREAM_ID(1, 5) -#define STM32_DAC_DAC1_CH2_DMA_STREAM STM32_DMA_STREAM_ID(1, 6) - -/* - * EXT driver system settings. - */ -#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI17_IRQ_PRIORITY 15 -#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI20_IRQ_PRIORITY 6 -#define STM32_EXT_EXTI21_IRQ_PRIORITY 15 -#define STM32_EXT_EXTI22_IRQ_PRIORITY 15 - -/* - * GPT driver system settings. - */ -#define STM32_GPT_USE_TIM1 FALSE -#define STM32_GPT_USE_TIM2 FALSE -#define STM32_GPT_USE_TIM3 FALSE -#define STM32_GPT_USE_TIM4 FALSE -#define STM32_GPT_USE_TIM5 FALSE -#define STM32_GPT_USE_TIM6 FALSE -#define STM32_GPT_USE_TIM7 FALSE -#define STM32_GPT_USE_TIM8 FALSE -#define STM32_GPT_USE_TIM9 FALSE -#define STM32_GPT_USE_TIM11 FALSE -#define STM32_GPT_USE_TIM12 FALSE -#define STM32_GPT_USE_TIM14 FALSE -#define STM32_GPT_TIM1_IRQ_PRIORITY 7 -#define STM32_GPT_TIM2_IRQ_PRIORITY 7 -#define STM32_GPT_TIM3_IRQ_PRIORITY 7 -#define STM32_GPT_TIM4_IRQ_PRIORITY 7 -#define STM32_GPT_TIM5_IRQ_PRIORITY 7 -#define STM32_GPT_TIM6_IRQ_PRIORITY 7 -#define STM32_GPT_TIM7_IRQ_PRIORITY 7 -#define STM32_GPT_TIM8_IRQ_PRIORITY 7 -#define STM32_GPT_TIM9_IRQ_PRIORITY 7 -#define STM32_GPT_TIM11_IRQ_PRIORITY 7 -#define STM32_GPT_TIM12_IRQ_PRIORITY 7 -#define STM32_GPT_TIM14_IRQ_PRIORITY 7 - -/* - * I2C driver system settings. - */ -#define STM32_I2C_USE_I2C1 FALSE -#define STM32_I2C_USE_I2C2 FALSE -#define STM32_I2C_USE_I2C3 FALSE -#define STM32_I2C_USE_I2C4 FALSE -#define STM32_I2C_BUSY_TIMEOUT 50 -#define STM32_I2C_I2C1_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0) -#define STM32_I2C_I2C1_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6) -#define STM32_I2C_I2C2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2) -#define STM32_I2C_I2C2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7) -#define STM32_I2C_I2C3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2) -#define STM32_I2C_I2C3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4) -#define STM32_I2C_I2C4_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2) -#define STM32_I2C_I2C4_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 5) -#define STM32_I2C_I2C1_IRQ_PRIORITY 5 -#define STM32_I2C_I2C2_IRQ_PRIORITY 5 -#define STM32_I2C_I2C3_IRQ_PRIORITY 5 -#define STM32_I2C_I2C4_IRQ_PRIORITY 5 -#define STM32_I2C_I2C1_DMA_PRIORITY 3 -#define STM32_I2C_I2C2_DMA_PRIORITY 3 -#define STM32_I2C_I2C3_DMA_PRIORITY 3 -#define STM32_I2C_I2C4_DMA_PRIORITY 3 -#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") - -/* - * ICU driver system settings. - */ -#define STM32_ICU_USE_TIM1 FALSE -#define STM32_ICU_USE_TIM2 FALSE -#define STM32_ICU_USE_TIM3 FALSE -#define STM32_ICU_USE_TIM4 FALSE -#define STM32_ICU_USE_TIM5 FALSE -#define STM32_ICU_USE_TIM8 FALSE -#define STM32_ICU_USE_TIM9 FALSE -#define STM32_ICU_TIM1_IRQ_PRIORITY 7 -#define STM32_ICU_TIM2_IRQ_PRIORITY 7 -#define STM32_ICU_TIM3_IRQ_PRIORITY 7 -#define STM32_ICU_TIM4_IRQ_PRIORITY 7 -#define STM32_ICU_TIM5_IRQ_PRIORITY 7 -#define STM32_ICU_TIM8_IRQ_PRIORITY 7 -#define STM32_ICU_TIM9_IRQ_PRIORITY 7 - -/* - * MAC driver system settings. - */ -#define STM32_MAC_TRANSMIT_BUFFERS 