/*
    Copyright (C) 2014..2017 Marco Veeneman

    Licensed under the Apache License, Version 2.0 (the "License");
    you may not use this file except in compliance with the License.
    You may obtain a copy of the License at

        http://www.apache.org/licenses/LICENSE-2.0

    Unless required by applicable law or agreed to in writing, software
    distributed under the License is distributed on an "AS IS" BASIS,
    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
    See the License for the specific language governing permissions and
    limitations under the License.
*/

/**
 * @file    TIVA/TM4C123x/hal_lld.c
 * @brief   TM4C123x HAL Driver subsystem low level driver source.
 *
 * @addtogroup HAL
 * @{
 */

#include "hal.h"

/*===========================================================================*/
/* Driver local definitions.                                                 */
/*===========================================================================*/

/*===========================================================================*/
/* Driver exported variables.                                                */
/*===========================================================================*/

/*===========================================================================*/
/* Driver local variables and types.                                         */
/*===========================================================================*/

/*===========================================================================*/
/* Driver local functions.                                                   */
/*===========================================================================*/

/*===========================================================================*/
/* Driver interrupt handlers.                                                */
/*===========================================================================*/

/*===========================================================================*/
/* Driver exported functions.                                                */
/*===========================================================================*/

/**
 * @brief   Low level HAL driver initialization.
 *
 * @notapi
 */
void hal_lld_init(void)
{
}

/**
 * @brief   TM4C123x clocks and PLL initialization.
 * @note    All the involved constants come from the file @p board.h and 
 *          @p mcuconf.h.
 * @note    This function should be invoked just after the system reset.
 *
 * @special
 */
void tiva_clock_init(void)
{
  uint32_t rcc, rcc2, i;

  /* 1. Bypass the PLL and system clock divider by setting the BYPASS bit and
   * clearing the USESYSDIV bit in the RCC register, thereby configuring the
   * microcontroller to run off a "raw" clock source and allowing for the new
   * PLL configuration to be validated before switching the system clock to the
   * PLL. */
  /* read */

  rcc = HWREG(SYSCTL_RCC);
  rcc2 = HWREG(SYSCTL_RCC2);
  
  /* modify */
  rcc |= SYSCTL_RCC_BYPASS;
  rcc &= ~SYSCTL_RCC_USESYSDIV;
  rcc2 |= SYSCTL_RCC2_BYPASS2 | SYSCTL_RCC2_USERCC2;
  
  /* write */
  HWREG(SYSCTL_RCC) = rcc;
  HWREG(SYSCTL_RCC2) = rcc2;

  /* 2 Select the crystal value (XTAL) and oscillator source (OSCSRC), and
   * clear the PWRDN bit in RCC and RCC2. Setting the XTAL field automatically
   * pulls valid PLL configuration data for the appropriate crystal, and
   * clearing the PWRDN bit powers and enables the PLL and its output. */
  /* modify */
  rcc &= ~(SYSCTL_RCC_OSCSRC_M | SYSCTL_RCC_XTAL_M | SYSCTL_RCC_PWRDN | SYSCTL_RCC_MOSCDIS);
  rcc |= ((TIVA_XTAL | TIVA_OSCSRC | TIVA_MOSCDIS) & (SYSCTL_RCC_XTAL_M | SYSCTL_RCC_OSCSRC_M | SYSCTL_RCC_MOSCDIS));
  rcc2 &= ~(SYSCTL_RCC2_OSCSRC2_M | SYSCTL_RCC2_PWRDN2);
  rcc2 |= ((TIVA_OSCSRC | TIVA_DIV400) & (SYSCTL_RCC2_OSCSRC2_M | SYSCTL_RCC2_DIV400));
  
  /* write */
  HWREG(SYSCTL_RCC) = rcc;
  HWREG(SYSCTL_RCC2) = rcc2;
  for(i = 100000; i; i--);

  /* 3. Select the desired system divider (SYSDIV) in RCC and RCC2 and set the
   * USESYSDIV bit in RCC. The SYSDIV field determines the system frequency for
   * the microcontroller. */
  /* modify */
  rcc &= ~SYSCTL_RCC_SYSDIV_M;
  rcc |= (TIVA_SYSDIV & SYSCTL_RCC_SYSDIV_M) | SYSCTL_RCC_USESYSDIV;
  rcc2 &= ~(SYSCTL_RCC2_SYSDIV2_M | SYSCTL_RCC2_SYSDIV2LSB);
  rcc2 |= ((TIVA_SYSDIV2 | TIVA_SYSDIV2LSB) & (SYSCTL_RCC2_SYSDIV2_M | SYSCTL_RCC2_SYSDIV2LSB));
  
  /* write */
  HWREG(SYSCTL_RCC) = rcc;
  HWREG(SYSCTL_RCC2) = rcc2;

  /* 4. Wait for the PLL to lock by polling the PLLLRIS bit in the Raw
   * Interrupt Status (RIS) register. */
  while ((HWREG(SYSCTL_RIS) & SYSCTL_RIS_PLLLRIS) == 0);

  /* 5. Enable use of the PLL by clearing the BYPASS bit in RCC and RCC2. */
  rcc &= ~SYSCTL_RCC_BYPASS;
  rcc2 &= ~SYSCTL_RCC2_BYPASS2;
  rcc |= (TIVA_BYPASS_VALUE << 11);
  rcc2 |= (TIVA_BYPASS_VALUE << 11);
  HWREG(SYSCTL_RCC) = rcc;
  HWREG(SYSCTL_RCC2) = rcc2;

#if HAL_USE_PWM
  HWREG(SYSCTL_RCC) |= TIVA_PWM_FIELDS;
#endif

#if defined(TIVA_UDMA_REQUIRED)
  udmaInit();
#endif
}

/**
 * @}
 */