2 -#define STM32_MAC_RECEIVE_BUFFERS 4 -#define STM32_MAC_BUFFERS_SIZE 1522 -#define STM32_MAC_PHY_TIMEOUT 100 -#define STM32_MAC_ETH1_CHANGE_PHY_STATE TRUE -#define STM32_MAC_ETH1_IRQ_PRIORITY 13 -#define STM32_MAC_IP_CHECKSUM_OFFLOAD 0 - -/* - * PWM driver system settings. - */ -#define STM32_PWM_USE_ADVANCED FALSE -#define STM32_PWM_USE_TIM1 FALSE -#define STM32_PWM_USE_TIM2 FALSE -#define STM32_PWM_USE_TIM3 FALSE -#define STM32_PWM_USE_TIM4 FALSE -#define STM32_PWM_USE_TIM5 FALSE -#define STM32_PWM_USE_TIM8 FALSE -#define STM32_PWM_USE_TIM9 FALSE -#define STM32_PWM_TIM1_IRQ_PRIORITY 7 -#define STM32_PWM_TIM2_IRQ_PRIORITY 7 -#define STM32_PWM_TIM3_IRQ_PRIORITY 7 -#define STM32_PWM_TIM4_IRQ_PRIORITY 7 -#define STM32_PWM_TIM5_IRQ_PRIORITY 7 -#define STM32_PWM_TIM8_IRQ_PRIORITY 7 -#define STM32_PWM_TIM9_IRQ_PRIORITY 7 - -/* - * SDC driver system settings. - */ -#define STM32_SDC_USE_SDMMC1 TRUE -#define STM32_SDC_SDMMC_UNALIGNED_SUPPORT TRUE -#define STM32_SDC_SDMMC_WRITE_TIMEOUT 1000 -#define STM32_SDC_SDMMC_READ_TIMEOUT 1000 -#define STM32_SDC_SDMMC_CLOCK_DELAY 10 -#define STM32_SDC_SDMMC1_DMA_STREAM STM32_DMA_STREAM_ID(2, 3) -#define STM32_SDC_SDMMC1_DMA_PRIORITY 3 -#define STM32_SDC_SDMMC1_IRQ_PRIORITY 9 - -/* - * SERIAL driver system settings. - */ -#define STM32_SERIAL_USE_USART1 TRUE -#define STM32_SERIAL_USE_USART2 FALSE -#define STM32_SERIAL_USE_USART3 FALSE -#define STM32_SERIAL_USE_UART4 FALSE -#define STM32_SERIAL_USE_UART5 FALSE -#define STM32_SERIAL_USE_USART6 FALSE -#define STM32_SERIAL_USE_UART7 FALSE -#define STM32_SERIAL_USE_UART8 FALSE -#define STM32_SERIAL_USART1_PRIORITY 12 -#define STM32_SERIAL_USART2_PRIORITY 12 -#define STM32_SERIAL_USART3_PRIORITY 12 -#define STM32_SERIAL_UART4_PRIORITY 12 -#define STM32_SERIAL_UART5_PRIORITY 12 -#define STM32_SERIAL_USART6_PRIORITY 12 -#define STM32_SERIAL_UART7_PRIORITY 12 -#define STM32_SERIAL_UART8_PRIORITY 12 - -/* - * SPI driver system settings. - */ -#define STM32_SPI_USE_SPI1 FALSE -#define STM32_SPI_USE_SPI2 FALSE -#define STM32_SPI_USE_SPI3 FALSE -#define STM32_SPI_USE_SPI4 FALSE -#define STM32_SPI_USE_SPI5 FALSE -#define STM32_SPI_USE_SPI6 FALSE -#define STM32_SPI_SPI1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 0) -#define STM32_SPI_SPI1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 3) -#define STM32_SPI_SPI2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3) -#define STM32_SPI_SPI2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4) -#define STM32_SPI_SPI3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0) -#define STM32_SPI_SPI3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7) -#define STM32_SPI_SPI4_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 0) -#define STM32_SPI_SPI4_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 1) -#define STM32_SPI_SPI5_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 3) -#define STM32_SPI_SPI5_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 4) -#define STM32_SPI_SPI6_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 6) -#define STM32_SPI_SPI6_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 5) -#define STM32_SPI_SPI1_DMA_PRIORITY 1 -#define STM32_SPI_SPI2_DMA_PRIORITY 1 -#define STM32_SPI_SPI3_DMA_PRIORITY 1 -#define STM32_SPI_SPI4_DMA_PRIORITY 1 -#define STM32_SPI_SPI5_DMA_PRIORITY 1 -#define STM32_SPI_SPI6_DMA_PRIORITY 1 -#define STM32_SPI_SPI1_IRQ_PRIORITY 10 -#define STM32_SPI_SPI2_IRQ_PRIORITY 10 -#define STM32_SPI_SPI3_IRQ_PRIORITY 10 -#define STM32_SPI_SPI4_IRQ_PRIORITY 10 -#define STM32_SPI_SPI5_IRQ_PRIORITY 10 -#define STM32_SPI_SPI6_IRQ_PRIORITY 10 -#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") - -/* - * ST driver system settings. - */ -#define STM32_ST_IRQ_PRIORITY 8 -#define STM32_ST_USE_TIMER 2 - -/* - * UART driver system settings. - */ -#define STM32_UART_USE_USART1 FALSE -#define STM32_UART_USE_USART2 FALSE -#define STM32_UART_USE_USART3 FALSE -#define STM32_UART_USE_UART4 FALSE -#define STM32_UART_USE_UART5 FALSE -#define STM32_UART_USE_USART6 FALSE -#define STM32_UART_USE_UART7 FALSE -#define STM32_UART_USE_UART8 FALSE -#define STM32_UART_USART1_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 5) -#define STM32_UART_USART1_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7) -#define STM32_UART_USART2_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 5) -#define STM32_UART_USART2_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6) -#define STM32_UART_USART3_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 1) -#define STM32_UART_USART3_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3) -#define STM32_UART_UART4_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 2) -#define STM32_UART_UART4_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 4) -#define STM32_UART_UART5_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0) -#define STM32_UART_UART5_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 7) -#define STM32_UART_USART6_RX_DMA_STREAM STM32_DMA_STREAM_ID(2, 2) -#define STM32_UART_USART6_TX_DMA_STREAM STM32_DMA_STREAM_ID(2, 7) -#define STM32_UART_UART7_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 3) -#define STM32_UART_UART7_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 1) -#define STM32_UART_UART8_RX_DMA_STREAM STM32_DMA_STREAM_ID(1, 6) -#define STM32_UART_UART8_TX_DMA_STREAM STM32_DMA_STREAM_ID(1, 0) -#define STM32_UART_USART1_IRQ_PRIORITY 12 -#define STM32_UART_USART2_IRQ_PRIORITY 12 -#define STM32_UART_USART3_IRQ_PRIORITY 12 -#define STM32_UART_UART4_IRQ_PRIORITY 12 -#define STM32_UART_UART5_IRQ_PRIORITY 12 -#define STM32_UART_USART6_IRQ_PRIORITY 12 -#define STM32_UART_USART1_DMA_PRIORITY 0 -#define STM32_UART_USART2_DMA_PRIORITY 0 -#define STM32_UART_USART3_DMA_PRIORITY 0 -#define STM32_UART_UART4_DMA_PRIORITY 0 -#define STM32_UART_UART5_DMA_PRIORITY 0 -#define STM32_UART_USART6_DMA_PRIORITY 0 -#define STM32_UART_UART7_DMA_PRIORITY 0 -#define STM32_UART_UART8_DMA_PRIORITY 0 -#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") - -/* - * USB driver system settings. - */ -#define STM32_USB_USE_OTG1 FALSE -#define STM32_USB_USE_OTG2 TRUE -#define STM32_USB_OTG1_IRQ_PRIORITY 14 -#define STM32_USB_OTG2_IRQ_PRIORITY 14 -#define STM32_USB_OTG1_RX_FIFO_SIZE 512 -#define STM32_USB_OTG2_RX_FIFO_SIZE 1024 -#define STM32_USB_OTG_THREAD_PRIO LOWPRIO -#define STM32_USB_OTG_THREAD_STACK_SIZE 128 -#define STM32_USB_OTGFIFO_FILL_BASEPRI 0 - -/* - * WDG driver system settings. - */ -#define STM32_WDG_USE_IWDG FALSE - -#endif /* MCUCONF_H */ diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.c b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.c deleted file mode 100644 index bb05f43c8..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.c +++ /dev/null @@ -1,342 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#include "hal.h" - -/* Virtual serial port over USB.*/ -SerialUSBDriver SDU2; - -/* - * Endpoints to be used for USBD2. - */ -#define USBD2_DATA_REQUEST_EP 1 -#define USBD2_DATA_AVAILABLE_EP 1 -#define USBD2_INTERRUPT_REQUEST_EP 2 - -/* - * USB Device Descriptor. - */ -static const uint8_t vcom_device_descriptor_data[18] = { - USB_DESC_DEVICE (0x0200, /* bcdUSB (2.0). */ - 0x02, /* bDeviceClass (CDC). */ - 0x00, /* bDeviceSubClass. */ - 0x00, /* bDeviceProtocol. */ - 0x40, /* bMaxPacketSize. */ - 0x0483, /* idVendor (ST). */ - 0x5740, /* idProduct. */ - 0x0200, /* bcdDevice. */ - 1, /* iManufacturer. */ - 2, /* iProduct. */ - 3, /* iSerialNumber. */ - 1) /* bNumConfigurations. */ -}; - -/* - * Device Descriptor wrapper. - */ -static const USBDescriptor vcom_device_descriptor = { - sizeof vcom_device_descriptor_data, - vcom_device_descriptor_data -}; - -/* Configuration Descriptor tree for a CDC.*/ -static const uint8_t vcom_configuration_descriptor_data[67] = { - /* Configuration Descriptor.*/ - USB_DESC_CONFIGURATION(67, /* wTotalLength. */ - 0x02, /* bNumInterfaces. */ - 0x01, /* bConfigurationValue. */ - 0, /* iConfiguration. */ - 0xC0, /* bmAttributes (self powered). */ - 50), /* bMaxPower (100mA). */ - /* Interface Descriptor.*/ - USB_DESC_INTERFACE (0x00, /* bInterfaceNumber. */ - 0x00, /* bAlternateSetting. */ - 0x01, /* bNumEndpoints. */ - 0x02, /* bInterfaceClass (Communications - Interface Class, CDC section - 4.2). */ - 0x02, /* bInterfaceSubClass (Abstract - Control Model, CDC section 4.3). */ - 0x01, /* bInterfaceProtocol (AT commands, - CDC section 4.4). */ - 0), /* iInterface. */ - /* Header Functional Descriptor (CDC section 5.2.3).*/ - USB_DESC_BYTE (5), /* bLength. */ - USB_DESC_BYTE (0x24), /* bDescriptorType (CS_INTERFACE). */ - USB_DESC_BYTE (0x00), /* bDescriptorSubtype (Header - Functional Descriptor. */ - USB_DESC_BCD (0x0110), /* bcdCDC. */ - /* Call Management Functional Descriptor. */ - USB_DESC_BYTE (5), /* bFunctionLength. */ - USB_DESC_BYTE (0x24), /* bDescriptorType (CS_INTERFACE). */ - USB_DESC_BYTE (0x01), /* bDescriptorSubtype (Call Management - Functional Descriptor). */ - USB_DESC_BYTE (0x00), /* bmCapabilities (D0+D1). */ - USB_DESC_BYTE (0x01), /* bDataInterface. */ - /* ACM Functional Descriptor.*/ - USB_DESC_BYTE (4), /* bFunctionLength. */ - USB_DESC_BYTE (0x24), /* bDescriptorType (CS_INTERFACE). */ - USB_DESC_BYTE (0x02), /* bDescriptorSubtype (Abstract - Control Management Descriptor). */ - USB_DESC_BYTE (0x02), /* bmCapabilities. */ - /* Union Functional Descriptor.*/ - USB_DESC_BYTE (5), /* bFunctionLength. */ - USB_DESC_BYTE (0x24), /* bDescriptorType (CS_INTERFACE). */ - USB_DESC_BYTE (0x06), /* bDescriptorSubtype (Union - Functional Descriptor). */ - USB_DESC_BYTE (0x00), /* bMasterInterface (Communication - Class Interface). */ - USB_DESC_BYTE (0x01), /* bSlaveInterface0 (Data Class - Interface). */ - /* Endpoint 2 Descriptor.*/ - USB_DESC_ENDPOINT (USBD2_INTERRUPT_REQUEST_EP|0x80, - 0x03, /* bmAttributes (Interrupt). */ - 0x0008, /* wMaxPacketSize. */ - 0xFF), /* bInterval. */ - /* Interface Descriptor.*/ - USB_DESC_INTERFACE (0x01, /* bInterfaceNumber. */ - 0x00, /* bAlternateSetting. */ - 0x02, /* bNumEndpoints. */ - 0x0A, /* bInterfaceClass (Data Class - Interface, CDC section 4.5). */ - 0x00, /* bInterfaceSubClass (CDC section - 4.6). */ - 0x00, /* bInterfaceProtocol (CDC section - 4.7). */ - 0x00), /* iInterface. */ - /* Endpoint 3 Descriptor.*/ - USB_DESC_ENDPOINT (USBD2_DATA_AVAILABLE_EP, /* bEndpointAddress.*/ - 0x02, /* bmAttributes (Bulk). */ - 0x0040, /* wMaxPacketSize. */ - 0x00), /* bInterval. */ - /* Endpoint 1 Descriptor.*/ - USB_DESC_ENDPOINT (USBD2_DATA_REQUEST_EP|0x80, /* bEndpointAddress.*/ - 0x02, /* bmAttributes (Bulk). */ - 0x0040, /* wMaxPacketSize. */ - 0x00) /* bInterval. */ -}; - -/* - * Configuration Descriptor wrapper. - */ -static const USBDescriptor vcom_configuration_descriptor = { - sizeof vcom_configuration_descriptor_data, - vcom_configuration_descriptor_data -}; - -/* - * U.S. English language identifier. - */ -static const uint8_t vcom_string0[] = { - USB_DESC_BYTE(4), /* bLength. */ - USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType. */ - USB_DESC_WORD(0x0409) /* wLANGID (U.S. English). */ -}; - -/* - * Vendor string. - */ -static const uint8_t vcom_string1[] = { - USB_DESC_BYTE(38), /* bLength. */ - USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType. */ - 'S', 0, 'T', 0, 'M', 0, 'i', 0, 'c', 0, 'r', 0, 'o', 0, 'e', 0, - 'l', 0, 'e', 0, 'c', 0, 't', 0, 'r', 0, 'o', 0, 'n', 0, 'i', 0, - 'c', 0, 's', 0 -}; - -/* - * Device Description string. - */ -static const uint8_t vcom_string2[] = { - USB_DESC_BYTE(56), /* bLength. */ - USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType. */ - 'C', 0, 'h', 0, 'i', 0, 'b', 0, 'i', 0, 'O', 0, 'S', 0, '/', 0, - 'R', 0, 'T', 0, ' ', 0, 'V', 0, 'i', 0, 'r', 0, 't', 0, 'u', 0, - 'a', 0, 'l', 0, ' ', 0, 'C', 0, 'O', 0, 'M', 0, ' ', 0, 'P', 0, - 'o', 0, 'r', 0, 't', 0 -}; - -/* - * Serial Number string. - */ -static const uint8_t vcom_string3[] = { - USB_DESC_BYTE(8), /* bLength. */ - USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType. */ - '0' + CH_KERNEL_MAJOR, 0, - '0' + CH_KERNEL_MINOR, 0, - '0' + CH_KERNEL_PATCH, 0 -}; - -/* - * Strings wrappers array. - */ -static const USBDescriptor vcom_strings[] = { - {sizeof vcom_string0, vcom_string0}, - {sizeof vcom_string1, vcom_string1}, - {sizeof vcom_string2, vcom_string2}, - {sizeof vcom_string3, vcom_string3} -}; - -/* - * Handles the GET_DESCRIPTOR callback. All required descriptors must be - * handled here. - */ -static const USBDescriptor *get_descriptor(USBDriver *usbp, - uint8_t dtype, - uint8_t dindex, - uint16_t lang) { - - (void)usbp; - (void)lang; - switch (dtype) { - case USB_DESCRIPTOR_DEVICE: - return &vcom_device_descriptor; - case USB_DESCRIPTOR_CONFIGURATION: - return &vcom_configuration_descriptor; - case USB_DESCRIPTOR_STRING: - if (dindex < 4) - return &vcom_strings[dindex]; - } - return NULL; -} - -/** - * @brief IN EP1 state. - */ -static USBInEndpointState ep1instate; - -/** - * @brief OUT EP1 state. - */ -static USBOutEndpointState ep1outstate; - -/** - * @brief EP1 initialization structure (both IN and OUT). - */ -static const USBEndpointConfig ep1config = { - USB_EP_MODE_TYPE_BULK, - NULL, - sduDataTransmitted, - sduDataReceived, - 0x0040, - 0x0040, - &ep1instate, - &ep1outstate, - 4, - NULL -}; - -/** - * @brief IN EP2 state. - */ -static USBInEndpointState ep2instate; - -/** - * @brief EP2 initialization structure (IN only). - */ -static const USBEndpointConfig ep2config = { - USB_EP_MODE_TYPE_INTR, - NULL, - sduInterruptTransmitted, - NULL, - 0x0010, - 0x0000, - &ep2instate, - NULL, - 1, - NULL -}; - -/* - * Handles the USB driver global events. - */ -static void usb_event(USBDriver *usbp, usbevent_t event) { - extern SerialUSBDriver SDU2; - - switch (event) { - case USB_EVENT_ADDRESS: - return; - case USB_EVENT_CONFIGURED: - chSysLockFromISR(); - - /* Enables the endpoints specified into the configuration. - Note, this callback is invoked from an ISR so I-Class functions - must be used.*/ - usbInitEndpointI(usbp, USBD2_DATA_REQUEST_EP, &ep1config); - usbInitEndpointI(usbp, USBD2_INTERRUPT_REQUEST_EP, &ep2config); - - /* Resetting the state of the CDC subsystem.*/ - sduConfigureHookI(&SDU2); - - chSysUnlockFromISR(); - return; - case USB_EVENT_RESET: - /* Falls into.*/ - case USB_EVENT_UNCONFIGURED: - /* Falls into.*/ - case USB_EVENT_SUSPEND: - chSysLockFromISR(); - - /* Disconnection event on suspend.*/ - sduSuspendHookI(&SDU2); - - chSysUnlockFromISR(); - return; - case USB_EVENT_WAKEUP: - chSysLockFromISR(); - - /* Disconnection event on suspend.*/ - sduWakeupHookI(&SDU2); - - chSysUnlockFromISR(); - return; - case USB_EVENT_STALLED: - return; - } - return; -} - -/* - * Handles the USB driver global events. - */ -static void sof_handler(USBDriver *usbp) { - - (void)usbp; - - osalSysLockFromISR(); - sduSOFHookI(&SDU2); - osalSysUnlockFromISR(); -} - -/* - * USB driver configuration. - */ -const USBConfig usbcfg = { - usb_event, - get_descriptor, - sduRequestsHook, - sof_handler -}; - -/* - * Serial over USB driver configuration. - */ -const SerialUSBConfig serusbcfg = { - &USBD2, - USBD2_DATA_REQUEST_EP, - USBD2_DATA_AVAILABLE_EP, - USBD2_INTERRUPT_REQUEST_EP -}; diff --git a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.h b/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.h deleted file mode 100644 index d23b83c25..000000000 --- a/demos/STM32/RT-STM32F746G-DISCOVERY-LWIP-FATFS-USB/usbcfg.h +++ /dev/null @@ -1,26 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#ifndef USBCFG_H -#define USBCFG_H - -extern const USBConfig usbcfg; -extern SerialUSBConfig serusbcfg; -extern SerialUSBDriver SDU2; - -#endif /* USBCFG_H */ - -/** @} */ -- cgit v1.2.3